Hola Maquinista, he leido en algun comentario que entiendes perfectamente el español. Millones de gracias por tus videos y en especial a esta magnifica demostracion del cambio de cuchilla. Me gustaria saber si es posible que subieras algun video con ejemplos de programacion con medidas de caga, expulsor programable, Eltrotac, bucle, Autotrim... aunque con una programacion sencilla y rápida tambien sería suficiente... Quizas ya lo tienes publicado y no lo he encontrado, o quizas te es imposible hacerlo. En cualquiera de los casos, millones de gracias. Es estupuendo tu trabajo
¡OK amigo! Cuando sea posible, haré un vídeo sobre programación, pero necesito tiempo libre del trabajo y planificación para hacer algo que pueda llegar a múltiples audiencias....No me arriesgaría a hablar portuñol😅😅
0:41 & 1:00 The operator's manual does not say to tighten the fixing screws (a), but tighten the fixing screw (y) again. 12:25 Tighten all the knife screws from centre towards both ends alternately.
@@marconiparello And one more thing: When changing the cutting stick, do it in advance, without a knife on the table, at least not on two screws (d). Good guide! Good luck!
Hello The Machinist Las hojas de papel que pones al final previo al apriete de los tornillos tienen una medida de espesor especifica? o cual es su función ?? Gracias por la respuesta
@@DanielEsqueda-AlliedPrint ¡Hola! Hojas de papel cartón que no sean demasiado gruesas. Yo prefiero cartón de 200/250 g. Las tiras de plástico se llaman "sticks"(english). Utilice un martillo de plástico o goma para evitar dañar la máquina.
Y más!....la función de las tiras de papel es comprobar el corte en toda su longitud. En caso negativo, aflojar retencion de perno excéntrico(y) - girar la excéntrica de ajuste(c) - apretar la retención(y) Ok 👍🏻
We are a factory specialized in machine blades for decades. Our products contain all-steel and inlay-steel, which are widely used in paper, plastic, rubber,leather,wood, textile and metal and etc industry, in cutting,crushing.chipping,coating and etc progresses.
Hello from Spain. Could you please upload a video where a program is created step by step with eltrotak and program loop? Thank you very much for your videos.
@@marconiparello polar 115 xt con autotrim, el modelo es más avanzado, pero la interfaz y la programación es la misma. Voy a hacer un examen sobre esa máquina y tus videos me ayudan mucho, sobre todo el cambio de cuchilla. Muchísimas gracias por responder. Un saludo.
@@arianniortiz8118 AUTOTRIM 😱....¡Qué buena máquina! Eltrotact, es un programa sencillo con pocos datos de información y más fácil de realizar para cortes repetitivos. ¡Atención! No es posible utilizar doble corte en este programa, Aconsejo usar el "BLOCK PROGRAMMING"
Hi, I use a torque wrench. "The knife bolts set to 70 N.m". This is what technicians recommend. Tighten all the knife screws one by one from left to right or all the screws form the centre towards both ends alternately.
@andrewkeller4752. You may already know this. Tungsten Carbide Tipped (TCT) knives have only a single line of fixing bolt holes. This is because the TC “tip” or grinding reserve is 25mm. and only maybe 17mm. can be sharpened/re-ground. And some brands may require a different cutting stick to those for standard HSS (High Speed Steel) or SS (Swedish Steel) knives. If you use TCT knives on any paper cutters, always seek the best technical advice from your local manufacturer’s agency or grinding station. Stay safe and well.
I remember changing a 2800mm (110 inch) knife. It took two people just to lift it into position without nicking the knife. And God help the operator who forgot to raise the knife before installing the new one and crashing it into the cutting board.
The crank eccentric (arm) when turned clockwise deepens the knife for fine adjustment. Don't forget to tighten the bolt that serves to lock and open the adjustment.
The best answer I've found. I think you have a problem with the SK card. The card SK controls the cutting cycle. The best point to begin with is, move the card to another machine or bring a good card to this machine and check it out. The donor machine don't necessarily have to be E. it can be S, ES, E or ED. But before you plug in, check the card model, it should be same or the newer version than the replacing card.
You need to know what you are doing to avoid accidents... And if the machine is big 155 or 176, it becomes more dangerous because the knife is too big and heavy.
@@marconiparello yes I know,I changed them many times.I used a holder that you screw in to use as handles. I programmed many cutting jobs. i did rule ups and input all the cutting positions and saved the programs for future use. I had extended air table for big jobs. I worked for ABC of Switzerland,Thompson Litho,and Jeda Publications in my time. I also operated Stahl folders,Didde gather all collator,and Japanese saddle stitchers. I cut paper for Komori waterless press. I made special jigs to trim books and operator manuals, for Intel, HP corporation.
@@DarbyOgill-pf8mm Nice! It's an honor to have you watching my videos. I work in small companies, I would be very happy if I had the opportunity to work in important companies like the one you mentioned. Thanks for the comment. 👍🏻
Hola Maquinista, he leido en algun comentario que entiendes perfectamente el español. Millones de gracias por tus videos y en especial a esta magnifica demostracion del cambio de cuchilla.
Me gustaria saber si es posible que subieras algun video con ejemplos de programacion con medidas de caga, expulsor programable, Eltrotac, bucle, Autotrim... aunque con una programacion sencilla y rápida tambien sería suficiente... Quizas ya lo tienes publicado y no lo he encontrado, o quizas te es imposible hacerlo. En cualquiera de los casos, millones de gracias. Es estupuendo tu trabajo
¡OK amigo! Cuando sea posible, haré un vídeo sobre programación, pero necesito tiempo libre del trabajo y planificación para hacer algo que pueda llegar a múltiples audiencias....No me arriesgaría a hablar portuñol😅😅
0:41 & 1:00 The operator's manual does not say to tighten the fixing screws (a), but tighten the fixing screw (y) again. 12:25 Tighten all the knife screws from centre towards both ends alternately.
OK! I do a light tightening but it is not necessary on the screws(a).
Thank you for watching my video 👍🏻
@@marconiparello And one more thing: When changing the cutting stick, do it in advance, without a knife on the table, at least not on two screws (d). Good guide! Good luck!
@@borisvik9989 I understand and agree with your post, it showed that you have knowledge.
I believe this sequence is the most dangerous!
ua-cam.com/video/qfbmF5hMtrU/v-deo.html
@@marconiparello Uh-huh, just changing the cutting stick is done right🤔
Hello The Machinist
Las hojas de papel que pones al final previo al apriete de los tornillos tienen una medida de espesor especifica? o cual es su función ??
Gracias por la respuesta
And how the strip that you change at minute 9:00 its named?
@@DanielEsqueda-AlliedPrint Siéntete libre de preguntar.
@@DanielEsqueda-AlliedPrint ¡Hola! Hojas de papel cartón que no sean demasiado gruesas. Yo prefiero cartón de 200/250 g.
Las tiras de plástico se llaman "sticks"(english). Utilice un martillo de plástico o goma para evitar dañar la máquina.
Y más!....la función de las tiras de papel es comprobar el corte en toda su longitud. En caso negativo, aflojar retencion de perno excéntrico(y) - girar la excéntrica de ajuste(c) - apretar la retención(y) Ok 👍🏻
@@marconiparello Muchas Gracias por responder,
¿Es necesario el cambio de stick para el ajuste de la maquina?
Saludos
Thank you so much ❤
😎 I hope it was useful for you.
We are a factory specialized in machine blades for decades.
Our products contain all-steel and inlay-steel, which are widely used in paper, plastic, rubber,leather,wood, textile and metal and etc industry, in cutting,crushing.chipping,coating and etc progresses.
Your visit is of great relevance to my channel. Thanks 👍🏻
Hello from Spain.
Could you please upload a video where a program is created step by step with eltrotak and program loop? Thank you very much for your videos.
Hola Arianni! Soy brasileño y estoy pensando en cómo hacer un video para una audiencia diversa. ¿Cuál es el modelo de su máquina por casualidad?
@@marconiparello polar 115 xt con autotrim, el modelo es más avanzado, pero la interfaz y la programación es la misma. Voy a hacer un examen sobre esa máquina y tus videos me ayudan mucho, sobre todo el cambio de cuchilla. Muchísimas gracias por responder. Un saludo.
@@arianniortiz8118 AUTOTRIM 😱....¡Qué buena máquina! Eltrotact, es un programa sencillo con pocos datos de información y más fácil de realizar para cortes repetitivos. ¡Atención! No es posible utilizar doble corte en este programa, Aconsejo usar el "BLOCK PROGRAMMING"
Do you have tools for safety pressure ?
Hi, I use a torque wrench. "The knife bolts set to 70 N.m". This is what technicians recommend. Tighten all the knife screws one by one from left to right or all the screws form the centre towards both ends alternately.
What is considered the inferior line and superior line of fastening drillings?
Are the knife holes. Usually 3 rows in sizes 115-176
If the knife is too worn, use the upper holes.
Thank you for watching my video!
Thank you! Great video by the way.
@andrewkeller4752. You may already know this. Tungsten Carbide Tipped (TCT) knives have only a single line of fixing bolt holes. This is because the TC “tip” or grinding reserve is 25mm. and only maybe 17mm. can be sharpened/re-ground. And some brands may require a different cutting stick to those for standard HSS (High Speed Steel) or SS (Swedish Steel) knives. If you use TCT knives on any paper cutters, always seek the best technical advice from your local manufacturer’s agency or grinding station. Stay safe and well.
I remember changing a 2800mm (110 inch) knife. It took two people just to lift it into position without nicking the knife. And God help the operator who forgot to raise the knife before installing the new one and crashing it into the cutting board.
Changing knives is the most dangerous part of our job, and if it's a giant knife, it's even worse. Thanks for the comment.
I get confused when resetting eccentric bolts from right to left any advice?
The crank eccentric (arm) when turned clockwise deepens the knife for fine adjustment. Don't forget to tighten the bolt that serves to lock and open the adjustment.
The two eccentrics under the knife prevent the knife from sliding vertically after adjustment.
Hello sir my machine have problem.
Maximum cutting Time elapsed (469) ?
The best answer I've found.
I think you have a problem with the SK card. The card SK controls the cutting cycle. The best point to begin with is, move the card to another machine or bring a good card to this machine and check it out. The donor machine don't necessarily have to be E. it can be S, ES, E or ED. But before you plug in, check the card model, it should be same or the newer version than the replacing card.
You should check the 2 activation buttons first to see if there is a problem.
But, I don't believe it's the buttons because the message would be different.
Gracias Dtb siempre
ขอบคุณมาก
Very nice so beautiful
@@sonubhai8413 Thanks 👍🏻
👍
👏🏻👏🏻👏🏻👍🏻👍🏻
No comments
Dou sel hawu mach?
Not for sale bro. 👌🏻
changing the knife is scarey.
You need to know what you are doing to avoid accidents... And if the machine is big 155 or 176, it becomes more dangerous because the knife is too big and heavy.
@@marconiparello yes I know,I changed them many times.I used a holder that you screw in to use as handles.
I programmed many cutting jobs. i did rule ups and input all the cutting positions and saved the programs for future use. I had extended air table for big jobs. I worked for ABC of Switzerland,Thompson Litho,and Jeda Publications in my time. I also operated Stahl folders,Didde gather all collator,and Japanese saddle stitchers.
I cut paper for Komori waterless press. I made special jigs to trim books and operator manuals, for Intel, HP corporation.
@@DarbyOgill-pf8mm Nice! It's an honor to have you watching my videos. I work in small companies, I would be very happy if I had the opportunity to work in important companies like the one you mentioned.
Thanks for the comment. 👍🏻
👍