![bokm9606](/img/default-banner.jpg)
- 17
- 47 540
bokm9606
Приєднався 23 вер 2011
W124 1987 300D Rear Window Repair (fix
This Video shows the issue and repair made to the inoperable rear window in my 1987 W124 Mercedes Benz E300D. Ultimately, the issue was that the wires in the door hinge area were fatigued and broken.
Переглядів: 90
Відео
ESPN NFL 2K5 Vinatieri Blocked Field Goal
Переглядів 1367 місяців тому
Grant Wistrom gets vertical to block this FG attempt in Overtime. #nflfootball #2k5 #nfl2k5 #Vinatieri #gamingvideos
1987 W124 Mercedes Benz - Stereo - Fader switch bypass
Переглядів 1,8 тис.Рік тому
This video shows what I learned concerning fader switch bypass for my recently acquired 1987 w124 Mercedes Benz Stereo (300 Turbo Diesel).
w124 1994 e320 dash speaker debug.
Переглядів 3132 роки тому
my 1994 e320 stereo was sounding way out of balance. the sounds tended be too strong on the treble and dominant in the front dash speakers. Speaker impedance m tters!
2000 EXPLORER "ON BOARD COMPUTER" (Message center) BUTTON LIGHT REPAIR
Переглядів 3062 роки тому
This video shows where the two bulbs are for the illumination for the buttons for the center console on board computer/message center (equipped on some models of 2nd Gen Explorers and Mountaineers)
OM606 1995 Mercedes Benz E300 Diesel EGR Fix and Delete
Переглядів 3,5 тис.3 роки тому
This was a temporary fix for the EGR valve that effectively "deletes" dirty exhaust air from entering the intake. Motor is OM606, naturally aspirated 1995 w124 chassis Mercedes Benz
1990 BMW 525i e34 SRS airbag - clear warning light procedure
Переглядів 15 тис.4 роки тому
This was the procedure I used to clear the SRS light on my 1990 e34 BMW 525i. Please note this took me a few tries to get the 5 second timing correct.
CB175 VelocityStack 3D printed
Переглядів 1514 роки тому
3D-printed velocity stack tube that adapts Honda CB175 Carburetor boot to Air pod/ filter. Design intent is to condition the airflow into the carburetor to be laminar - not turbulent.
Mercedes 1994 w124 e300d keyless module install
Переглядів 17 тис.5 років тому
How Installed keyless entry module in my w124
W124 Mercedes e class radio install with Iso connectors e300d
Переглядів 3,1 тис.5 років тому
Iso standard connectors make install easy Mercedes Benz Boss Audio
Marshawn Lynch - The Beast of Madden '08 PC
Переглядів 7479 років тому
I created this video with the UA-cam Video Editor (ua-cam.com/users/editor)
Marshawn Lynch Beast mode on Madden 08 PC.
Переглядів 579 років тому
Marshawn Lynch Beast mode on Madden 08 PC.
Thank you.
Any performance upgrade lol? Nice fix, how has it been holding up?
Thanks! I have the exact same car. Why not remove and block off the EGR port on the intake completely?
thx 4 info i have struggle with my fader aswell XD
Does this work for 95 e34 ????
What radio head unit do you have? Also would the message center be able to work in the xlt trim level?
My stereo is a double din jvc media receiver. My understanding is that adding the comm module to an explorer that wasn't originally equipped is a real PITA.
@@bokm9606 Thanks for the response! Also, I may take on that task at some point, the comm module is cheap enough to take the gamble if im willing to put in the work. I use my explorer as a daily and road trip car so the miles till empty seems useful
Hey, any chance you could post your stl file for the button on thingiverse or something? I have an 87 and the fader just broke entirely and I was looking up how to bypass it. Thanks for making the video! To make a smooth finish for the 3d print, look up acetone vapor. That's what I do for my 3d print to make them smooth.
I can email you if you post address or I can put on Grabcad
I got smoother finish by setting bed level closer to the nozzle
I printed cosmetic surface against glass bed
@@bokm9606 I commented with my eamil address but I think they blocked it? If you could host it somewhere that would be great. Thanks!
The STL file is posted to GrabCAD. You should be able to search "W124 fader switch blank" at GrabCAD and find it.
Oh my god! I was trying and trying to get this thing out of my parts car. You just saved my ass!
💔 Pᵣₒmₒˢᵐ
thanks man! hoping a new brake light switch lets me use my cruise control again!
Thanks for sharing.
You have any reference to the Gray/Red wire you taped into for the lights? Thread or other wires contain in that bundle
Can you show me how the diagrams please??
Can you show me how the diagrams please??
Thanks a lot for this video. Good idea on the switch. I had read on a forum years ago about this process and saved that page somewhere. Recently i changed my steering wheel and the SRS came on and wont go away after plugging everything back in correctly. I have an e36 92 325I (OBD1) that this applies to. Cheers!
Здравствуйте! Не подскажите в блоке управления нужно что то делать ?
I have this car now!!! Text me
Hey man, where did you buy that filter, can you please provide the amazon link ?
ASIN number from Amazon is B07KMQHYL6. As of today, it shows as unavailable.
Great recommendation. I cut the pin head and sleeve by wire cuter, because no room for two hands. Thank you so much.
I don't have the 15th pin in my e46
Your car doesnt have immobilizer that works synch'd with the key?
Have to try this... my '93 E32 has the same issue. Can't find any software to disable the light. Thanks
It took me a few tries to get timing right
I have a '91 525i (build date 10/90) and I also had this issue when I replaced the dash bulbs in the cluster. I found on my car I had to turn the key to position 1 (acc), not position 2 (on) to get this to work on my car. 90-91 was a transition period for the 525i for engines and SRS electronics IIRC.
Try it on all pro or legendary difficulty
Great video! 2k lives forever!
I wish this was in more detail esp on the pump side . To see what wires you attached to would been a better video . Thanks for trying to explain though ; )
Hello I own a 2005 Chrysler Crossfire ( Its made by Mercedes SLK ) and I lost one of my Transponder chips from my flip keys I had taken the last working key transponder out of my working key so I can use any cut key I bought a cheap remote locking VW type flip key remote locking system similar to yours . I wanted to know if this will work on my car so I could either use the factory key or the aftermarket system. Could you advise ?? thanks
Congratulations, I've tried blocking hundreds of kicks on this game and never got a single one lol
That is my only block. Never have blocked a punt though. The game is off the hook
Just an update did you get good remote range by adding it on next to the top of the trunk? Im thinking of adding it also in the trunk. They say to put the module next to the vacuum door pump
Not working 😭
It took me about 5 tries to get the timing right.
@@bokm9606 after about 7 times, no luck, i used the same trick, wire, switch, its annoying. no modern tester can disable the error, they see it, but cant disable . WT actuall F?!
@@RCmadness888 be really meticulous on the counting of time. Use a stop watch
@@bokm9606 Yes, i did, i read it that the timing is like crucial, but its like to the milisecond?! I had my watch, i did it in every 5 second mark.
@@RCmadness888 it took me several tries. I wonder if taking the key all the out before attempting has something to do with success of lack of success. Maybe also vary the timing of how quickly you turn the key to the on position...? I know that it felt like i did the same process over and over but eventually it worked.
Can you please show where the speaker wire connect on the keyless entry
I did not install the horn wire on my car.
Thanks for replying.....my question was...I've notice you connect a regular speaker wire to the door lock using the green wire on the round connector....my question is , where do that wire goes on the keyless entry. I am using a Installgear keyless entry locking system...Thanks in advance
@@rayfordcadle9160 on my unit, (FICBOX Universal Car Door Lock Vehicle Keyless Entry System Auto Remote Central Kit with Control Box ) two wires were connected to the green wire in the car. After cutting the green wire near the pneumatic box under the seat, the WHITE wire from the keyless module was connected to end of the green wire leading directly into the the pneumatic box. The ORANGE/BLACK wire from the keyless entry module then connected to the end of the green wire leading AWAY from the pneumatic box under the seat. ALSO, two wires from the keyless entry module needed to be shorted together - on my box, these wires were ORANGE and WHITE/BLACK. This URL was helpful: www.peachparts.com/shopforum/diesel-discussion/283569-diy-keyless-entry-door-lock-w126-w124.html
@@bokm9606 Hello Pete, i had purchase the same keyless entry as you have use on your mercedes and follow your guide but i have no luck with mine, i did exactly the way you explain just that i left with 2 wire which is a yellow and a yellow and black unconnected. I thank you for your help.
The Boss Audio 460BRGB was the unit shown in this video. bossaudio.com/product/460brgb/
show everything or nothing.
where can i buy the antenna adapter ?
Generic Factory Antenna Adapter to Aftermarket Car Dash DVD Head Unit Radio Adapter ISO to Din Antenna Aerial www.amazon.com/dp/B00JE4GY9O/ref=cm_sw_r_cp_apa_i_wFSkCb9KQKQNS