Brilliant. So calm and information rich video. It can be a best tutorial for UA-camrs who really want to make videos full of knowledge and craftsmanship.
Thanks for the video. Really appreciating you share the info's.. For getting '8-Ohms' total impedance for this Three-way Crossover what should be the speaker's impedences Should be?
In your next way video, may be, you can do a tutorial on how to connect speakers connections, in parallel or series, to tackle it's ohm and match amplifier impedance.
Excellent , when we are talking of power , are you refering to RMS power ? Secondly , I have Bolton 10" woofer 8 ohm 60W Model 25 JW 22, Bolton Midrange 8 ohm 60 W Model 12 PM 2 & Philips Dome tweeter . I am looking for a suitable 3 way cross over to listen to the ONKYO AV Receiver in stereo mode. Can you suggest some model ( The existing networks were from Bolton Model 312BN2, dont want use it as not aware of the specification) Can you kindly tell me number of turns required for 3.2 & 0.18 mH ?
Very well explained kindly suggest some god brands tweeter and woofers ..I used to have philips woofer and dome tweeted but not these are discontinued ..I wi appreciated your reply
sir I've a homemade amplifier in which 7294ic is used(double ic) I've used 12-0-12 3amp transformer for powersupply so what type of crossover should i use..
I'm Sanku Mondal I live at north 24 in habra , I watch all your videos. Sir I would like to know from you what will be the coil if you use two 50 watt woofer in 100 watt mono amplifier .
Crossover network is used for frequency separation. You can use one or two woofers for the same cut off frequency. The network shown can handle upto 100 watt. For more power, the resistor wattage to be increased.
Hi , can u help me on reading Midbass 4ohm, 12db slope 80hz-450hz Midrange 4ohm, 12db slope 500hz-4khz Tweeter 4ohm, 12db slope 5k-20khz Wonder u can help me on all this reading for coils and capacitor... Will be running high pass on my amplifiers. Thx in advance
Please tell us can we add 4 ohm 100w 10" and 8" mid two speaker and 4" tweeter is there any effect on impedance or it will change into 2 ohm our amp support 4 ohm.
Nice Sir, I want to Crossover Frequency of 200 HZ and 2 Khz Because my low frequency driver in efficient for low frequency but not for mid frequency and I want 12 db octave please suggest design and values of component
Crossover network doesn't make any change in total impedance. If you connect three 8 ohms speakers, to low, mid and high, total impedance will be 8 ohms. Impedance will depend on Crossover input
You may search in net. There are many sites like www.diyaudioandvideo.com/Calculator/ApcSpeakerCrossover to find value of components. Resistors are used to get smooth high frequencies from tweeter
Mr. Aloke Mukherjee..... M. D. of MECASONIC...... we are proud of you Sir..... warm regards 👍
Brilliant video... Showing the components, circuit and the board development with such minute details is exemplary. Thanks for sharing the video... 🙏
Brilliant.
So calm and information rich video.
It can be a best tutorial for UA-camrs who really want to make videos full of knowledge and craftsmanship.
Thanks
Thanks sir aapne jis tarha se bataya hay. Na or koi nahi bataya hay........ Good example 😊
Thanks
knowledge shared is knowledge gained,...my father used to teach me in this way,...
always loved a teacher like you,.....!!
Thanks
You Sir are very intelligent 🙏 thank you for sharing your knowledge 🙏
Thanks
Very amazing video .
Sir , thank you so much for sharing your knowledge.
I am from Sri Lanka .
Thanks
GOOD DAY THANK YOU VERY MUCH SIR FOR SHARING YOUR AMAZING KNOWLEDGE TO US.
Thanks
Excellent. Explained clearly . Thank you sir.
Great Video. You are an excellent teacher/ engineer
thanks master 👍👍
Thanks
Thanx for video sir. Good to see videos from India.
Thanks
with the experience of life time, You are a Guru
Thanks
Thanks for the video. Really appreciating you share the info's..
For getting '8-Ohms' total impedance for this Three-way Crossover what should be the speaker's impedences Should be?
Thank you sir it's a good lesson and understanding also
Thank you sir for your practical way construction.
Thanks
Nice explanation sir
Thanks
Mr.Aloke Mukherjee (MEKASONIC-Dhakuria- Calcutta)------------------ warm regards from 'CHOWDHURY'
Thanks brother from Dhule Maharashtra
Very much apreciated video! Great results showed.
Very interesting I appreciate your work
TQ VERY MUCH
FOR SIMPLE AND SIMPLE EXPLAIN
RRALY GREAT SIR
BIG THANKS
Thank you Sir I appreciate your work !!!
Thanks
Neat and clean...👍 And it would be good if you teach us the whole calculations😊
Realy your are great. I great full to you thank you sir🎉❤❤❤❤❤❤
Sir, Ur explaination is so Simple yet Very Informative, very interesting.Excellent Video 👍🏻
Very good jop sir you makit very esy to me thank you sir
Thanks
Super... Super Sir ji... Very useful video.... Good luck... For your channel... 👍
Verry Good chacha
Thanks
Very amazing video sir
Great video
In your next way video, may be, you can do a tutorial on how to connect speakers connections, in parallel or series, to tackle it's ohm and match amplifier impedance.
The best explanation of of 3 way crossover , sir did u forget ohms , how to get in touch with u sir
Email makingloudspeaker@gmail.com
thank you so much sir..
I'm Subscribe you
Thanks
Great sir,for your knowledge
Ton of thanks sir
So nice of you
Sopar ❤️ brother thanks ❤️🇮🇳
Thank you for guiding sir.
Thanks
how many output watts for that kind of network... thanks the reply.. and more power.
Very informative video. I just subcribed
Excellent , when we are talking of power , are you refering to RMS power ? Secondly , I have Bolton 10" woofer 8 ohm 60W Model 25 JW 22, Bolton Midrange 8 ohm 60 W Model 12 PM 2 & Philips Dome tweeter . I am looking for a suitable 3 way cross over to listen to the ONKYO AV Receiver in stereo mode. Can you suggest some model ( The existing networks were from Bolton Model 312BN2, dont want use it as not aware of the specification)
Can you kindly tell me number of turns required for 3.2 & 0.18 mH ?
You may try SYCO 3CO12L network from N.G.Electronics Kolkata. Ph 7439728737
Very well explained kindly suggest some god brands tweeter and woofers ..I used to have philips woofer and dome tweeted but not these are discontinued ..I wi appreciated your reply
Great video Sir
You are a master in your job!!!!
I need to passive 3way crossover to be made, sub woofer + mid bass + hise, pls need to contact you
సూపర్ సర్
sir I've a homemade amplifier in which 7294ic is used(double ic) I've used 12-0-12 3amp transformer for powersupply so what type of crossover should i use..
this was great
Can I use 250v .22mfd N p capastor
Can you create a pair of crossover network and sell? I am looking for one pair.. Will be waiting for your reply
Sir can you teach how to make electric guitar pickup? Please.
Can I use dual woofers for 3 way crossover (W+M+T)???
yes if impedence(ohms) and wattage matches correctly ( see calculations for combination)
How do we contact you to make a cross over. I dont have a jig to wind the coils and hand winding is not as neat.
You have to get ideas from my earlier videos on Crossover network
Good experience and explains
superb sir
I'm Sanku Mondal I live at north 24 in habra , I watch all your videos. Sir I would like to know from you what will be the coil if you use two 50 watt woofer in 100 watt mono amplifier .
Crossover network is used for frequency separation. You can use one or two woofers for the same cut off frequency. The network shown can handle upto 100 watt. For more power, the resistor wattage to be increased.
Can this be used for amplifiers with 225w + 225w output?
Dear friend for 180w 20 swg And for 500 w 16 swg. Sorry for my limited knowledge.
Sir can use polar capacitor instead of 2.2 capacitor
What happens if I use it in a lower wattage amplifier say 60 Watts RMS per channel.will this work.
Of course
Thank you sir...from where we can buy your crossover?I need 3-way 12db with four coils.
Please contact me at whatsapp no 9007400622
Superb
Sir how to match ohms and watts of the three way speaker system to the amp .plz replay
hello, is it for 150watts for each speaker or 150w divided by 3 speakers?
offcource 150 to be divided in 3
Why crossovers on AliExpress have extra capictors and resistance aswell coin please explain? is they sound better than this?
Center channel diy 6". Dual k lie crossover bna dein 6 ohm k lie.
Hummmmm. Good.
Sir can we use it for 8 ohms ?
sir, can i use it in 400 or 300 watt amplifier? if yes, then what watt woofer speaker and hf can i use?
Hi , can u help me on reading
Midbass 4ohm, 12db slope 80hz-450hz
Midrange 4ohm, 12db slope 500hz-4khz
Tweeter 4ohm, 12db slope 5k-20khz
Wonder u can help me on all this reading for coils and capacitor... Will be running high pass on my amplifiers. Thx in advance
You can try to get the values from the online calculator in the link below:
goodcalculators.com/crossover-calculator/
Please tell us can we add 4 ohm 100w 10" and 8" mid two speaker and 4" tweeter is there any effect on impedance or it will change into 2 ohm our amp support 4 ohm.
If your mid speakers are 8 ohms, then you can join in parallel to get 4 ohms. If those are 4 ohms then connect a 2 ohms 20 watt resistor in series.
i fell asleep a few times but other than that it was ab great video!
Sir how many turns to have 200 watts of coil?
8ohm 12"in subwoofer crossover calculation please video sir
Sir 12db 3way cross-over please make a video.
Ok thanxs
Where to buy these components in india
10 ohm resistor us kar sakta hu kya sar
Kitna watt ka speaker laga saktaa hu ismain??
gr8 Sir
thanks sir
Thanks
@@makingloudspeaker can you build a pair of 3way passive network kit for me?
Nice Sir,
I want to Crossover Frequency of 200 HZ and 2 Khz Because my low frequency driver in efficient for low frequency but not for mid frequency and I want 12 db octave please suggest design and values of component
You may watch my video on calculating component values for crossover network
Sir 12 inch ke do speaker and ek hise me konsa network use kree??
High power crossover networks are available in the market
Hello dada apniki pa system e 500wats speaker r sange 100wats hf (model number paudio 750/760) lage or network banate parben
video banan
Sir aap 2 woofer 150 watt aur 1 tweeter croossower banaiye
Very we explained
sir 18 inch bass speaker k liya components batadi ji ya sir
Please see my earlier video on Subwoofer crossover
ua-cam.com/video/06Dtra6MCwI/v-deo.html
Sir I need 4 way cross net work design for home audio system 100+100w Stereo Amplifiers....thankyou.... SAKTHI AUDIO- chennai
Good morning sir
Can you sale the 3 way crossover one pair ,if so please send the details
Email makingloudspeaker@gmail.com
Tell us the cut o frequency in this crossover
Sir can u give the dimensions of a 12 Inc's 2 way speaker enclosure thanks...
Which multimeter are you using for measuring inductance of coils ?
It is called LCR meter. You can measure Inductance, capacitance and resistance by this.
Cross meter model
Hi sir super I want this 3 way crossover
Whatsapp to 9007400622
Sir can i connect 4 ohm 20w tweeter & 30w 8 ohm woofer to this network
Yes you can
How can I get this product
What will be total impedance of the speaker after connecting with 3 way crossover ?
Crossover network doesn't make any change in total impedance. If you connect three 8 ohms speakers, to low, mid and high, total impedance will be 8 ohms. Impedance will depend on Crossover input
@@makingloudspeaker thank you sir
Sir from where can buy that capacitor?
I want to buy 2 pices of 2 way crossover , please you make for me
Mujhe 3way cross over lena he kya price he sir
Sir Video Hindi me banaiye Q ke Hindi viewers jada hai ....so think about my little suggestion
নমস্কার স্যার । একটি প্রশ্ন আছে , 3 way ক্রসওভার এ তিনটে 4Ohm এর স্পিকার লাগলে কি স্পিকারের Ohm এর কোনো পরিবর্তন হবে ? উত্তর পেলে উপকৃত হব ।
Sorry, your question is not clear.
You can connect woofer, midrange and tweeter of 4 ohms each.
Cool
How do you determine capacitors and inductor for a given speaker driver selection? And why do we need the resistor?
You may search in net. There are many sites like www.diyaudioandvideo.com/Calculator/ApcSpeakerCrossover
to find value of components.
Resistors are used to get smooth high frequencies from tweeter
@@makingloudspeaker i have used many calculators with mixed results. Can you make a video on how you do this?