Відео

The new field piece and navac ones are really nice . The one is most commonly see in the field is the Appion G5 Twin . If you’re going to invest one , make sure it uses a DC brushless motor as well as your vacuum pump . Reason for this is the new line of refrigerants coming next year to replace r410a are classified as flammable and the manufacturers only want brushless motors used so there is no chance for spark ignition ( even though a spark wouldn’t ignite them anyway , it’s a safety precaution )

I’m the channel creator , this is my personal profile ( sorry I was signed into the wrong account when replying

@@lammaking333 Ok, thanks. Appreciate your advice.

Could be a few different things but immediate thought would be low on charge. Check all connections including threaded connections for sensors and transducers , king valves , etc with soap bubbles . Many leaks common from those areas on all Trane chillers. Pull all panels and inspect coils for oil stains . It’s possible could be a metering device problem but not likely - usually you’d get a low suction super heat alarm. After checking with bubbles , pull the water strainer and verify if it’s clean or dirty . Final step to actually know for sure if it’s low charge would be recover the charge and weigh the charge and compare to data tag. If for example your charge weight is 120 lbs and you only recover 70 lbs this for sure would be your tell tale sign. Hope this helps

It’s been awhile but off the top of my head I think it was anywhere from 2-4 weeks

Thanks for watching

Most pump's recommend after every use, which I assume would be every couple of days worth of use. A used oil would not allow the pump to pull-down vacuum to full spec. So a pump that can do 25 microns, would top out at 100 or 200 microns with used oil. So you can close off all the vacuum ports, and just have a gauge attached, and see if you can get the spec to check oil condition. Basically the oil is hydroscopic, and absorbs moisture and other stuff that degrades it's performance. Also this Fieldpiece pump has two reservoirs, and allows an oil change without breaking vacuum.

The Klein backpack I had years ago was a good bag , but when you unzipped it , it would not stand up right and would tip over , which was very annoying . I will say this from experience , Veto bags are higher quality and more catered to and have more thought put into the pouch placement and overall design and are more Durable and have a five year warranty. That being said , if you’re trying to save money the Klein bag is still a fantastic bag for the price , and last I checked , the Klein backpack had a lifetime warranty through Home Depot. Meaning you could just bring your old torn up bag in and walk out with a new one same day. I’m not sure if that’s still their policy , but you can’t go wrong with either.

Ok thanks for letting me know your experience ,I live in Canada, the veto bag is over 550 with tax and shipping the Klein is 275 plus tax and shipping,

Thanks for watching

It really should be some type of mechanical code to install them on large split systems over a certain tonnage/btu.

Not for r22. If you have an r22 txv or piston , no adjustment is needed. Evacuate system , replace drier , weigh in charge as liquid close to but a little under the original charge weight , then throttle in remaining charge through suction until superheat / subcooling values are in range depending on your metering device .

It's only that easy when you are using the setup you are using (MQ converting with p/t programmed in). If you are using simple manifold gauges, you need to convert pressure values to temperatures using the pressure temperature chart for R422b (Nu22b). It is not exactly the same like many think it is. www.freon.com/en/-/media/files/freon/freon-mo99-nu22b-retrofit-guidelines.pdf?rev=cb47ceae0ca247879c21e65941aa1546 pgs 13-17 Thanks for the video. Great diagnosis and info.

Thanks for watching

Yessir , recovery and charging should only been done with verified water flow on chilled water systems to prevent potential freezing issues in the tubes or heat exchanger

Yes they can be used on a heat pump system , however it will require the addition al installation of some type of relay such as a SPDT ( single pole double throw ) with the coil wired to “O” , this will allow it bypass control in heating mode, depending on if your unit energizes reversing valve in heat or cool. You don’t actually want the fan cycle switch to be active when running in heat mode as it is likely to cause a freeze up at the outdoor coil due to low airflow when in heating mode.

No point in overpaying for hand tools that will preform in a similar manner than a cheaper version and that are likely to get beat up from use anyway. Save your money for the high quality tools you actually need or power tools.

Thanks for watching

No sir we did not . But we came back a month or two after this call for all the chillers on this school district and submitted oil analysis as part of the annual pm

@lammaking333 nicely done...oil analysis is a big key to spot a potential major issue

Thanks for watching

Hi thanks for watching. That is the measurequick app. There is a free and paid version . It is compatible with different brands of Bluetooth testing equipment

It means that the gas ballast is open

No it sits in a well just like on the compressor

Still using . It now serves as my Bluetooth testing set. It fits both my fieldpiece and test probes as well as 3 stubby ball valve hoses , with room for service wrench , spare shrader caps and core removal tools

🤔

I’m located in Ft Worth. Greetings fellow Texan

Me too.

Thanks ! Did a show May 27th this yea , got 2nd place and 3rd place in two classes of Classic Physique. Going on a bulking phase currently and next show is October or December next year . I used to do fitness content but there’s so many people making videos like that I never got any views. You can follow my fitness Instagram @ Tighe_Philbin

@dfwhvac Keep at it man! All of my coworkers and fellow tradesmen just drink beer and get progressively fatter every day. Glad to see someone else out there is on this grind!

It’s husky brand from Home Depot , you can find it in the tool bag isle. It’s pretty light weight but extremely durable and secures very well and is water proof. Only costs $10-15. It’s held up very well , I would definitely recommend it

Awesome tip man ! Never tried that but that makes sense ! Great comment .

Great to hear man and glad I can help ! They’re intimidating at first but if you have someone show you how to do it it’s not as hard as you’d think ! That’s why I make these videos

This comment is wild man haha. I never work one handed on anything that would ever pose a risk or legitimately require two hands to work with. I’m 100 percent confident in my skills and never do any work or leave equipment in a state that something detrimental might happen . If equipment poses an actual risk it gets locked out and tagged out. You’ve never checked voltage with one hand with two meter leads ? I appreciate the comment but the insurance thing is king of far out there man haha

Next time I run into that scope of work I will definitely make that video !

It was a promotional offer from Veto. Check their website every so often , they have deals Pop up at random .