53
136 479

13:02

Changing the oil

5:26

How to aneal a copper washer

1:36

Checking drive belt tensions

2:36

Changing the coolant

4:09

Adjusting the Handbrake (engine in car)

8:28

Removing the Steering Rack

This is a cut-down from the Lockdown Trilogy of full engine removal and re-fitting. There are extra bits about marking the splines before removal to help re-alignment.

Відео

13:02

Refitting the Steering Rack

Переглядів 5952 роки тому

This is a cut-down from the Lockdown Trilogy of full engine removal and re-fitting. There are extra bits about marking the splines before removal to help re-alignment.

5:26

Changing the oil

Переглядів 6082 роки тому

This is how to change the oil without changing the filter. It is a cut down from the original oil and filter video but is obviously much shorter as it doesn't include the sequence about the filter. Without a filter change you'll need 4.5 litres of oil or 8 pints to refill.

1:36

How to aneal a copper washer

Переглядів 5 тис.2 роки тому

This is a cut down video from the original oil and filter change video. Just for convenience really... Remember you can't do it to a collapsible type only to a solid copper washer.

2:36

Checking drive belt tensions

Переглядів 2812 роки тому

The service schedule says to check drive belt tensions but not how to do this and how tight they should be. Adie shows you how. This is the updated version with a small correction. (Thanks Tor)

4:09

Changing the coolant

Переглядів 8942 роки тому

How and where to drain the coolant and what to refill it with. Not a true demonstration due to filming constraints but it should be all the information you need....

8:28

Adjusting the Handbrake (engine in car)

Переглядів 7122 роки тому

Part of the service schedule as well as a requirement for the MOT test, adjusting the Parking / Emergency / Handbrake is at best difficult and at worst, without the special tool, impossible. Full details in the video...

2:31

Checking the coolant level

Переглядів 6482 роки тому

How to check the coolant level. This video shows both types of radiator, with and without expansion tank.

2:22

Adjusting the rear brakes

Переглядів 6682 роки тому

Part of the service schedule, this is how to adjust for wear on the rear brake shoes.

1:22

Radiator shroud zip

Переглядів 4442 роки тому

Checking and clearing the radiator fins is part of the service schedule. The zip on the shroud is to give access for this. There is one other use for it, which is mentioned in the video, but otherwise it should remain properly closed at all times

6:46

Adjusting the clutch (BVM)

Переглядів 7932 роки тому

How to adjust the manual (BVM) clutch on a DS/ID. Starting with checking the free play on the pedal, then adjusting the push rod clearance and finally adjusting the pedal free play.

0:57

Oiling the dynamo rear bearing

Переглядів 3922 роки тому

This is part of the service schedule for older cars with a dynamo. A couple of drops of oil on the rear bearing. NB this is NOT for cars with an alternator.

1:00

Oiling the air horn compressor

Переглядів 2,8 тис.2 роки тому

Part of the service schedule for cars with air horns fitted.

9:37

Checking and changing the gearbox oil

Переглядів 9132 роки тому

Not really about checking the gearbox oil level - Adie explains why in the video. Very much about how to change the gearbox oil on both 4 and 5 speed gearboxes.

23:18

Adjusting the Valve Clearances

Переглядів 1,6 тис.2 роки тому

This is a re-working of the the previous version, this time to add a caption about removing the spark plugs to reduce resistance when turning the engine over by hand.