Відео

10year have passed, do you still have the skid, if so did it last, if not still on this set up, how long did it last for you, did you end up changing the spacing/gearing,

Pink strawberry milkshake looking oil is an example of contaminated oil. It has water in it, and needs to be changed. The oil level is also way over filled. Two small plugs on the side of the tank, by the back wheel, is the max fill level for the 610.

Fantastic little machine. The 14hp can do a heck of a job. I moved a 100 yds of dirt to build a berm at my office. Built like tank and very simple to work on. Be careful, no brake!

Beautiful project!! Great job

How much does a job like this cost ??

I believe I have the same machine, no serial number plate. Purchased a few months ago and it doesn't want to turn without stalling the engine. It has been retrofitted with a 22hp Kawasaki. Any help would be greatly appreciated.

Would this be able to handle asphalt millings for driveways

Glenn my variable dive is leaking and won’t close against the belt . I want to eliminate it and bolt the to halves together is will this work and is this what you did to yours?

I always learn something from your vids. Thx!

Thx very much for the vid.

Glenn, you listed the stub shaft in the list of parts. Is this something you added to motor afterwards or did the Vanguard come with the stub shaft on it?

What is the name of the website you found the jackshaft bearings?

Did you stay with the 14koler? How much can it lift?

Thank you

Hello , my name is Dave and I need some minor wiring work done on my S250 which is in pretty good condition and I believe I’ve done all the troubleshooting and have the problem figured out, but now I need someone to confirm that I’m going in the right direction and possibly help me with the wire repairs as well because wiring is not my strong suit. The wires in question are enabling my brake solenoid to lock up on me every 20-30 minutes of run time and stooping me dead were it happens. You can hear the magnet snap up into the hold position and I believe the damaged wires are also draining my volts & dropping them down in between uses. I also live in Massachuttes about 20 minutes south of Boston in Weymouth right off the highway. I will pay you well for your time & cash money too. I am a bit reluctant to sent it out to Bobcat again because they charge you $3000.°° or more just to look at your Machine & I’ve already been let down recently and would prefer to have someone like yourself work with me, I really can’t see it taking more than a few hours but as I mentioned I really want confirmation that I’m doing the repairs correctly & getting the job done properly too. I don’t have any problem with cash & if it does only take a few hours I’ll pay you for the day regardless but I have a trust issues mainly because I’m to trusting myself. If you wouldn’t mind giving me a call at (781)985-0428, & ask for Dave I will make it worth your time. I drew up a schematic on a piece of large art paper that I draw my designs with for my landscape designs & hardscape projects that I’ve been doing for 25+ years now so it should be pretty easy to understand and I have the service Manuals as well along with a large tool selection. Hope to hear from you & thank you. Dave B.

great video my friend good job fixing it up

That oil has water in it

The old ones where so small but that is what they where ment for they wher built for cleaning turkey pens

The hydronic lines are where it gets expensive i always say om going to buy the stuff to make my lines and never finger what to buy

Restore never compleat with tractors

Nice, looks pretty straight foward. Sadly I don't got a lift but just did a 07 civic manual clutch replacement on the ground. Sub frame had to come out for that job as well..laying on the floor sucks 😅

cuanto levanta en altura y en peso ?

All I can say is congratulations.. life is what we make it..

Does this machine have a reservoir?

These were good machines for what they were. Very cheap to rebuild and little to go wrong. i replaced a few lower jack stafts replaced my share the simple gear pump , fixed broken chains and yes rebuilt that 14 hp motor. Good fine

О май гад

I have a 371 with the Harbor Freight engine... I have logged hundreds of hours over the past 6 years. Runs Great, I have a battery so Key start. Best Little Bobcat ever...

I put a rack in 2000 civic ex. I did not have to take inner tire rod off. found out , by video Eric the car guy

does the filter have a reverse thread on it?

What's the filter number for a replacement

How much for the hot wheels toy ? and you can throw in any hot wheels you have .......... im thinking 10 bucks ....

Glenn what kind of hydraulic fluid is used in the model 444?

So, it's 2022 now, how is your little skid steer with the "re-power" holding up? I didn't see any new videos.

I think something worth doing, would be to throw a bigger engine in it.. if you could find the right one.

Nice video. I just bought a 1975 m444 being delivered as we speak. Is there a service manual or operator's manual somewhere? I know nothing about this thing and want to at least know how to change oils and filters. Thanks!!

After 20 years, you got 111,000 miles in it (1997 - 2017). I wonder why you have so much rust. I have the same car. This year 2022, I got 279,200 plus miles.

Any links on the engine. I just picked one up.. anyway better to message?

Excellent! I have an omc mustang and don't know where to buy this belt. They are close to identical. Mine was made during he 70's.

I have a melroe bobcat and im rebuilding it at the point to where im tryin to figure out where to fill the hydraulic up both tanks smell like old gas but look like hydraulic oil is in both

kohlers is china made

I need this for dog shit

Great work. Good to see one saved.

The little machine looks great, what seat did you use on your restoration?

planning on doing this, while watching i think i was happy that my car isn't optioned with power steering for the first time lol

Great 👍 job

ok

Nice job!

Awesome video man! Very specific on what needs to be removed sadly i had to do it with floor jacks haha😂😭

My hydraulics stopped working, don't think it's the pump, it has fluid, could you help me out. 74 m500.

hello