- 58
- 312 796
Mic S
Приєднався 2 тра 2010
Chinese Diesel Heater New Controller Q & As
This is the "New Type Chinese Diesel Heater Controller" that now seems to be shipping with the Diesel Heaters. Since my last video in the functions of the heater I have been asked a heap of questions some of which I answer in this video.
My original video link
ua-cam.com/video/FxzUKhDeII0/v-deo.html
I will endeavour to make some more videos if more questions are asked and also a video on replacement controllers, and common problems through the use of the diesel heaters
Thanks for watching
My original video link
ua-cam.com/video/FxzUKhDeII0/v-deo.html
I will endeavour to make some more videos if more questions are asked and also a video on replacement controllers, and common problems through the use of the diesel heaters
Thanks for watching
Переглядів: 133 043
Відео
Diesel Heater New Type Controller
Переглядів 172 тис.2 роки тому
After installing my Chinese Diesel Heater I found the LCD screen was different to the common one shown on UA-cam. Instructions were not very clear so I went through all button combinations with help from the instructions I had to work out what buttons do what. While there is no clock display on this LCD screen, timers are quite accurate when times are set.
Wombat Friendly Waterstation
Переглядів 924 роки тому
Here are some modifications to our waterstations to make them more friendly for Wombats and other larger nosed animals. It creates a larger opening by angling the 90 degree bends and then carefully cutting off the fitting that sits above the water level, When trimming the fitting make sure your saw is square to the pipe horizontally and vertically. Ensure all burs and any sharp edges are remove...
Installing and refilling your Waterstation
Переглядів 524 роки тому
How to fill, install and refill your Wildlife Waterstation with some handy hints
Wildlife Waterstations A Z of Construction
Переглядів 234 роки тому
Building a Wildlife Waterstation Tutorial from PVC water pipe. You can use either 100mm sewer pipe or 90mm storm water pipe. You just need to be mindful of the order the 90 degree bends go together. PVC cement will be secure after 30 seconds but it is recommended to leave for 24 hours before filling. Please remember to remove stations once they are no longer needed and keep them clean from slim...
Hypercube X Axis Issue
Переглядів 1075 років тому
Building a Hypercube 3D printer and having issues with the X axis. When I command the X axis only to move it also moves along the Y axis. I have the bushes on the aluminium tube moving freely without binding and have checked all pulleys to make sure they are not binding anywhere but still I have this issue as can be seen in the video. I have managed to improve the performance from my initial tr...
Bass Point
Переглядів 187 років тому
Rebuilding a Scrab Quad with APM2.5 and Gimball. This is the first test flight with the gimball, it still needs some fine tuning and failsafes all dialed in for reliable flights
Dapto May 2017
Переглядів 487 років тому
Just a boring video of some laps at Dapto Chasing and being chased by Chris's Quad. Haven't flown for a bit so am a bit rusty
Illawarra Gyrocopter
Переглядів 1607 років тому
A Gyro-copter flight over the Illawarra, Knights Hill, Minnamurra Rain forest, Carrington Falls, Kangaroo Valley, Foxground, Werri Beach, Kiama Coastal Walk, Kiama, Shellharbour and Windang
Building a Slim folding Saw Horse
Переглядів 7327 років тому
I gave my last sawhorse to my neighbour so need to make some new ones. The storage area was limited so I made this pair of slim folding sawhorses in about an hour using 70x19mm timber, gang nails and a couple of hinges. Each sawhorse consists of: 1xtop 70x19x700 1xtop 90x19x700 4xlegs 70x19x750 2xbraces 70x19x700 4x gang nails 6x 30mm wood screws 2xhinges and screws 1 short length of rope
New Flying Site
Переглядів 288 років тому
Trying a new flying location with heaps of trees Need to get the mobius tilted up for a better perspective A promising site
Bass Point
Переглядів 88 років тому
Got the Mobius out of mothballs and tried to get some footage following a wing. Harder than it looks. Top day for a fly though
Mic's CNC First Cut
Переглядів 569 років тому
Our newly constructed CNC machine using plans from buildyourcnc.com Geko540 controller Nema24 steppers Mach3 Cut2D 4 Axis X&Y axis belt driven Z axis Trapezoidal Rod Dell Laptop with Parrallel port
Barracuda 10k
Переглядів 1,1 тис.9 років тому
Another test of Barracuda10K V Hydrochloric acid. This test is over several jobs and different bricks so is quite comprehensive. The information I have received from the distributors of B10K is that it dissolves 10x more mortar than HCL but as can be seen from the results of this test, it has not been the case on these samples.