Under hood temperatures present a terrific challenge in a small engine compartment. Issues such as fuel vaporizing in fuel lines, rails, filters or pumps can manifest. Insulate headers, ensure cool fresh air intake, use extra electric fans etc. Keeping your engine running smooth on a hot summers day in Tucson will depend on temperature management. A cat appeared in one of your vlogs, tell us a cat story! Thanks Sarah :)
POR--15 makes a two part epoxy putty that cures incredibly hard and can be sanded and painted over for those small holes on the roof. I used it on a seam of a 68 mustang where I had to weld in a replacement inner fender panel 18 years ago. It was sanded smooth and has never cracked.
Lead for those roof holes might be the best choice. Low heat required and it'll take paint just like the steel. Kind of like those cars back in the 50's and 60's.
If you have anyone there in the Tuscon area that builds the old school "lead sleds" like the chopped and channeled Mercs and such, they probably know an old timer that works in lead filler (what they used before plastic filler). The lead is melted onto the metal so the roof wouldnt get nearly as hot so you could leave the headliner intact.
Massaging the tunnel for a wee bit of clearance rather than cut and weld makes it so much easier. You are killing it girl, so glad you have some help now.
Spot welding those roof holes might warp the roof. What about soft soldering the holes with an electric soldering iron. No fire risk, no warping, metal finish, saves a lot of work and possibly liner damage as well.
I liked the time lapse while hammering the tunnel. It clearly showed how much space you gained. If the headliner is damaged, it won't be your error. You're great at careful-ing. I agree about welding the roof holes, no choice.
Hi Sarah, a possible repair for the holes on the roof is to use 3M panel bond to fill the holes. Use a small Ball Pein hammer to indent the small area around the hole, and then fill it with panel bond.
So… I was on the road and got my new video notification and couldn’t help myself. I hit the next rest area to watch. Fabulous video of lots of work and success for mounting the new heart. Awesome soundtrack, too. Charlie is always a win. Thank you, Sarah. 👍👍👍
Doing the holes in the roof, I would not open a can of worms by removing the head liner. That material is from 1974 and is likely to tear. Since I don't know what you have for body hammers, use the round end of a small ballpien hammer on the hole and hit it with a a dead blow mallet to dimple it down then use JB Weld to fill it, then body fill over that. Panel bond may not be moisture proof but JB is. I would not use All metal or Alumalead, I've had cracking failure over a few years in the hot sun using those products.
The headliner being pristine should be preserved. Use metal or fiber reinforced body filler On the roof holes. It’s impervious to water infiltration. Of all the areas prone to rusting, the roof is the least likely. Especially in AZ.
Leading the roof is a beautiful minimum heat solution. Old school craft I would love to see you master. Sure you will get it done right no matter what path you take.
Use lead, or lead free solder to fill roof holes, no welding, just soldering iron. Also you can fill the rear quarter panel wilth solder and grind it. Old body shop technic so its all metal no filler.
I'm having a hard time deciding what's more impressive. All this custom build candy or the fact that Sarah somehow manages to keep her stylin nails intact.
Try a copper strip as a backing plate for the weld between the headliner and roof. Then you would only have to loosen the headliner rather than full on remove it.
@@SarahnTuned Have you heard of using lead as body filler? It’s the original body filler and superior. Yes, it will need to get warm to flow, but not welding hot 💁🏼♂️ options are optional 😬
Sarah. Look into the epoxy putty from POR 15 for the holes in the roof. It works great and I’ve never had it fail on many restoration projects. It gets hard enough to tap threads in it.
Back in the later part of the 80's, the Victorian police VL turbo interceptors & undercover VL V8's (in Australia) were retired from service which would come through our panel shop before getting sold off into public hands. We would fill in all roof holes from where the light, siren & aerial power cables went through. To save a few dollars, the dealership (Bayford) didn't want the headliner taken out so to prevent the headliner burning up from welding, we made aluminium discs to go under the roof & soldered the disc from the top of the roof. The low heat solder never burned the headliner & the metal roof looked like a file finished lead wipe.
You could use lead to fill those holes on the roof if you wanted. Since you’re not heating the roof just the lead you might get away with not removing the headliner.
Here we go again withTeam Sarah getting it done. Not settling, not compromising and no slack for our team. Love to see Charlie around as well as Angel. This is great viewing. We can always count on you to give it your all and you do! Press on Sarah!
Have you considered fixing the roof using lead solder? The holes are small enough that you could just use a big Weller 100W soldering iron like they use for stained glass. The solder melts at a very low temp, so very little chance of damaging the headliner.
Super work Sarah & Charlie! Another obstacle bites the dust! And another one gone, & another done, another bites the dust... "superb fab," just Fab baby... "just Fab! See y'all soon I am sure! CAUSE: IT'S SARA'S CHANNEL! J
Quick tip! For your engine hoist and jack too! When lowered to lowest setting and needs to be up a little high before contact or hoist action, loosen the release valve and put your foot on the base of the jack or hoist. Raise the hoist with your shoulder or raise the jack by hand and then tighten the release valve at the height you like! No pumping that dang lever all day!
VERY impressive engine install. PLEASE reconsider taking the headliner out to weld up the holes in the roof. Countersinking the holes and filling them with JB Weld will not only work, but save you a shit ton of time. Rock on, Sarah! 😁
You should check out this months issue of Canadian Hot Rods. There is an article on a 73 toyota celica with an LS swap done to it. Same flares and spoiler as yours.
Ingenious solution from Charlie on the wheel well strengthening. :) I was with you on the not hammering out the clearance, but it worked so well and doesn't look as janky as I thought it would. Great solution from whoever suggested it. :)
To weld the roof Method one Get some counter sunk screws that fill the hole with a little overlap. Remove the threaded part to just leave the head. With a screwdriver and hammer dent the roof slightly to ensure that there will be a small depression to fill when done. Tack the screw heads into the hole while pressing them down with a screwdriver. Use just a few tacks that will survive sanding. Flatten the weld and fill over with body filler or low temperature solder. Method two. Get some screws that head just pushes through the hole when forced. Insert them through the holes upside down so the thread sticks out. Tack around the screw head to weld it in. Grind off the threads and flatten the weld. Body work as needed.
I don't know if anyone has suggested this before but when you weld thin metal to fill a hole. Put a piece of copper underneath the hole and weld onto that. It takes away the heat and the steel doesn't stick to it. The thicker the bit of copper, the better.
Just a suggestion. For those small holes, I would fill them in with JB Weld Steel Stik (Steel reinforced epoxy putty).. Then, sand it smooth to match the roof line.
More metal music montages please😜😅🤘🏻🤘🏻🤘🏻! Fun to watch you ( and anyone, really) realize your passion. I know jack about cars ( except how to drive one), but you inspire nonetheless! Wishing you continued success, Ms. Sarah!
Roof solution. Drill out the rivets. Hammer the hole into a countersink with a suitable punch (carefully). Put a countersunk rivet in the hole. Sand any high spits and fill any low spots. Maybe use metallic filler or epoxy. Done. It's not welding but it fills the holes soundly
I’m still a sucker for a cabriolet not only due to the climate but that it looks cool. I know Sarah doesn’t approve but I could care less about convention!
I appreciate that I get to live vicariously through Sarah. I have wanted an early Celica for a long time. But they are known for rusting. Things rust easily in my climate. And I don't have a place to park in doors 😞
Hah!! A little trade secret... When Roots/Chrysler decided to squeeze the Ford 260, later the 289 V-8 into to the Sunbeam Alpine transforming it into the infamous Sunbeam Tiger, to gain clearance for the odd firing cyl. head and valve cover it was done with a large mallet!!!
Nice work! I'm glad I'm not the only one who felt like getting the engine solid mounted was a huge accomplishment. Fitting a W12 in an A4 was a major accomplishment in my opinion. Next week I'm going to focus on floor mods on my 72 Audi Super90 Variant that is being AWD VR6 swapped.
@@Grimm-Gaming The W12 is really nice matched with the diesel version of the 0A3 6spd manual transmission. Cruising rpms are really low and 3rd/4th gears are fun stretching out.
I miss my first car (1977 Celica GT coupe) so much. If I had a a couple of spare wishes one would be to have it back brand new like when my parents bought it for my Mom (I got it four years later). Its a lot of fun watching this project come together. Can't wait to see it finished!
i was lazy on my crown vic and filled the landau trim holes with fiberglass filler after i accidentally set the inside of the c-pillar on fire trying to weld. it’s held up fine outside for years, so i imagine whatever much better way you go with shouldn’t fail at all
Sweet ride,. can't wait to get a ride. Ohhhh , and those brown eyes are looking fabulous !
Everyone should be so lucky as to have a Charlie in their life.
Sarah hammered her tunnel to loosen it up so it didn’t chafe. Everything fits nicely now.
Thirsty much?
At some point, nearly every woman has wanted a hole filled.
Under hood temperatures present a terrific challenge in a small engine compartment. Issues such as fuel vaporizing in fuel lines, rails, filters or pumps can manifest. Insulate headers, ensure cool fresh air intake, use extra electric fans etc. Keeping your engine running smooth on a hot summers day in Tucson will depend on temperature management. A cat appeared in one of your vlogs, tell us a cat story! Thanks Sarah :)
Loved the sped up hammering. You could actually see the walls deforming. Great low tech fix!
POR--15 makes a two part epoxy putty that cures incredibly hard and can be sanded and painted over for those small holes on the roof. I used it on a seam of a 68 mustang where I had to weld in a replacement inner fender panel 18 years ago. It was sanded smooth and has never cracked.
Best wishes to Charlie and his wounded back.
Looks like Charlie is doing okay. Love his solutions when your in a pinch
He’s not, his back gets smoked for a few days every time he tries to do anything like this.
@@SarahnTuned I'm sad to hear this. My heart goes out to him.
@@garyworokevich2524 second that. I had a pretty messed up back a few years ago. It's been a long road to recovery.
@sarahntuned How do you donate?
Are you and Charlie together?
Lead for those roof holes might be the best choice. Low heat required and it'll take paint just like the steel. Kind of like those cars back in the 50's and 60's.
This is what i tought also, but it's not only that time era when that is used. Common these days also
The Celica is starting to really come together! Can’t wait to hear it for the first time
Most original Alice in Chains rendition of Angry Chair definitely goes to you. Also, everyone needs a Charlie in their life
I stand corrected, thought for sure you'd have to cut that hood to clear. Well done Sarah.
The AIC reference was awesome
Great Scott you do fantastic work Sarah!
Hope Charlie's feeling well.
If you have anyone there in the Tuscon area that builds the old school "lead sleds" like the chopped and channeled Mercs and such, they probably know an old timer that works in lead filler (what they used before plastic filler). The lead is melted onto the metal so the roof wouldnt get nearly as hot so you could leave the headliner intact.
Massaging the tunnel for a wee bit of clearance rather than cut and weld makes it so much easier. You are killing it girl, so glad you have some help now.
Spot welding those roof holes might warp the roof. What about soft soldering the holes with an electric soldering iron. No fire risk, no warping, metal finish, saves a lot of work and possibly liner damage as well.
There it is!!!! The Sarah - n - Tuned V8 Hammer!!! Boom! This is what the world needs.
I love the fact that you still retain your sense of humour regardless of the level of frustration.
I liked the time lapse while hammering the tunnel. It clearly showed how much space you gained. If the headliner is damaged, it won't be your error. You're great at careful-ing. I agree about welding the roof holes, no choice.
The sound effects for the hammering were da bomb. 🥁
You said "Metal on Metal" so many times, I now have that Anvil song stuck in my head. Keep on rockin
Hi Sarah, a possible repair for the holes on the roof is to use 3M panel bond to fill the holes. Use a small Ball Pein hammer to indent the small area around the hole, and then fill it with panel bond.
Yes, please don't take the headliner out... lol
Steel Wool and soldering iron
My redneck ass would use JB Stick Weld and a file.
@@tombennetts5191 How does that work? What does it do?
Use the 3M b9nd.
So… I was on the road and got my new video notification and couldn’t help myself. I hit the next rest area to watch. Fabulous video of lots of work and success for mounting the new heart. Awesome soundtrack, too. Charlie is always a win. Thank you, Sarah. 👍👍👍
OMG... that Celica smiley face was priceless.
Doing the holes in the roof, I would not open a can of worms by removing the head liner. That material is from 1974 and is likely to tear. Since I don't know what you have for body hammers, use the round end of a small ballpien hammer on the hole and hit it with a a dead blow mallet to dimple it down then use JB Weld to fill it, then body fill over that. Panel bond may not be moisture proof but JB is. I would not use All metal or Alumalead, I've had cracking failure over a few years in the hot sun using those products.
The headliner being pristine should be preserved. Use metal or fiber reinforced body filler On the roof holes. It’s impervious to water infiltration. Of all the areas prone to rusting, the roof is the least likely. Especially in AZ.
Leading the roof is a beautiful minimum heat solution. Old school craft I would love to see you master.
Sure you will get it done right no matter what path you take.
Thanks for sharing
Use lead, or lead free solder to fill roof holes, no welding, just soldering iron. Also you can fill the rear quarter panel wilth solder and grind it. Old body shop technic so its all metal no filler.
37 years in the Air force and I too have never used an acid brush for acid.
I'm having a hard time deciding what's more impressive. All this custom build candy or the fact that Sarah somehow manages to keep her stylin nails intact.
Try a copper strip as a backing plate for the weld between the headliner and roof. Then you would only have to loosen the headliner rather than full on remove it.
Remove the headliner. Sparks will escape and 🔥 will happen. DAMHIK.
There’s jute attached to the steel, not possible without headliner removal.
That sucks.
@@SarahnTuned Have you heard of using lead as body filler? It’s the original body filler and superior. Yes, it will need to get warm to flow, but not welding hot 💁🏼♂️ options are optional 😬
@@orangetruckman - The melting temperature of lead is still hot enough to damage and potentially set fire to the sound deadening material.
Always happy, (in a non sleazy way), to see a new video from Sarah. Not many people can say they have a V8 in their 70's Celica. 😉👍👍😎
I'm totally absorbed in this Celica series of videos.
Another great show, Sarah! Love your quirky sense of humor and the fact that you show your work!
Sarah. Look into the epoxy putty from POR 15 for the holes in the roof. It works great and I’ve never had it fail on many restoration projects. It gets hard enough to tap threads in it.
Yeah I was thinking about that also!
Yep, I've used it before. It worked great.
That's what I would do too. I have bodywork on vehicles with short strand filler filled holes that I did 30 years ago and never had any let loose.
One of the J-B Weld products would also work fine.
@@delukxy Yes, a 2part epoxy is the best way to go.
I love the fact that you do projects on your terms . A Fan from Oz
The music with the hammer was epic! This car will be another baddass Sarah (and crew) Creation!
I'm not even into cars but I'm hooked on this😎👍
It is a joy to watch you two work together.
So happy that you’ve managed to install the engine after so much time and energy!
Thanks!
Proud of you Sarah massaging sheet metal. Your learning new skills.
😎🍺👍🇦🇺
Back in the later part of the 80's, the Victorian police VL turbo interceptors & undercover VL V8's (in Australia) were retired from service which would come through our panel shop before getting sold off into public hands. We would fill in all roof holes from where the light, siren & aerial power cables went through. To save a few dollars, the dealership (Bayford) didn't want the headliner taken out so to prevent the headliner burning up from welding, we made aluminium discs to go under the roof & soldered the disc from the top of the roof. The low heat solder never burned the headliner & the metal roof looked like a file finished lead wipe.
Over a Half Milly subscribers now! Woot Woot!!! Always great to watch! Itll be wildly impressive to see this thing be a drifty monster!!
You could use lead to fill those holes on the roof if you wanted. Since you’re not heating the roof just the lead you might get away with not removing the headliner.
Eastwood now has lead free body solder. Would save the freak outs in comments section when you are sanding it down.
Thank you, Sarah. Now I can't take this song from Disturbed out of my head.
Here we go again withTeam Sarah getting it done. Not settling, not compromising and no slack for our team. Love to see Charlie around as well as Angel. This is great viewing. We can always count on you to give it your all and you do! Press on Sarah!
Mechanic tip:
You dont have to pump the engine crane for making it go up empty . Just lift the boom with your hand and it will stay where you left it
Have you considered fixing the roof using lead solder? The holes are small enough that you could just use a big Weller 100W soldering iron like they use for stained glass. The solder melts at a very low temp, so very little chance of damaging the headliner.
yep
Super work Sarah & Charlie! Another obstacle bites the dust! And another one gone, & another done, another bites the dust... "superb fab," just Fab baby... "just Fab! See y'all soon I am sure! CAUSE: IT'S SARA'S CHANNEL! J
Charlie has such clean welding lines!
Really surprised you don't have to cut the tunnel or firewall to fit new engine etc that's great :)
It fits!! Had to take a hammering, but it’s in there. Nice work. Yay Charlie and his fab skills.
That project is starting to take shape and look sweet. You are smart and lovely plus you got great help, just wish I could be a part of the team.
I cant wait to see this thing running and driving
It's going to be beautiful when it's done. Great work
Quick tip! For your engine hoist and jack too! When lowered to lowest setting and needs to be up a little high before contact or hoist action, loosen the release valve and put your foot on the base of the jack or hoist. Raise the hoist with your shoulder or raise the jack by hand and then tighten the release valve at the height you like! No pumping that dang lever all day!
VERY impressive engine install. PLEASE reconsider taking the headliner out to weld up the holes in the roof. Countersinking the holes and filling them with JB Weld will not only work, but save you a shit ton of time. Rock on, Sarah! 😁
You should check out this months issue of Canadian Hot Rods. There is an article on a 73 toyota celica with an LS swap done to it. Same flares and spoiler as yours.
love watching charlie work
Congrats. That's a huge milestone.
Charlie is a genius with that flimsy fender fix
I am so glad Charlie and AFC are there for this passion project. Y'all work so well together.
Hello from Glasgow. 👍🏴😁
🏁
Ingenious solution from Charlie on the wheel well strengthening. :) I was with you on the not hammering out the clearance, but it worked so well and doesn't look as janky as I thought it would. Great solution from whoever suggested it. :)
For tiny holes use JB Weld and sand it down
So glad you clarified which Bono you were talking about :)
The reduced lighting to emphasize Charlie's engine bay welding was really cool... Your editing and production skills are always getting better! Bravo!
To weld the roof
Method one
Get some counter sunk screws that fill the hole with a little overlap.
Remove the threaded part to just leave the head.
With a screwdriver and hammer dent the roof slightly to ensure that there will be a small depression to fill when done. Tack the screw heads into the hole while pressing them down with a screwdriver.
Use just a few tacks that will survive sanding.
Flatten the weld and fill over with body filler or low temperature solder.
Method two.
Get some screws that head just pushes through the hole when forced.
Insert them through the holes upside down so the thread sticks out.
Tack around the screw head to weld it in.
Grind off the threads and flatten the weld.
Body work as needed.
Attention to detail is the sigh of a master. Great video.
I don't know if anyone has suggested this before but when you weld thin metal to fill a hole. Put a piece of copper underneath the hole and weld onto that. It takes away the heat and the steel doesn't stick to it. The thicker the bit of copper, the better.
Sarah don’t take out the headliner you can use steel putty and it’s sandable light glaze and Wala ready for paint 👍
Just a suggestion. For those small holes, I would fill them in with JB Weld Steel Stik (Steel reinforced epoxy putty).. Then, sand it smooth to match the roof line.
Another great vid! For those roof holes, why not use lead? They look small enough to fill with some lead solder with an electric soldering gun.
The ole BFH is a very handy tool.
Congradulation on getting it in there
More metal music montages please😜😅🤘🏻🤘🏻🤘🏻! Fun to watch you ( and anyone, really) realize your passion. I know jack about cars ( except how to drive one), but you inspire nonetheless! Wishing you continued success, Ms. Sarah!
Whoo!!!! Big V8 in Tiny Car!!!!
Exciting times! All of the fab looks glorious! Tough decision on the roof holes - but you'll definitely make it happen!
Roof solution. Drill out the rivets. Hammer the hole into a countersink with a suitable punch (carefully). Put a countersunk rivet in the hole. Sand any high spits and fill any low spots. Maybe use metallic filler or epoxy. Done. It's not welding but it fills the holes soundly
I’m still a sucker for a cabriolet not only due to the climate but that it looks cool. I know Sarah doesn’t approve but I could care less about convention!
I think this is the best solution, if not the most desirable. Saves quite a lot of work.
I appreciate that I get to live vicariously through Sarah. I have wanted an early Celica for a long time. But they are known for rusting. Things rust easily in my climate. And I don't have a place to park in doors 😞
Hah!! A little trade secret...
When Roots/Chrysler decided to squeeze the Ford 260, later the 289 V-8 into to the Sunbeam Alpine transforming it into the infamous Sunbeam Tiger, to gain clearance for the odd firing cyl. head and valve cover it was done with a large mallet!!!
I love this project, and I love your proper pronunciation of Seleeka and aluminium. :)
you guys are killing it on this build...nice work Sarah n crew!
Sarah the woodpecker😂
The speeded up hammering was funny!
Spirit level on the engine,
"Make the noise" !
Sarah, hows Charlies back doing? Hope he's healing up!
Not good, still trying to find a Dr. that will do surgery.
I will keep Charlie in my prayers. I have back issues too and know how terrible it can be.
How to make our day? Sarah video! whoop whoop!
Hammer time. Way to go. That will be one fast Celica.
This is really cool build. Can't wait to see you give it the beans.
Clearancing the transmission tunnel went easier than you expected because the little Celica _wants_ a V8! 🙂
Nice work! I'm glad I'm not the only one who felt like getting the engine solid mounted was a huge accomplishment. Fitting a W12 in an A4 was a major accomplishment in my opinion. Next week I'm going to focus on floor mods on my 72 Audi Super90 Variant that is being AWD VR6 swapped.
Ok a W12 wagon. Sounds cool.. i wanted to NA subaru awd a 65 mustang coupe oneday. Have it as a restomod daily. Not powerful just awd n sounds cool
@@Grimm-Gaming The W12 is really nice matched with the diesel version of the 0A3 6spd manual transmission. Cruising rpms are really low and 3rd/4th gears are fun stretching out.
I miss my first car (1977 Celica GT coupe) so much. If I had a a couple of spare wishes one would be to have it back brand new like when my parents bought it for my Mom (I got it four years later). Its a lot of fun watching this project come together. Can't wait to see it finished!
Solder iron for the small holes and water sponge to keep it cool.
This car is going to drive so nice. I'm already envious
Music choice was on point in this video.
i was lazy on my crown vic and filled the landau trim holes with fiberglass filler after i accidentally set the inside of the c-pillar on fire trying to weld. it’s held up fine outside for years, so i imagine whatever much better way you go with shouldn’t fail at all
Honestly there are low heat methods you could use like leading that would work on the roof