- 51
- 92 480
Dugefrshautomotive
Приєднався 6 лют 2012
Відео
first drive of 2015 Focus ST
Переглядів 52Рік тому
catless 3 inch Roush exhaust greddy turbocharger unknown other mods and tune auction purchase
Pacaar MX13 injector removal, inspection and replacement. fuel in oil
Переглядів 45 тис.3 роки тому
complaint was diesel in the oil. conclusion was a leaky injector. replaced injector with a certified pre owned injector. 2012 Peterbilt with Pacaar MX 13 engine.
Looking at properties in central Florida
Переглядів 93 роки тому
Looking at properties in central Florida
Thanks
Thank you
I have " spill injector valve " code on dash ,any idea? 😅 2 years working on it no more than 20 boost😢 Thanks in advance 🎉
good videa fuckin helped
can you replace injector tubes in truck ?
Good info
Was this done on a epa 10
wtf you using for a phone samsung galaxy s3 from 15 years ago ?! hahahahahah
Buenas tardes amigo,y para calibrar el freno de motor cuale es el procedimiento
Hello Friends, I have a daf model 2020 mx13 engine, engine retard. Why does this engine damage the camshaft, and I have seen several cases where the camshaft also breaks quickly, and this is a weakness for this engine. Is this a weakness in the construction of this engine or is there a reason that causes this problem? Please guide me. This is a problem for this engine and the second question is what type of oil is suitable for this engine. Please answer Thanks
How much for the work
If u take flap out will it help power?
How do you replace fuel line 6 without removing the head???
Jack up the cab.
Any ideas for a removing the injector thats seized in there
Have you tried a slide hammer?
Would black smoke and misfiring be an injector? I was driving just fine and all the sudden started misfiring and black smoke out the back.
Could be... Could be stuck turbo.
@@Dugefrshautomotive that was my first thought but I was getting full boost at the time. I took a stab at it and I installed new injectors the next day and it ran like new!
Sir do want helper hehe😁
Thanks bro!!
Is this mx13 epa 10?
EPA 10
PACCAR ONZELL TUP SIVICE
Hello sir, were you able to get the actuator back into the housing? I’m also working on my egr for the same exact truck you have. Right now egr valves for this truck is impossible to find so im trying to rebuild mine. Pulled the actuator out to service the O-rings to fix the leaking oil but now the actuator/valve won’t sit all the way into the housing. Were you able to put yours back together? If so, how? Thanks so much for any info you can provide man. You’re my last hope. Have a good one man. Thanks
Sorry. Mine just simply went back together without any tricks. But I didn't change any orings. I just freed up the frozen valve and reinstalled on engine.
Do you need to adjust valve/check clearance on valve bridge after installation
It's definitely recommended and makes sense to do it while you have the valve cover off.
@@Dugefrshautomotive hopefully this thread isnt too old, I can not find any specs on the injector rocker clearance, only intake & exhaust (IN)(.020) // (EX)(.028) ???
Why diseal mix with water for pacca engine
One possiblity is the injector cups. But there's also other spots for fuel and coolant to mix depending on make, model, and options.... Such as at the fuel/water separator
Besides fuel in oil what other synthoms will u feel in the engine when one injector is bad ?
You should feel the misfire and check engine light triggered
@@Dugefrshautomotive my truck had 2 sensors bad and a fuel pressure valve bad that's why it was feeling like a bad injector now has a oil leak that can't be run 😕 seems always some bs with this paccar it only have 430xxx miles I got it when 364xxx so I be beyond on point with pms and everything so I'm changing my mind about them ... I'm looking in to volvos now
@@elvynortiz3456 what sensor was bad?
@@FrankSerrano mecanic dint say that's why I stop goin to him 😒
Bad wire harness
is there any computer reset needed for this after the injector is replaced?
No. Computer will keep code as inactive but check engine light will go out.
How did you get the coolant lines off the EGR valve
I don't know. I got this motor already in pieces and since then I've just stripped it for parts.
Did you remember seen oil in position sensor?
What do you mean?
@@Dugefrshautomotivedid u remember seen oil in the egr actuator position? U did say the sensor tell the position of the valve. Did u remember seen black oil in it?
@@johnsonberry6750 I don't know for sure where oil might be. This engine hasn't been together in years, do there's no oil anywhere at this point. I was just tinkering with it to see how things work. I found that the EGR works off of oil pressure. So engine needs to be running in order to command the EGR open and closed. I plan to video the entire tear down and rebuild of the engine once I have spare time.
@@johnsonberry6750 yes... The actuator and sensor most likely bathes in engine oil. I tested it in another video with air pressure. So it makes sense that oil touches everything in the actuator/sensor assembly
Did you figure out anything. Davie program has a function to initialize the egr valve which test function at idle
Not yet. Got the truck with engine partially rebuilt. was simply tinkering that day. I've never done a paccaar rebuild. But I'll be getting to this project soon.
If you could find any ID marks on that solenoid would be great. I have one needs a solenoid but they only sell the complete valve. It’s crazy. Parts prices are astronomical
@@jeffderus1668 I still have it in pieces from last year. I'll check it for any markings.
I’m guessing that’s a cleaned egr valve?
Not cleaned. Just removed off engine. I was simply trying to determine how it works. Needs pressure in order to operate.
Hey buddy did you found anything more about this?