Delta PLC Temperature Control Using PID(with Audio Explanation in English)

[@consultor6sigmapyme]

Very nice explanation, this is very helpful for my proyect, thank you from Mexico!

[@muhamedsultanustajanov4686]

It was very useful explanation
Thanks a lot for being useful to humanity

[@FRO2010fuz]

Great class, congrats. Thank you so much!!!!

[@chandansuthar7107]

Nice Video, good Job.

[@rockgangadharan8531]

Nice video sir i have confused about s3 sampling time putting that one explain

[@ahsankaleem2640]

Hello dear sir i see your vedio very first time and i collact use full information frome your vedio pleas give the sum an other camands explanation of isp soft

[@opret2152]

Nice video, good job.

[@vcc8136]

Can you send link to download the document you used in this document

[@renatocosta7145]

Muito obrigado pela explicação.

[@jkeee1800]

Thank you very much sir

[@chickenz4604]

Hi Sir, Nice Video! I am planning to control Ph meter automatically. But I am using normal valve (On/OFF) for the base and acid valve. Is it possible to use Proportional control by varying the timer value? based on the difference between PH present value and PH target value

[@carloscantillano2418]

Thanks for the video, the MV output does not work.
the value is always MV=0
I am working in simulation mode

[@yeserakkad7718]

good job keep going

[@mohamadajam937]

thanks for your feedback we appreciate it very much

[@SuperEngineer02]

my system 12SE PID Manupulated Output (MV) respon slowly where i need to increase the response time for increase/decrease of analog output. What i should change.

[@Ppkportalcom]

start from proportional gain
proportional gain decides how fast your system respond to a change. Both I and D help to make the response smooth
I makes slow and steady wheras D prevents overshoots and fluctuations

[@pravinranjane7268]

Can you explain PID instruction is used through WPL soft

[@prashanthh6984]

Hello sir I'm using for first time in delta plc in temperature and humidity chamber program are completed but only problem for not stability in temperature and humidity flectivation.any PID Value available...and pls send your contact details.thank you.

[@PIDOtomasyon]

Hi, urgent please,
is Dvp 14SS-2 support PID function?
because not working PID_WM out. I try every thing, but not...

[@Ppkportalcom]

14SS2 supports PID function

[@paninivitor]

I have a DVP-14SS2 working with and extention DVP-06XA and beggining with a digital button i need to send 20mA in the CH5, the Analog Output.
How can i make this?
tks

[@Ppkportalcom]

Use instruction " TO " to transfer values to analog channels

[@Eletricacom-vn2qu]

Bom dia professor, tem como controlar em PID duas válvulas solenóides uma controla a abertura e outra o fechamento

[@Shahidhussain-jj3ej]

hi
how can i pid 2 rely like y0 high temp and y1 low temp
like forward reverse motor control valve
plz helpe me

[@sumeetmahale3235]

How to set output value.. like u hv set pid output value 4000 how is set?

[@Ppkportalcom]

in the S3 + 6 register you can set the upper bound limit for the MV(Manipulated Variable - PID output)

[@sumeetmahale3235]

Thnx sir.. i hv try... To insert expantion module card for analog output... Bt there is no output genrated from pid output...

[@cervejariauffenberg3252]

Please do not understand how to configure S3 to work with autotune. literally, what should input S3 look like?
Thanks!

[@vaishnavielectration]

Sir i m unable to find mv on my pc

[@syeswanthkumar412]

I have a DVP 14ss2 PLC and a delta temperature controller could u please help to the wiring for PLC and controller , communication between the PLC and pc, controller thanks in advance

[@Ppkportalcom]

Can I know the exact model no of temperature controller

[@syeswanthkumar412]

Dtb 9696cv

[@Ppkportalcom]

does your temperature controller have rs485 interface

[@syeswanthkumar412]

Yes

[@syeswanthkumar412]

Please help me to sort the problem

[@lccora]

I did the same program in SS2, using the simulator, and direct in PLC, but no have result in PID block, no show nothing in D200. and in the monitor, show only in D2000, D2012 and D2013 change 0 to 4000 very fast. whats happen?

[@lccora]

You commented "Also dont forget to use Retentive range for Settings(s3) of PID", need more some instruction to try?

[@Ppkportalcom]

for PID I recommend to try with real PLC rather than simulator

[@Ppkportalcom]

share screenshot of monitor values from d2000 to d2019
hope you put d2000 in S3 of plc block

[@lccora]

ua-cam.com/video/fzBb3jybwCo/v-deo.html Please, see my screen.

[@atharmay]

Hi dear... I tried with real PLC but same problem coming with me plz suggest possible causes.

[@vaibbhavgodse3702]

what is command for ADC for delta PLC FOR temp controller

[@Ppkportalcom]

For making analog to pusle use GPWM instruction

[@udaykulkarni8989]

Can't see vodeo properly
Onlt green screen

[@bhavdipbhal1807]

Any one used DPID ?

[@xeroki]

AAAAAAAAAAAAAAAAAAH AGORA SEM TENDO MANITO KKKKKKKKK

[@xeroki]

MUITA MACONHA