Відео

Will a trimmer damage the edging

It's from the piston rings

Why wouldn't the flat edge and spikes go on the inside of the circle?

Good product but very expensive

Can you install that so the bottom is on the inside? I’d like to put it the opposite way and then cover the bottom part with mulch.

I’ve got these. The only downside is they’re not very lawnmower friendly when you’ve got corners as the lawnmower can’t get into the round bends Easy but they do look great but it just means you have to get the strimmer out to cut the tight corners..

I purchased this kit and sent my results back in and haven’t heard anything in 7 days. Not sure if I did something wrong. I sealed the kit and placed it in the post office drop box.

It's still $10 for 4 feet. I think it's a cheap price to pay for a quality product that lasts long.

Why not put the stakes on the bed side, so they can be covered up by mulch?

Thanks for this. We're going to be putting a 12" wide border around the base of a sculpture on a plinth in our side yard. I plan to dig a 3" deep square trench around the bottom of the plinth, line with weed-proof fabric, then use this border with the nails on the inside, in a square, then fill with white rocks. Can this be done with this type of border? Could I just cut where I want each corner to be?

The flat edge and spikes goes on the inside

Will these work with a straight edge bed if I cut the corners at 45 degrees

Backwards, no?

Great tips there thanks a million - especially about nailing them in only half way so you can re-adjust everything!.......By the way - I'm noticing a good 'ol Irish twang there - whats the craic there? 😀

I would have flipped it and staked inside the bed, then cover it with mulch. Because it's ugly.

it says it only bends 70 degrees having fitted it do you think itll bend to 90

I think its the seal between the engine and the coil, check this video (how to replace a leaking oil seal generator)and (how to replace a leaking oil seal)

Would this look weird on a steep hill since the lines in the segments would then be angled? Great and useful video. Thank you.

you put them in backwards

What tool did you use to cut through the rubber?

Wow thats Smart however you have to be careful enjoy 😮😮😮😮❤❤❤🎉🎉🎉❤❤ ...

Was able to find this at Sam’s club for $7/ 4 foot section. Brick tone.

Why does everyone install the stuff backwards? The stakes should be on the inside.

Outstanding. Great product demonstration.

I’m trying to install this product in a circle but those little thingy broke thru the border how can I make it to stay together I don’t mind if it has a little separation but I need it to stay connected help

Breather tube from the valve cover freezes in the cold. Crankcase cant vent and as pressure builds it pushes oil out the seals. Just take the little rubber hose from the air box to the valve cover off

Have a child to hold the phone.

I also have a Firman 3650 I bought at Costco. It worked great here and there for 2 years and then mine started leaking oil from the same place. Did you ever figure this out?

I like how the tutorials back 4 years ago or more were low quality,most people don't lie about it,it doesn't waste peoples time,made by a phone, and poor edit skills Wish I could turn back times to the good old days

Where did you get it?

Thank you for the video.

We live this , we use your method when we go camping! Thank you soo much, it lights our place really good.🙏

These do not work on my soil. I must have some clay or something under the ground, because my spikes just bend and warp as I put them in the ground. I've tried drilling holes in the ground, and that doesn't even work as I don't have a long enough drill bit for it to work with.

I have a firman 10,000 watt generator and leaking oil not sure from where. Only ran it twice so far break in period had no issues with load noticed oil dripped i thought maybe start with washer to oil plug

Why are the nails on the “outside?

It’s backwards and not lifetime

I decided to give your method a try since I didn't have the necessary pole to bounce my tire against. VIOLA! It worked. Thank you for this simple method of clearing water out of a tire, and I have a really bad back. I still managed.

When bending do u have to cut it a little without cutting it completely off?

The pre-stamped Holes for the Plastic Spikes are Filled In with the Thick Rubber too so I took a Perry Knife amd pushed thru each hole to make a + Plus sign and the Spikes went right thru no problem it also made a + sign in the Layer of Weed Lining fabric underneath so it went right thru that as well and straight into the ground in one ez step. I used a Rubber Mallet instead of a Hammer. Sorry about the Terminology this is all new to me lol..

I bought this yeateerday and was'nt sure how to Install it so Thank you for this. Being a single female I can do this myself now and don't even have to weed whack it. Win Win !! Thank God. I am learning so much info from these Video's. What a Blessing. Happy Fall Everyone ❤🙏 🍂

What is the best brand?

Good stuff, I liked the idea of mowing around it with no issues. I need to use on my garden bed so the mulch doesn’t run off with rain. Looks nice around the trees the way you designed it.

Frost heave EVERY SPRING...NAILS POP...(will definitely give you something to look FORWARD to EVERY YEAR)

This product sucks! The side pegs are near too impossible to get all the way in to connect and bring two pieces together. Good luck with any angle 110 degrees or less.

Great video and looks like the comments are great too!!

Use a few drops of liquid dish soap (like dawn or whatever kind you may use) in each pinhole before pushing in the pins it will be a big help to you on inserting the joining pins they will slide right in like a hot knife thru butter by hand with no fight at all :)

putting mulch on top of weed fabric will turn into compost/soil and new seeds will take root on top of the fabric.

Moves way to much with camera/cell phone got dizzy

Hi Qhat was the name of the garden edging that you used and what is it called

looks backwards