Відео

Hello, where did you get the prints for the gate connections or did you design them yourself?

Nice work fo the community!💛

Awesome!!! Thank you!!!

I bought 2 Mobula 7s when they first came out. I don't recall getting 8 minutes of flight time. Definitely little screamers though! Nice flying!

Please do a tutorial on how to make the light power connector. Thanks!

Thanks for sharing! Have you done a video on how to make the lighter power connection? If not, please do.

To its Wicked Faaast!!!! And the TIME!! 🤯!! So, Can we get a “OUTSIDE” view of how the quad looks like flying indoors/outdoors to get a Feel for speed ? I see FPV is hard to see so fast! But, maybe next video? So GOOD! #dronefpv

I like video good job .. Suggestions on cap size?

How do I buy a add on for 2s OR Two 1s batteries? I can’t seem to fit my batteries without “Rigging” w/rubber bands.. sucks. They fly off and just no good, any suggestions? I’m thinking if Quad blades too.. 🤔

What is it the vtx problem?

Sztos! <3

Please description fix what is Pitch and size of the props ?

I think I have found the problem with my 5-1 bad reception. I noticed the amperage in the OSD right before takeoff was at 1.8 amps on the air 75 with the 5-1 but on my air 65 and the mobula 65 the amperage was only .2 amps. So just as a test, I turned the IPX connector a tiny bit on the air 75 with 5-1 board and all of a sudden the amperage went back down to .2 amp instead of 1.8 amps. So after it went back down to the .2 amps I flew the 75 and now everything is fine but if I barely move the IPX connector the other way it goes back to 1.8 amps then the reception is very bad again. There’s something going on with the IPX connector on the new 5-1 AIO so at this point I’ve locked it down in the good position with some liquid electrical tape and everything seems to be fine at this point. It’s so bizarre that I found this using the amp data in the OSD. I still don’t have any clue why the amperage runs up high in a certain position must be some type of a short or something.

Great VID, a little tip from me, I spent a lot of time to set everything right, I had builds where I put my VTX antenta like you under the battery, It came out to be the worst spot ever regarding to Video quality, i reccomend puting the antena somewhere outside - Bless you - Keep grinding :)

I wonder if you didn't get a busted VTX. I've built 4 copies on this AIO. 16.85g. None of them have VTX problems. I use a trimmed antenna for the VTX. I've flown 3 specific trainings with one design. To check durability. About 30 batteries on each. No problems so far.

Great video - vtx signal looks like crap - especialy 200 mv output. I know they upgraded vtx to 1.1 v maybe it will solve the problem.

Nice testing my whoop friend! Thank you for the video!

Love it! Great flying as well. Can't wait to see the build vid. I'm subb'n ya bro!

Acro mode?

Nice 🙂👍🏻

Did u solder different wires to the camera than the stock ones? My camera came with very thin wires and yours are thick.

i love this man

Betaflight configurator settings?

What battery did you use?

wpadłem jeszcze raz bo "kiedyś" gdzieś widziałem podstawkę do lutowania XD. Jest gdzieś ogólnodostępny stl? 00:24:12

"My skill is not very good" Bro... they are excellent

GREAT BUILD❤❤❤

Awesome video! Sorry, my question is, can I mount a flysky fs-ia6B to tthis drone, even if it will fly bad?

What should I do to be able to use it with a flysky fs-i6 controller?

Hi. This Launch control stand from beginning is your design or it could be find on the internet?

What's the purpose of the pigtail? Sorry I'm new to the hobby.

whats your googles aand setup on them? Im trying to get back to hobby with only tinywhoops and I am wondering which google should I buy to have decent video

So cool! What do you think about doing 35mm props with 15000kv motors for even less weight and a smaller quad.

Yesterday I almost lost my drone because the Jumper's batteries got loose, the controller lost power and dropped the RC link. It was just that metal tab you showed how to bend back. Lesson learned - before you fly, shake your controller to make sure it doesn't power off because of loose batteries.

Brother, you're one helluva ripper - Definitely deserve WAY more subs. Stay up bro ✌️

that voltage drop is pretty impressive, very steady and slow.

Would you have the stl file for the case

Why only 2 screws mounting the motors?

Super setup, nice flying. Do you mind sharing your tunes and how do you set the launching mode 5:01 , thanks

Nice build. And strong pilot skills, that`s nice!

for a beginner, what kind of drones you recommend for a start? Should i buy cheap E010 or anything else ?

betaflight config video ?

Also btw how do you make drone push up back side for a faster start?

Couldn't find those 14k KV motors. Also what did you put in battery holder to make it right size?

Hi. Find out today big problem. Hope you can help me solve it. Went to fly my Meteor65pro, but it didn't work. When plugged in battery the motors do the beep sound, but nothing else. ELRS receiver is not working, neither VTX. Betaflight or PC doesn't see the drone when pugged(can se other drones, cable/betaflight/drivers are fine). Not sure if it does anything to do with it, on my last fright it says heat alert 74*C, but I landed immediately. What could it be and what can I do to help it. Thanks.

Wow, you are so pro... its hard to see what is going on there, but you do fly it omg. Would like to ask you an hardware question: I burned out FC on Firefly1.6 1s toothpick. But the boards are sold out around 6months already(AIO 5A board w/ built in VTX). What could I change it with - suggest pls.

how do you lean forward like that?

@grox I am new to fpv drones, I bought a TinyHawk 2, I dare not fly it, did you use simulation or went straight into flying, what is you're opinion, should I do simulation before flying in the open empty field ?

What is the size of the squares you fly through?

So awesome, it is a rocket 🚀 i have a mobula 7 v2, it has GEPRC SPEEDX2 0802 16000kv motors, do you think these could be good for same satup you have? I have the estock fc too, by the way could you please share prop specs, like what pitch those are, i need 40mm prop but not sure what to buy so would like to test the same you used on this build