Відео

Wont work with the Hemi engine. The fuse box and cpu is probably 5 inches more forward. Plus all the other extra wires and harnesses etc in that area. My next attempt will be to take passenger wheel off and wheel well cover. Hopefully i can get it that way.

Thank you for sharing that video, I will be doing this same repair soon!

STUNNING

What about the light on other side

Bruh, you didn't put the cap back on.

Thanks for taking the time to produce this video. God Bless you.

Thanks for this video. I didn't know you could POP off that module and my hands barely fit in that damn hole in the wheel liner

Can you switch the bulbs to LED ones??

😘😘☺️☺️😊😊🎉🎉❤️❤️❤️❤️❤❤🎂🎂

Camera guy not too professional, needs practice.

Great video.

Is the beer a required as part of the procedure? LOL good presentation. I was done in a matter of minutes

whoever uses halogen still now is an idiot.!!! their so dark at night.. you need led or HID

my 2015 is ds3 light bulb

Easy until I got to the actual bulb which feels like it is glued in there. A little wrestling and busted knuckles and it’s out. Still way easier than the wheel well port

Mine was a real pain to get in .

My 2017 doesn’t have a removable cap, just that little soft plug Also can’t get that piece out of the way that you moved first

I had to use a long socket extension up through the wheel well and place it up above the connection to the bulb and pry down a little to where I felt it turn slightly. I then went back to the hood area and was able to use my right hand two fingers to twist it out. Putting it back in was a pain as well and I sure hope I was able to twist it tight because once again no way to get enough grip on it to feel it twist into place.

Currently trying this on a 2019 GC. I have access to the bulb now. Is it a quarter turn left or right to take it out?

You don't need to unplug the ECU it will shift over far enough while still plugged in. 2016 limited needed to move the coolant reservoir first.Otherwise good info

That just fucking stupid design

Dealership estimated $225+. I just did this on my 2019 Grand Cherokee, literally only took 20 minutes, including watching the video. This was the best video on changing the headlight I found. Thanks so much for saving me $$$$.

Ahole skipped the part where you have to take the knobs off in the filter compartment

This could not be less clear. Genuinely the worst tutorial for this I've watched so far.

mine just would not twist at all. 2014 model, like it's super glued in there. unable to remove burnt out bulb

Did this method and now my check engine light came on. Not sure what to do

Excellent! Thank you. I am not mechanically minded however your video has given me the confidence to have a go.

I must try this tomorrow after work. I'm hoping for the best. I'll let you know....

like. really good drone. goodnight! 🤘

Can't THANK YOU Enough for making this video !! Worked Great !!

Is it the same for HID lights

Thats highbeams not the projector

Okay so mission accomplished but ir took me around 40 minutes. Passenger side advice: don't bother removing the cap in front of the wheel arch, it's pointless and a waste of time. Pull the tab on the ECU and pull it up and out of the way. If you want to make it easier unbolt the water expansion tank and move this out of the way too obviously don't disconnect any of the pipes!) Reach and feel for the cap, twist it off and remove it. Now this is what this guy doesn't explain very well: You'll feel the back of the silver box ( the existing bulb) ignore that feel slightly further inside, you'll feel flat plastic pieces. Use your right hand thumb and push this tab down. You'll need to quite forceful, you'll feel it click down.then with your right index finger under the tab, push the tab on the other side up. You'll feel the bulb come loose and you'll sigh with relief. But your not out of the woods. Pull the bulb towards you and feel for the connector. It's a Jeep so they don't give you much to play with, the cable is short. Get your replacement bulb and attach it to the connector. Then spend 10 minutes fishing around trying to get the bulb in place ( pushing the bulb in whilst trying to twist the tabs). Once you think it's in the correct place, put your index finger on top of the far side tab and push down and the other side with your thumb push the tab up. Check your lights are working and replace the cap, your ECU and expansion tank. Then with your thumbs cut to ribbons, don't forget to thank me. Remember it's not the bulb it's the tabs either side!

Left out passenger side. I’m about to attempt this but can’t disassemble that corner for easier access

It's a big ass box where a regular light would be any answers I have a summit

Used this for doing the passenger side and then came back when the drivers side went out. Both times I didn’t realize/forgot that there were two little knobs you have to release to get the bulb free. I have a 2019 GC Limited X for reference. Don’t know if that’s how it is on all other trims but once I got that it made things go smooth lol

Is this for lowbeam?

What about the other side?

Good vid! I would not have thought to remove the air box.

❤😁

Who wants to do all that to change a fuckin light bulb? Fuck you Jeep!!

Did anyone else have their check engine light come on after changing the passenger side bulb?

Thank you I’ve been taking off the bumper

Very good video

Thanks for the help! Something not shown is you need to loosen the coupling on the air inlet pipe in order to remove it so you will need a flat head screw driver. Popping the whole filter housing out was also kind of hard, I really had to pull on it but it's been in there for 9 years now.

Thanks!

Took some finagling but I got it - not much room to work with

❤❤❤❤❤❤❤❤❤😂😂😂😂😂

Great video - I need to do this for my daughter's 2019 GC and it appears unchanged in design. I am guessing that the first step to removing the large Air cleaner hose was loosening the hose clamp? I know I'm late to the party :)

Great video, but it still sucked. They definitely made it much harder then it needed to be. Your video was a huge help though. Thank you for sharing.