Failed LED tube repair with DIY Driver circuit
Вставка
- Опубліковано 3 лют 2024
- LED Tube lights should last a long time, but sadly this one has died 😢.
I wanted to see if it was repairable. Often it's not the LEDs that fail, but rather the driver circuit. In my case the LED strip was fine, but the driver was not repairable. So I decided to make my own LED driver circuit, based on a simple capacitor dropper circuit 🤔😉. I selvedged some of the components from the original driver boad. It's probably not worth repairing this cheap lamp, but I hate that so much repairable stuff goes in landfill. It's also rewarding to fix something that was broken, and then to see it coming back to life😜
Warning ⚠️ Working on mains voltage circuits is dangerous⚡️☠️⚡️.
Always remember to disconnect the supply before working on your circuit. Only work on mains voltage circuits if you feel confident to do so! These voltages are potentially lethal !!!
If you like my videos please consider supporting me🤞
/ myprojectbox
paypal.me/buddymel
revolut.me/roberteygb
#electronicscreators
#leddriver
#ledtubelight
#capacitordropper
I love the clay blob idea. I’ve not seen that before. Will be buying clay. :)
It's called BLU TACK and it has many different names in different countries. It can be white or blue.
en.m.wikipedia.org/wiki/Blu_Tack
This is so good to stop electrical waste that we have so much off, well done another good project cheers for the video
It's not always the destination that is important, sometimes it's just the journey.... Or to put it another way, it's just fun to spend time and energy to do a project like this, even if you don't need to.
Well done and please keep the videos like this coming.
Take care and stay safe,
Joe
I completely agree with you😉 thank you👍
amazing video tutorial boss... i have a lot of these lying around. i dont throw them out because i know its just a driver issue thats cheaper to replace or fix. glad this video helps with that.
I think it's a good idea to repair led lights because I find it's the drive that goes out in most of them.
Yes, and most of the time a simple capacitor dropper circuit is all that is required. You can also reduce the current to the LEDs to run them slightly cooler😉
I would recommend replacing the 100V smoothing capacitor with a 400V one so that it does not explode if your LED strip goes open circuit.
Yes ideally a 400V rated capacitor would be better, and the dropper cap could be x2 rated😉.( This would mean a much larger capacitor, and there is very little space)I was trying to reuse as much as possible, and salvage bits and pieces. The LEDs are in multiple series strings, several strings in parallel. So if one LED happens to go open circuit, There will be plenty others in parallel for redundancy. You might get the sort of cascade failure though🤔. I have seen many cheap LED lamps use this voltage clamping approach, to use a capacitor with a lower voltage rating.
Some times you don't have enough room to place the components.
You could wrap the broken length with painters tape to hold it till you open it.
This is a very good video and very useful
love that capacitor explosion at 4:57 💥💥💥
I guess the value of 1uF dropper capacitor was not arbitrary.
Yes I tried using different values of capacitor until it approximately matched the brightness level of the other lamp. The LED current is a bit lower than the original, so it will be better for the lifespan of the LEDs.
Afraid I can't agree with your statement that the LEDs are less susceptible to spikes from that capacitive dropper. When LED lamps first came out I experimented with a bunch of driver circuits, in order to add some bright LEDs to my garage door opener. I totally gave up on simple capacitive droppers. They all failed sooner or later by burning out an LED. Easily spotted by the black spot that would appear on the dead LED.
Yes you are right, and maybe I should of clarified what I meant🤔. "Cap droppers" are essentially high-pass filters, So any higher frequency switching noise and garbage, pass straight through. With just a single long series string design, one LED will become the weakest link in the chain, and take the entire light down. What I was trying to say, is that my strip has multiple series strings in parallel. So It can cope a little better with shunting out the current spikes. But you can still get a cascade type failure, because LEDs are quite fragile. It's not a good driver for noisy electrical environments.
i always cut the led strip into 12v section and power it with constant current step down converter, the driver in t8 tube is tiny and always fail(because leds have enough cooling to not fail unlike led bulb)
Thanks for your channel, lots of food for thought.
Kinda think you should at least refer to a mains safety video.
Folk starting out who watch this may not yet realize how much care is needed when dealing with potentially lethal voltages.
Just saying.
My first mains shock threw me (age 6) across the room. My heart kept going so I lived to enjoy a great hobby and eventually profession.
You are absolutely correct. I really should've included a "working with mains voltage ⚡️" warning. I have done this in my other videos. I will add it to the description right now😉.
The reason it's so fragile is due to the large amount of UV radiation that the LED's produce.
I know the old fashioned florescent tubes produced a lot of UV light, and it made everything plastic, brittle inside the light fixture. But I don't think LEDs produce true UV light. It might be "near UV" ,purple blue light. It's still very reactive, and perfect for stimulating the yellow phosphor, to make white light.
Danke für das Video.
Wie hoch ist die Spannung für den LED-Stripe? 325VDC? LG
60Vdc +
Wie kommt diese Spannung zustande?@@MyProjectBoxChannel
@@AmperekaeferDie Eingangsspannung fällt am 1UF-Kondensator ab, da die Last an den Brückengleichrichter angeschlossen ist.
Die LEDs halten eine Spannung von 60 V.
Ich weiß nicht, ob ich richtig übersetze😂😂😂
OK, kapazitiver resistance, thanks. LG@@MyProjectBoxChannel
@@AmperekaeferJa, es heißt Impedanz für Wechselstromwiderstand. für Dinge wie Kondensator und Induktor
LIKE👍 👍 👍 👍 👍 💯💥💯💥💯🤩🤩🤩🤩🤩
replace the LED with AC LED maybe
poor explanations