- 2
- 130 058
Owl Fab
Приєднався 26 гру 2016
Workshop projects in Colorado.
2017 Eclipse Denver
I set up a basic eclipse projector at work today using one side of a pair of binoculars and a simple three leg stand. This is a time lapse of the projection from about 11:00 - 12:15 MDT. Max. eclipse occurs at about 0:49.
Переглядів: 202
Відео
Etching Aluminum Name Plates
Переглядів 130 тис.7 років тому
Electrolytic etching new aluminum name plates for a Hobart welder restoration project.
this is brilliant 👌
Ap goldan sateel pe Kon sa aeran istmal Marty hian pleas batean
My masking are coming off during etching. What can you recommend to do? Thank you
See that: instagram.com/porcuscraft
Thank you for your Video. Can you suggest any alternative chemical other than Hydrochloride Acid for aluminum Etching. Thank you
What is the printing pepper ??
Which powder used
Plain table salt, NaCl.
Excellent!
Excellent!!
Hi very nice price of the this machine please contact me
Thank you for your video Owl Fab, It's great content and well made!!! I have one question tho, my DC power supply only run up to 30V and 5A. Is it enough? Thanks in advance.
Probably a bit slower, but it'll work fine.
What brand of DC machine
Etching was nice but looked way better with the stickers!
What product you used?
Nice shear!!! I want one now :)
hi.. tQ for the fantastic video n tQ for sharing it. small font subs along the processes like the one at the end could hv been very very informative ..
how many volt/ampere minimum to make it work ?
You don't need electricity at all, you can cold etch, but it takes a lot longer and requires more brushing off of the surface. Lower and slower will produce a sharper finish etch, too much can undercut the stencil and ruin the sharp lines. Owl Fab uses a very mild electrolyte, just salt and water, which works fine, and can take higher volt/amps. You can add white vinegar to that salt water solution making it act faster, but you would lower your volts/amps. There are many different electrolyte solutions you can make/use, ferric chloride, dilute muriatic acid, (these should only be used with very good ventilation as they put off nasty fumes.)
David Johnston Fuck you for NOT answering Tedi Sopian's question!! Whahahahaaaaa! So i'll do it for you fucker! 9 volts and 2 amps will work already. I usually work wit 12v and 6 to 10 amps depending on material and object size.
how can i put paint on letters...is it possible to use in outside.? pls replay
Sreejith I would paint the whole thing after etching, then sand the plate on a flat surface. Paint will remain in the etched areas. As long as you use exterior paint it will be fine outside
can i use plastic sellotape or something like PVC electrical insulation tape? as an etching mask or resist?and if not why not?
+Pero Vaper Sure you can. How long it remains adhered will be the limiting factor.
I have videos like this in my channel
Very nice. We used a similar technique to make a big Workshopsign. check it out ua-cam.com/video/h-qvuwjsg6k/v-deo.html
What are the blue sticky dots you placed on back? and why?
nothing inportence
+Solaro Studios I believe it's called fun tack, used for putting posters on walls. I used it to seal the spots where the tape seal might fail.
its called blue tuck
chad danylak My 'inportence' is shitty too.
Oooo man!!! Thanks, thanks, thanks.
Does it etch deep enough to paint the whole surface afterwards and then sand it off leaving the etch painted? Thanks for posting the video and tutorial!
Potter's Work I have not tried this, but I believe the etch is deep enough for this to work.
I did an acid etch this last weekend and using Muriatic acid and hydrogen peroxide. worked great. Used some tips from your video as well. Thanks!
and how do we call that power supply unit?
+U Khun Wan Htut The electrolyte is a saturated sodium chloride solution. Just mix table salt into warm water until it won't dissolve more. The power supply is a generic 30v / 10A unit that I purchased from eBay. AliExpress has them too.
Owl Fab I really appreciate your art works and your replies. Thank in deed and waiting your new videos.
what kind of solution do you use for that etching?
salt and water solution or can use any electrolyte solution that can can pass electricity.
That came out so clean and precise. how many volts were you running to etch?
Suedzville It ran at 10v-11v and 10A. My power supply is capable of 30v/10A and was turned all the way up.
Thanks Owl Fab. I appreciate it.