![G’s Moto Vlogs](/img/default-banner.jpg)
- 12
- 42 264
G’s Moto Vlogs
Приєднався 15 гру 2017
Hey welcome to my channel, I work on anything that has a motor!
Kawasaki KFX80/Suzuki LT80 Carb Clean
Hey guys today we will be cleaning this carb that has been sitting on a Kawasaki KFX 80 for a little while and bring it back to life.
Переглядів: 174
Відео
Motorized bike riding BBR Tuning exhaust
Переглядів 2 тис.9 місяців тому
Motorized bike riding BBR Tuning exhaust
Motorized bike revival
Переглядів 1,1 тис.9 місяців тому
In today’s video, we will be reviving my motorized bike that was sitting for over a year!
Kawasaki KLX exhaust install
Переглядів 858Рік тому
In this video we put a FMF power core 4 exhaust on my 2022 Kawasaki KLK 140RF dirt bike!
How to install a BBR Tuning billet aluminum performance head
Переглядів 4,9 тис.Рік тому
How to install a BBR Tuning billet aluminum performance head
How to install a pull starter on a 80cc motorized bike
Переглядів 22 тис.Рік тому
Here’s the link for the engine a.co/d/g2p1Shz and here’s the link for the pull starter a.co/d/isaI14B
BBR TUNING Exhaust after almost a year of use!
Переглядів 4,4 тис.3 роки тому
BBR TUNING Exhaust after almost a year of use!
The pipe sounds good and I like unlike the mz65 clone....its not usually on the same side as the fuel line and carb
Instead of cutting your plastics you could have mounted it from the inside of the fender and the plastics will go right back
If you do that the exhaust will not be straight because of the fender plastic
Very nice, I used to clean carbs by hand....
Thank you
Motor 80 cm?
It says that when you buy it it doesn’t have any markings on the engine.
Nice build bro do you have any more plans for it?
Not sure yet but I have some ideas.
Wear is the clip, drop it to 2nd notch from top of needle to lean it out some, but your gonna need a smaller jet, way to rich 👽👍🏻
Ok thank you for the tip I recently bought some jets so I will make a video about that soon.
It's Alive, These little engines are Tuff an Fun 👽👍🏻
You got that right!
Ya dawg!!! Freakin sick!! Thanks for making a follow up on the pull start
lol, sounds like world war - typewriter
No wonder it would not start how much oil in petrol lol
that looks loud
Thanks
Wow,does that exhaust have a healthy crackle.I've been given lip for suggesting this before as they say,"Oh,that'll weaken the pipe"...Drill through your tension mount and put a hardened screw through into the frame.I'm talking 1/4-inch.Not a Bolt as they thought.It'll keep the tensioner from twisting into your spokes as easily.The engine mount bolts are 6mm which is...?Happy Trails.
Yes I have thought of doing that just haven’t gotten time to do it. Will probably do it in the next video.
using a two bolt tensioner is way to evel knievelish for me , get a arch type tensioner , its safer ?
I did have one but it broke so I took the speaker from there and put it on the stock one instead of that plastic wheel.
How do you like it?! I lost power going uphill on a 40t with a F2.
I love the sound of the pipe but I did notice a very tiny loss of power but I have to mess with carb and fine tune it and it should be better.
what engine is that
It’s an 50cc/80cc motorized bike engine you can buy them off Amazon or Ebay I have a link to one of them in another video.
GREAT VID
Thanks appreciate it
It sounds good i wanna see it in motion
Video coming out soon
Когда кататься?
Brakes ?
What about them?
That pull start is sick, and that exhaust sounds badass. I just greased up my chain couple days ago. I gotta start filming more too. Nice video!
Thanks man 👍🏻
Black is one of the only colors that dissipates heat,not hold it in. Someone mislead you on the color,so go research it better for yourself. Most older a/c 2-strokes were painted black for this reason ,,
hey a question on which website did you buy this exhaust?
I bought it on the FMF website but you can get it on other websites I just prefer FMF’s website
@@gmv762I can't find them on the fmf website
most of those gaskets are crushed to provide a good seal and really shouldnt reuse them after theyve been crushed once. obviously you can but they are cheap enough to just replace. AFAIK being a non expert and could be completely wrong. felt i should say that.
couple questions. Did you need to use the large "spacer" that was in the bag? Did you use any type of silicone grease to slide it onto the header pipe? Thanks
Yes I used the spacer that came with the exhaust and I didn’t have to use any type of silicone or grease everything just slides on
hey a question on which website did you buy this exhaust??
Building one now problem throttle cable to long
You can trim it but it’s better to buy a new cable the right length
@@gmv762 yeah ik problem is I can't lol
Brrrraaapppp 😮sounds better than stock
I use permatex ultra to black or gray best stuff out there.. Usually use the gasket again keep up the good work 👍🤙😎
Thanks 👍🏻
Bye bye pedals 😂😂😂
I would feel goofy having to run and jump on your bike just to start it
Why no peddles
The pedals broke so I decided to do this instead
Not legal at all it needs pedals if not it's considered as a motorcycle you'll need a license and all to even ride it.....that white smoke means your engine is flooded or oil is burning
I have a little white smoke so how do you fix that problem.
That’s fine it’s supposed to have smoke coming out the exhaust because there is oil in the gas. Mine has more smoke coming out because my ratio is off.
@@taurianharris9985 you can't 2 strokes smoke see all of em smoking just a dummy comment
The scooters are not required to be licensed with the state (because they are considered motorized bicycles) as long as they are under 50cc's in size, are not capable of going more than 30 miles an hour on level ground, have less than three (3) gross horsepower, and have an automatic transmission.
Calm your tits mister two first names
its still on amazon😂
wht eng u running?
It’s an 80cc engine an I have a link to it in my video about the pull starter
@@gmv762it’s a 66 technically
drill a hole in the tensioner put a sheet metal screw so it never moves and for the muffler gasket use a highlander 2002 o2 sensor gasket.
I LOVE THIS:)
I see your using a metal chain tensioner pulley wheel instead of the plastic roller shit
He must know a guy who knows a guy 😷👍
Nice job.Nice bike.
Thanks
Fuel filter is on wrong.
this is so cooollllll
Monster can is cool touch.
Thanks
Ever think about running that Ms clone pipe? They look and perform better I've heard
Yeah I’ve heard mixed reviews about it but there’s a video by BikeBerry and they review different types of exhaust and the F2 thruster did the best so I went with that it has better performance.
Nasty jack pipe with silencer ☝️
I hate all the spooge from the break in mix...
Yeah it’s annoying
Hey man how did that chain tensioner work out?
It works good it’s the stock chain tensioner but a different wheel and it haven’t given me any issues
@@gmv762 I've been looking into one of those wheels like you have, I was able to eliminate the tensioner from one of my bikes but not the other, I've been experiencing some of the same problems you described.
Mine should be here in a few days
Nice 👍🏻
@@gmv762 it came and I put it on but it is faster with the exhaust I had on it so I'm selling it to a guy that I'm putting a motor on his bike for him
Nice brother. I love how you did away with the pedals. I find the pedals get in the way of my turns and I would love to get rid of mine. My only concern is getting pulled over. Nice ride and explanations.
Have you not seen how ridiculous someone looks when trying to start one of these bikes without peddles?, it's really funny to watch, lol.
OMG YOURE SO COOL
I will be doing another video soon on the bike
sounds good way too loud imo
I bought my pipe to piss off the neighbors
Nice! Lol, my neighbors hate my expansion chamber, oh well.. Unless a person actually rides a motorized bicycle for the first time, they have no clue how fun they are..
Yeah
Yeah till you wreck it