Відео

I have a 207mm crank pulley on stage 2 and my belt keeps squealing and shredding. Will this new pulley fix that issue?

Alignment

What model and make of motor mount is going to fit the same car but with 2.0 liter diesel engine?

That's not Mexico. Liar

on e40 and dual pulley how much hp is it pushing? also i picked up an a6 couple weeks ago and when i did research apparently the 3.0t tops out at around 600hp due to fueling?

how hard was it to remove the cats from these cars?

Hey, i know this is an old video. But was the C7.5 box bigger by volume compared to the old one?

Do you have the throttle body part number?

What headers/extractors have you got on this beast. Notice any power gains?

Do u have to take off supercharger to change valve cover ?

What is the part number for the shaft bearings (nearest to the sc pulley) in the snout?

Who’s your tuner ?

Bro you for real inspired me to get an a6 and I finally got one a year ago. I’m currently 034 stage 2+ and I’ve done everything myself I got some videos on what I’ve done to it but anyway I’m looking into a watermeth setup and I was wondering how much watermeth do you go though like per full tank of gas, or something like that just wondering how often I’d have to buy it. Thanks

Nice setup! How’s the drone?

Bro the gum chewing 😅

Where is the crackle tune on IE

Will that work on a a4

Did you ever mess around and see how much temp difference there is with open filter vs stock air box ? Just wondering since you can check intake temps

Where you order from

You should mount a 4ft led light on your open hood. It would provide great lighting, so you/we can see better. Thanks for the great content.

Where did u gett paddle shifters

Are the pistons stock?

What’s the benefit of this?

Wish you could work on my s7 brah lol.

Subscribed! Thanks for the info!

Any update on the headers looking to buy these

What happen to you brotha?

Do I need to be dual pulley in order to install this throttle body or I can just do it with single pulley? Thanks

Gamecock Ave? Where ya at son? Chas sc here

May I ask how reliable are these cars. I'm about to buy a 16 audi a6 3.0t. Then get stage 2 tune,heat exchanger,and other goodies. I wong be racing barely ever. Just want to make sure they last for years.

belo trabalho , teria numeros de desempenho com sc portado ?

Where the headers any good?

just picked up a 102k 2012 a6 prestige - on the lot a motor mount was broken if 1 is broken are the other 2 going to break soon as well?

85% duty cycle is maxed out on these cars

Bro you talk like a asshole

356mm front rotors ?

How many mm do the 356 rotors have?

who did your tuning with those mismatched pullies?

We hear you chewing gum 😅🤣

I got a 12 a6 C7 and I see you putting in nice detailed work. I just gotta question because you are in the area of point with the pcv valve? I have a whistle noise going on and want to no if I'm really spending necessary money on the correct problem before I go all out and fully customize everything to my personal preferences digging that deep?

I have a 2015 A8 with 40k miles , got a sick deal on it so enough left in the change purse to build and tune it a little. It's a gorgeous car. Are you happy with what you did to your A6?

Cabin you add the part numbers please that you use. Thanks. And keep up the good work with the videos!

What are the magnaflo parts that you used?

Did you have to remove the engine in order to install those headers ? And how much was the labor cost ?

What do they send you when you purchase stage ecu tune? A new ecu or software

hi! please tell me what was the difference in power and time after installing the ported supercharger? PS you followed me in dragy, for some reason I can't write comments there- I have a6 c7 single pulley, ecu and tcu revo (most likely they use tvs software for dsg). a custom intake and exhaust manifolds are installed. cooling of the compressor is stock. the best time is 11.98 1/4, 9.9 100-200 and 3.96 0-100.this is in full weight and at 255/35 r20. the plans include porting the supercharger and an enlarged heat exchanger. so far, single pulley setap, since revo allows you to change fuel cards using revo sps, and there is not always normal gasoline in my area

What's the update on the a6? Have you ran at the track since you've installed the lpfp?

Now get that TCU tune and see what the difference is.

Wiring mod diagram?

Can u tell me where to buy everything