Hoverboard motherboard hack how to hack Hover board motherboard Firmware STM32 BLDC motor cart STM

Поділитися
Вставка
  • Опубліковано 26 лис 2024

КОМЕНТАРІ • 123

  • @Fatpumpumlovah2
    @Fatpumpumlovah2 11 місяців тому +2

    2X tilt sensors for each side can be mounted on top of eachother, cables lengthened and can be mounted anywhere on the Trike/Kart on a pivot and angle can be changed via regular throttle cable to tilt forward.... break cable can make tilt backwards for breaking or reverse... then no hacking will be needed to the board.

    • @magnusviklund5877
      @magnusviklund5877 10 місяців тому

      Have you seen that work well anytime?

    • @jonanbahnsen3935
      @jonanbahnsen3935 10 місяців тому

      That's an interesting idea. Diffently gonna try that :)

  • @MamasFood-ex3sm
    @MamasFood-ex3sm 14 днів тому

    Nice technical sharing

  • @gycooking1320
    @gycooking1320 4 роки тому +2

    Well-done for effort and well explained, it is really very useful information

  • @atiflatif236
    @atiflatif236 3 роки тому

    It's all about technology things which I don't get ,but do get my thumbs up for the job done

  • @mehjabinkhan3609
    @mehjabinkhan3609 3 роки тому +1

    Very nicely explained 👍

  • @mkr32
    @mkr32 4 роки тому +2

    nice work

  • @przemos7816
    @przemos7816 3 роки тому +1

    Where did you connect the potenciometers to ??
    Rx and tx pins on left wheel ?
    Or Rx on the left wheel and Rx on the right wheel? Thanks

    • @MKRCLabs
      @MKRCLabs  3 роки тому

      Ok next week In other video I will

  • @samirsuleymanov2099
    @samirsuleymanov2099 2 роки тому +1

    Huge thanks for the video! One general question, sir. Can I in theory use this motherboard to make a force feedback steering wheel for simulator? Usually, people use motor, but they use some other bldc controller and arduino leonardo. Can this hoverboard motherboard handle all of that?

    • @MKRCLabs
      @MKRCLabs  2 роки тому +2

      Yes possible it is other software but use HAL sensors and make connections for potentiometet

  • @taiwancowbei8857
    @taiwancowbei8857 2 роки тому +1

    Hi, just curious I have a different kind of hoverboard that comes with two motherboard for each wheel instead of one single big one like yours. Will I be able to do the same step as what you did or I will need to find new firmware for these different motherboards? thank you in advance!

    • @MKRCLabs
      @MKRCLabs  2 роки тому

      Different firmware

    • @MKRCLabs
      @MKRCLabs  2 роки тому

      Ok

    • @sarantisbalis7114
      @sarantisbalis7114 Рік тому

      Hi , I have the same model with the two motherboards. Did you find the "different" firmware ? or you did any progress?

  • @chitibusu
    @chitibusu 7 місяців тому +1

    Do you think we can use the motor controllers already existing on the hoverboard board? To bypass the hoverboard uC brain? Thanks.

    • @MKRCLabs
      @MKRCLabs  7 місяців тому

      Yes we can check my video hoverboard motherboard fitmware

  • @ecoegg4608
    @ecoegg4608 2 роки тому +1

    what type of potentiometer you use. what value? ,Thanks

  • @cookingwithmaageandvlog.
    @cookingwithmaageandvlog. 3 роки тому

    wow great engineer sir

  • @HoXDipannew
    @HoXDipannew 3 роки тому +1

    Awesome 👍👍👍👍👍

  • @pilottuan18tuoi77
    @pilottuan18tuoi77 3 роки тому +1

    Thanks so much 🍓🍓🍓

  • @DeepakChauhan-dp9zq
    @DeepakChauhan-dp9zq 3 роки тому +1

    Thanks for this wonderful video. I'm having trouble with the wiring etc. The battery wires attached to the board is cut off. When I try to attach it to the battery it sparks. I tested the battery with another board and that works fine. Can you gimme some tips? Also is it possible to have a chat with you? I need some more direction. Thanks in advance

    • @MKRCLabs
      @MKRCLabs  2 роки тому +1

      Ok i will check it

  • @matthewking9296
    @matthewking9296 3 роки тому +1

    What does each wire colour represent on for the potentiometer?

    • @MKRCLabs
      @MKRCLabs  3 роки тому

      1st Earth 2nd to board ( middle) 3rd +3.3 v

  • @simba8661
    @simba8661 3 роки тому +1

    Good

  • @misbahmujtaba7638
    @misbahmujtaba7638 3 роки тому +1

    Great

  • @ThePhannhung
    @ThePhannhung 2 роки тому +1

    Hello Thank you very much for the video, I am Vietnamese and would like to learn to repair balance bikes.I don't know if you can help me to repair the electric balance car circuit?

    • @MKRCLabs
      @MKRCLabs  2 роки тому

      What is problem in cat

  • @syedsaqib2661
    @syedsaqib2661 3 роки тому

    Thanks for sharing ideas

  • @coloristicartist8215
    @coloristicartist8215 4 роки тому +1

    Very good

  • @bluedeckelectronics
    @bluedeckelectronics 2 роки тому +1

    Good job!

  • @pilottuan18tuoi77
    @pilottuan18tuoi77 3 роки тому +1

    Dear Sir
    I have 2 question please
    1 ) Can we still reset to the normal setting program ( Orignal program ) ?
    2 ) Can we still charging battery by adapter normaly ?
    thanks

    • @MKRCLabs
      @MKRCLabs  3 роки тому +2

      Yes you can charge battery

    • @MKRCLabs
      @MKRCLabs  3 роки тому +2

      But original firmware required is avail able on github

    • @pilottuan18tuoi77
      @pilottuan18tuoi77 3 роки тому

      @@MKRCLabs thank you so much 😍😍😍

  • @noorbutt5534
    @noorbutt5534 3 роки тому

    Nice

  • @TechTed1
    @TechTed1 2 місяці тому

    Yesterday i destroyed one for parts i will not sugest people to use them they can backflip from that hooverboard

  • @usasat00
    @usasat00 3 роки тому +1

    What is the size of the potentiometer you are using?

  • @sayedme2uc
    @sayedme2uc 2 роки тому +1

    Can you advise. I am using stm32 cube programmer and st link V2 and upgraded the firmware connected, disconnected st link however, couldent connect

    • @MKRCLabs
      @MKRCLabs  2 роки тому

      Reseting required after upgrade or first connection thats why connec and reconnect

    • @sayedme2uc
      @sayedme2uc 2 роки тому

      @@MKRCLabsI did disconnected and reconnected the st link after firmware upgraded, still no connection

    • @MKRCLabs
      @MKRCLabs  2 роки тому

      Stm32 original devolvement board or bluepill ebay

    • @MKRCLabs
      @MKRCLabs  2 роки тому

      I will try on my hoverboard with different st link

    • @MKRCLabs
      @MKRCLabs  2 роки тому

      Install zadig usb driver it will solve you problem

  • @mahjabinkhan3389
    @mahjabinkhan3389 3 роки тому

    Nice 👍

  • @harilal7406
    @harilal7406 3 роки тому

    Nyc

  • @chrisj111706
    @chrisj111706 3 роки тому +1

    can we control the motor separately by potentiometer?

    • @MKRCLabs
      @MKRCLabs  3 роки тому

      It is possible if you use BMD ZS-X11B you need two controler with hover board controler I try it give problem during reverse/forward

  • @MonaLuso
    @MonaLuso 2 роки тому

    Hi
    I take of the two infrared sensores to put the motors running automaticly, but just one running, how can i put the other running too???

  • @Home_made_ch
    @Home_made_ch 2 роки тому +1

    Is possible to connect rc receiver instead of potentiometers?

    • @MKRCLabs
      @MKRCLabs  2 роки тому

      Possible

    • @Home_made_ch
      @Home_made_ch 2 роки тому

      @@MKRCLabs thanks, got all done already. As soon as get messages, started dogging all around and found how to do it.

  • @purafajro
    @purafajro 3 роки тому +2

    Hi! Is it work with normal ebike throttle ( with hall sensor ) ?

    • @MKRCLabs
      @MKRCLabs  3 роки тому

      Yes but only three phase bldc motor

    • @MKRCLabs
      @MKRCLabs  3 роки тому

      Yes works but only three phase bldc motor please confirm the voltages too

    • @purafajro
      @purafajro 3 роки тому

      @@MKRCLabs Thank you!

  • @hayaaliar6140
    @hayaaliar6140 3 роки тому

    Gud

  • @bahrulhuda5564
    @bahrulhuda5564 4 роки тому +2

    Can you control the Hoverboard using the Arduino joystick

  • @Muhammadismail5288-y7h
    @Muhammadismail5288-y7h 2 роки тому

    I have an issue while connecting ,though my St link upgrades but when my ST link upgrade ends , it says " ST link device lost when exiting upgrade mode "

  • @bluecavemen
    @bluecavemen 6 місяців тому

    What is the point of the firmware? Why can a receiver just tell the circuit board to go forward and backwards?

  • @manokhan4409
    @manokhan4409 3 роки тому

    Nice great great

  • @kitchenwithsoniakhan5190
    @kitchenwithsoniakhan5190 3 роки тому

    Nice a.h.g

    • @MKRCLabs
      @MKRCLabs  3 роки тому +1

      Delicious and tasty

  • @RamannaSacca
    @RamannaSacca 3 роки тому +1

    How to brake in full speed? Thanks

    • @MKRCLabs
      @MKRCLabs  3 роки тому +2

      Just rotate potentiometer or change rotation anticlockwise or switch off

    • @RamannaSacca
      @RamannaSacca 3 роки тому

      Thanks for quick response 🙂
      One more question, When I power the board on the wheel start spinning backward and keep beeping.Then I twist the throttle a little bit more then the motors go forward no beeping at all seem like normal but when released the
      throttle then the board keep beeping and wind backward again.
      Any solution for that? Thanks
      Note: used an ebike twist throttle for the Speed testing

    • @MKRCLabs
      @MKRCLabs  3 роки тому +1

      We are using two potentiometers one for speed and one for direction adjust the potentiometer in middle then it will not move backwards also stopped the beep thanks fo comments and subscribing me please share with your friends next week I will upload an other video in that it is fixed with cycle and speed control machnism also different

  • @evaldaskum6086
    @evaldaskum6086 Рік тому

    Hey i want to ask you i did with remote but wheels always spinning when i turn on remote control but dont do enything only on what could be the problem? Pss: i have to remove and insert again battery to stop it and turn off remote. Thanks if you could help 😊

    • @MKRCLabs
      @MKRCLabs  Рік тому

      Use different hex file from github

    • @evaldaskum6086
      @evaldaskum6086 Рік тому

      @@MKRCLabs nice thanks but could you help how to turn left or right? back or forword it gose but left and right not😊

  • @alfankosh1
    @alfankosh1 2 роки тому +1

    i really need help i have 2 st-link v2 wen i connected to pc the pc foundet without problem but the STM32CubeProgrammer and STM32 ST-LINK Utility didnot found the st-link v2 what ido?????

    • @MKRCLabs
      @MKRCLabs  2 роки тому

      Update v link 2 software

    • @alfankosh1
      @alfankosh1 2 роки тому

      @@MKRCLabs how i update if the software didno found the stm32

    • @MKRCLabs
      @MKRCLabs  2 роки тому +1

      First update st link

    • @MKRCLabs
      @MKRCLabs  2 роки тому +1

      2nd after connection disconnect and reconnect this is solution i secially explain this part in video

    • @MKRCLabs
      @MKRCLabs  2 роки тому +1

      If still problem use other way create hex file and try with st link v2 no need st cube programer

  • @esmamewaticartoon
    @esmamewaticartoon 3 роки тому

    Best

  • @SherHameed-h6b
    @SherHameed-h6b Рік тому +1

    Sir ji min pakistan sy hun ap ki awaz sy lag raha hy ap pakistani ho help me sir

  • @pathfinder2reality
    @pathfinder2reality Рік тому

    Can a hoverboard that was using 14 cell, 24V battery use 20 cell, 36V battery?

  • @antoonsorg
    @antoonsorg 3 роки тому

    How to flash ARM STM32 RCT6 99JH 98 , keep error can not connect to device. But i can upgrade the firmware st-link V2. Tried stm32 cube programmer and the older stm32 utiliy program.
    Same error.

    • @MKRCLabs
      @MKRCLabs  3 роки тому

      When you receive this message disconnect and reconnect again if you watch the video I explain clearly when this tricky step is required thank you ☺️

    • @antoonsorg
      @antoonsorg 3 роки тому +1

      @@MKRCLabs
      I did but it did not make a difference.
      Just hear hoverboard beeps.

    • @MKRCLabs
      @MKRCLabs  3 роки тому

      Check your st link v 2 good or change it and try

    • @antoonsorg
      @antoonsorg 3 роки тому

      @@MKRCLabs
      Checked st link v2 three times, maybe the 4 pins wiring hoverboard should be different its a chinese stm32 imitation mainbord(red color)

    • @MKRCLabs
      @MKRCLabs  3 роки тому

      @@antoonsorg check the power with meter if already you connected the power also what about switch be care full for power supply cables can you watch again video it is with full details for connection

  • @mharoon5741
    @mharoon5741 Рік тому +1

    Hi
    I m
    Haroon from Pakistan
    You from we’re plz?

    • @mharoon5741
      @mharoon5741 Рік тому

      Can you give me Whatssapp number please
      I want talk to you

    • @MKRCLabs
      @MKRCLabs  Рік тому

      Yes friend

    • @mharoon5741
      @mharoon5741 Рік тому

      Thank for reply

  • @niranjanbiswas8480
    @niranjanbiswas8480 2 роки тому

    Sir my hoverboard red light is blinking 2time how to solv it?
    I am so thankful to you if you guide me

  • @lorobal
    @lorobal 2 роки тому

    Hello friend, I would like to know what I have to modify in the file to remove the speed limit

  • @dannydelacruz5309
    @dannydelacruz5309 2 роки тому

    hey thanks for your video. how can I downlod d
    the sorftware?

  • @huzaifakhan5024
    @huzaifakhan5024 3 роки тому

    ✔️✔️

  • @SherHameed-h6b
    @SherHameed-h6b Рік тому

    Bhai jan ap pakistani ho

  • @muhammet6152
    @muhammet6152 Рік тому

    I have a controller using 72v 45a stm32 i want to increase its speed how can i do it

    • @85daniels
      @85daniels Рік тому

      is it Votol ?

    • @muhammet6152
      @muhammet6152 Рік тому

      @@85daniels no lingbo

    • @MKRCLabs
      @MKRCLabs  Рік тому

      I will heat up this hoverboard motor not design for high speed any how run with out Hal sensors feed back

  • @colladron
    @colladron 2 роки тому

    Se puede controlar por RC con receptor ppm?

  • @malikfurqan9880
    @malikfurqan9880 3 роки тому +1

    Can u fix mime also

    • @MKRCLabs
      @MKRCLabs  3 роки тому

      ضرور جناب sure

  • @p2ppapan735
    @p2ppapan735 3 роки тому

    Kordia

  • @fatimanoor9707
    @fatimanoor9707 3 роки тому

    A

  • @harizmator
    @harizmator Місяць тому

    Вы мне объясните какой дурак на видео на английском языке навесил заголовок на русском?!!!

  • @mustafacan3.4
    @mustafacan3.4 Рік тому

    hello bro i need your help on hoverboard can you give me a contact address please

    • @MKRCLabs
      @MKRCLabs  Рік тому

      Sure

    • @mustafacan3.4
      @mustafacan3.4 Рік тому

      @@MKRCLabs I would be very grateful if you give me your contact address.

  • @sabaadnan6586
    @sabaadnan6586 3 роки тому

    Nice