Відео

I love how you say measure. Long A 😊 Great video thank you so much !

Don't forget to add oil.

Before I looked up how to make them I didn't know there was any other version than these boards here. I don't know what the "3 hole washers" is all about, but this is exactly the video I have been looking for. We always covered ours with conveyor belt rubber on the top, 2 washers a player and play to 21. Great instructional video man, I love it.

Excellent presentation on this machine

Does this also work for the hemi?

What is the white plastic tank underneath the driver's seat for?

u said something is in the bio

I have the same go kart but having a problem can you help?

It would have been nice if you showed flipping the axle. Mine doesn’t have cut outs at the bottom and I’m struggling. 😂

Did your unit leak gear oil when it set from the axle before and after my the I got from said he put two on one side I think it has a grove in the the axle. But the engine lock up only turns to 11 and back to the same spot thank you

Hi, Thanks for the nice video. Very informative and clear. Did you ever make the other video on the replacement of the Tine seal that you mentioned at the end? On my Vertical Tine Tiller, one of the Tine Seals is leaking a bit and I was wondering if it is something I could do. If I see how it is done, I normally can do it but right now I am not sure where to start and How complex it is. Thank you again.

My Hustler Fastrak 48 has a Honda GXV 610 engine that has less than 100 hours. It starves for fuel when it gets hot and quits running. The air cleaner can't be removed to service the carburetor because the steel square nuts spin inside the plastic fan cover and there's no way to put a wrench on them without destorying the fan cover. Honda used to build quality products, now they build plastic disposable junk.

Dude I have an old troybuilt I need to remotor,,, which HF motor did you use and di you have problems with the shaft being to long?

Was there a reason why you switch to the 420 chain and not keep it to the same chain that go-kart originally had? And was that a 530 chain?

Recommendations for a burr in the axle? best material to file it out?

I have the same go kart and question can you help me out?

Yup, that wheel came right off the axle shaft. 😆😅🤣🤣🤣🤣😂😀

The original engine on mine is 8HP. The only Predator engine that would work is the 212 cc engine which is about 6.6 HP. Would that be big enough? I’m thinking I should go with the Kohler Command Pro because it’s 9.5 HP. Just a tiny bit bigger

So satisfying man. Unreal work

Your video was very professional and I learned exactly how I will take care of mine. Thank you!

Excellent presentation, made it look pretty easy. I'm doing the same thing but removing a Kohler K161T. I'm sure it's not going to be as easy as you made it look ! Keep up the good work and thanks for the video.

Awesome video. Thank you!

Thanks for the video! I have the same tiller with the same issue.

666 likes not today devil not today had to add my one like

I would love to purchase one lmk how pls

I got the same go kart i put a Polaris trailblazer 250 2 stroke engine on it

I just picked up a troy Built tiller like yours but no electric start. It was a free barn fine. Believe it or not it had the original HH60 Tecumseh 6 HP engine. I looked it over. Low compression. So i replaced the head gasket , oil and tinkered with the carb. The old girl runs like new. Amazing.

Hey bud good video, I have a question, on my Troy built tiller I have a oil leak on the bottom of trans where the low and high range linkage is there also a seal there ? Thanks

What part number sprocket did you use? I got a Trailmaster 150 and I’m using the same set up. As you at 4:20 cc predator motor. I did everything you’re doing I just can’t find the sprocket.

When you removed the governor arm, how did you get the throttle linkage to work again?

I have a Tecumseh HS50, it appears to have a camshaft pulley for reverse. Is this how this old engine was set up? Or did Troybilt change the forward and reverse pulley design? Great video bro

Howdy! Thanks for the video. Ive followed your video and installed a new predator engine. Im running into an issue where once i dig the tines into the soil, the pulley seems to spin in place, lots of smoke from the burning belts! Is this simply that i havent tightened the pulley onto the crankshaft enough or do you think i have a different issue? Sorry, im very green at working on this stuff.

Did I miss the part about the gearbox ? How fast does it go?

How much for a build like this ?

Tilled the sandy garden once this year and when I went to do it again nock nock nock and bang after 40 years the 8HP sent the rod threw the cylinder so I bought a replacement listed as 7 HP and when it came it was 6.5 so I put it on and when I went to till I would dig in 5" and it would stall out so I have been trying everything like changing the pudding in the gear box and putting some lube in the dry tine gear box but still it stalls seems like a lack of balls but watching this video it never dawned on me that there is a low oil shut off that the dig angle might trigger so thanks for the video I am out to try it again.

im glad i found this video doing the same swap for a customer and just needed to know exactly what to do thanks so much for putting the video on youtube!!

How do you install a choke cable?

What size driven pulley did you use when buying the 40 series

Very nice sir! Well done... I am about to do this exact same operation. Thank you & am looking forward to this transforming overhaul.

did u ever put the seal in the tines

The 22 and 23 models have a ZT 3200 hydros. They have labeled it a commercial mower. Gots duel tanks now. I know I just bought one. Mine is a 2023 model. 7916.00 out the door price.

Good morning- I'm doing a similar build on my Chinese made knock off of the same go-kart. Would you be able to answer some questions? I'm stock on the axle portion of the build at the moment. Thanks. -dan

New to karting, is this an adult or more of a kids kart?

Any chance you kept the recoil strater pulley from the Troy Bilt? I have a real old TB but the recoil starter had broken on the inside and one dawg is missing. I have been unable to find any replacement for the recoil starter.

I’ve been using pine sole and it’s a good cleaner or dawn soap

Thank You for information and advice Well done video Keep them coming

Can you give me the model of your new engine? Got similar tiller without engine, would like to put a new one on it.

2 millimeters difference? How much is that in inches? I'm an American and don't know the metric system. Thank you

I have a 1975 Horse and the tines stop turning under a load you have any ideas.

I Wanna do this exact build I have everything just need the help how can I get your help with the exact details of this build