Відео

Did you need to relocate the handbrake to fit the swivel seats?

Mooie bus! Ik heb ook net een Renault Master gekocht. Hij is al ingebouwd, maar volgend jaar ga ik hem denk ik opnieuw inrichten, want de inbouw kan een stukje mooier/praktischer. Ik ga je volgen, want zie veel leuke tips in je videos :).

My door is low by about 10mm at the front when closed, it's hard to close, I replaced the top and bottom rollers but still has the gap on the top and no gap on the bottom

Obrigado pelo vídeo, parabéns.

No need to remove the inner pannel !!!!!! Just use the small hole on the side of the door to perform the unlock. But thanks for the video, it was also funny for me to remove the whole inner pannel 😅😅 but i broke several small fixings

What are the fitting thread sizes on the water heater?

Great work, was one kit of 4 litres enough to cover the whole side + bonnet, I have LWB sprinter and deciding how many litres I need for raptor liner

Donde compraste la goma de la puerta

En el minuto 5:04, en argentina, el movimiento es para el otro lado muchachos.

What a great compact setup you have created.

Thx for your video 1. Hate that Renault made these door handles sooo weak 2. Hate they made so difficult access to that door handle from inside!

Thank you 😊

thanks...

Jak wyregulować dzwi przednie mowano b

Gostei muito do seu vídeo muito detalhado parabéns

Appreciate the vid....was the broken bit from the inner part of door handle, or the outer bit....i need to get a new one and on ebay, they sell them as just the outer part (about aud$25) or the whole lot..inside bit and outside bit ..at least double the price, so just wondered if worth getting the whole piece or i just need new outer handle bit? Cheers..just rewatched vid..think u only replaced outer part..cheers

You didn’t need any rubber seal gasket glue?

I bought a master which was delivered yesterday by a driver who broke this indicator unit whilst reversing the vehicle onto my driveway! I ordered a replacement online but couldn't figure out how to remove the old lens unit so, you video was an absolute godsend. Thank you so much for taking the time to post it.

I have been looking for idea on how to do this on my sailboat. Thanks, this was very helpful. Anything to say about the water heater 2 years later?

Also wenn man zu dumm ist diese Dichtung zu tauschen, sollt man gar nicht daran denken einen Van selbst umzubauen 😂

Demotaz zamka centralnego przód lewy jak

Mag ik je vragen waar je de verf kan kopen...

Bonjour, Merci beaucoup. Bonne journée à vous.

Thanks

hej lars, very glad i stumbled across this video - today we got our renault master and can`t wait to start working on our home on wheels. i really like your interieur and the idea that both seats can be swiveled... i checked the link you posted for the swivel seats below, but it seems, that there are no swivel-plates to find on this site... so... may i ask, whether you remember, which swivel plates you used AND if it's possible to swivel the seats with the doors closed?! i saw various videos where swivel plates were installed, but you can only swivel the seats when opening the doors - which makes it a bit unhandy in my opinion -.- thanks for a short reply in advance and best regards from germany :)

thanks for showing nothing

This guy doesnt know what he is doing

what was the point of raptor liner compared to not having it?

Ciszko wchodzi bieg 1i wsteczny, linki Ok są pytanko czy to lewarek ?

Jak wymienic lewarek zmiany biegow . Czy jest może film

Thanks great video

A jak zdemontować prowadnic szyby

Ciszko chodzą boczne dzwi co poprawidz

Bravo

Thank you for video, i have to do it as well in my van 🤝

Grat video - does that help in the door being slightly misaligned? Mine (Renault Master Mk3) is about 5mm lower than it should be!

Was it necessary to redo any blind rivets with a pistol?

Excellent video just the job nice and easy to follow perfect.👍

Too video

Hi, I'd like to know how to replace the automatic electric lever...

Thanks! Looks easy enough, I will attempt it on my Peugeot Boxer!

Fantastic video. A garage quoted me over 70euros to take off the whole wing mirror and replace this part. Ebay 12euros delivered to France from UK with 2 spare bulbs and 4 mins of your video and I now have a sparkling new light on my not so sparkling NV400. Thanks again.

No need to remove the inner panel

There is one big mistake the layout - the water tank should be mounted on the lower shelf instead. Big heavy items like that should always be mounted as low as possible as it will otherwise negatively affect vehicle handling.

Just about to do this repair on a Fiat Scudo. Thanks for the guide. Often the reason the roller wears out is from greasing the track. It may appear to make it slide easier, but the grease also attracts abrasive grime which ultimately causes the roller to seize up. Then it wears a flat spot, the rubber wears through and the steel wheel starts cutting a groove in the track. This is the mistake I made! I'd suggest that the best thing to do is to simply always clean and dry the track when washing the vehicle. If the track is clean but the rollers are stiffening up, I've seen it suggested that a small squirt of silicon spray directly on the roller bearing will help, but also to wipe off any excess silicon immediately. Try not to leave anything left on the track surface and outside of the roller to which grit and grime sticks.

Model 2012 lock is different

Hi, how high would you say the standing room is in your van with the ceiling and floor installed?

Thanks a lot for that. Good job. I now know what to do, Cheers

Same issue as Artur... May be helpful to pop it in the description too? Can't believe I've been messing about with this for days because of that

nice FAQ! thanks a lot