Really great. No image Transmission Signal bothered me for some time since I bought the drone. Today I followed your instruction step by step, I got signal finally. Thank you so much!
Man, you are a life saver!! I updated the firmware on my drone (P4/PRO) and I lost my video signal and I had no GPS. I could still fly it but very limited distances. When I tried to update my controller with the memory card it wouldn't work. I forgot to unzip the file before putting it on the card. I should have known this. Once I unzipped it the updater on the controller found it and did the update. Now my drone works perfect. Thanks so much!!!
For a company as advanced as DJI I can't help but wonder why they don't design these routines to be EASY to do rather than the bloody minefield it seems to be. I mean the sort of thing where a big red button comes onscreen and tells you exactly what connections to make and after that maybe a big blue button when you hit it, the whole shemozzlemaflip just goes ahead and does its clever stuff. Not everybody knows about zipping files for instance... Being even mid-range computer-savvy shouldn't be a prerequisite to routine maintenance like this. Oddly enough Ken's video was the one I watched immediately before this one. Maybe now when it happens to me I'll not be so inclined to panic?
I can only say...I AM VERY DISAPPOINTED WITH DJI. Good products but awful customer support, repair and software. After sinking over $2,000.00 on P4P, Goggles, extras......I have a shaking, wobbling POS flying, I have done everything...re calibrated IMU, Compass, wasted hours searching and nothing. Then, I purchased the HDMI module so I could plug the DJI goggles using HDMI port.....to find out that is only works with the USB port...so I need disconnect my Ipad. First they told me to send the HDMI module, one month later they tell me there is nothing wrong with the module, then they tell to send the RC....another month goes by and they return it telling me that the RC has no problem. I don't think the problem is the goggles or the cables because I tried a monitor with the HDMI port and had the same issue....no image, just the OSD display and turns on and off between black screen. THIS WAS THE LAST TIME DJI GOT MY MONEY, thank God I did not go for the Inspire 2....would be a double loss
For the DJI 4 (ONLY not any other) video telemetry issued I copied this from another forum and it worked to fix it perfectly. Had to try several steps several times but be patient. It works! 1) Install DJI GO 3 app from Apps store, launch app (at this time P4 is off until I say) 2) Select P3 Pro as aircraft (SE and Standard are wifi, not sure if this would make a difference), using the 3 dashes at the top right of the app press and hold for 10s or so. A new screen appears showing suggested current firmware of RC. Scroll down to firmware 1.6.0 select "Firmware Refresh". Wait for it to install then close the app and shut off RC. 3) Reboot RC, after a few minutes on shut off RC (not sure if this is really required, but it seemed right) 4) Open up DJI GO 3, Select P3 Pro and press camera (have the lightning cable connected to RC and iPad/iPhone). I had over 50% charge on my RC (btw) 5) Once in main screen with telemetry info wait a few minutes and press the Left upper area just next to the DJI logo saying "No xxxxxx connected " in red, this will take you to the Aircraft setup screen. 6) There you will see a warning message triangle, press this area and it suggests upgrading the firmware as you have 1.6.0 installed and the latest is 1.9.3 7) This started the firmware download and then with lots of beeps and blue flashing light the upgrade was a success !!!!! 8) On completion it will tell you to reboot the RC. At the same time I closed off the DJ GO 3 app. 9) Reboot the RC again. Mine complained at low battery so I did a second reboot and 3 white LED battery level lights came up as well as the RED LED indicating no aircraft bound. 10) Turned on P4 and launched DJI GO 4 app and BANG.... full signals on RC and Video feeds and NO flashing red/green led any more just solid green. So fingers crossed for her maiden flight tomorrow ( double fingers crossed) I hope this helps others; note the DJI GO 4 apps does the same if you hold the 3 dashed lines for 10s or more. I did not try this route to roll back the firmware on the RC.
I'm glad you got it all figured out. When I did my update a couple of weeks ago, I just used the phone app and did the drone and then it told me that basically the controller needed updated so then I had to do that as well and all was good. Keep in mine mine is not the plus version that yours is so obviously something is played differently.
Sir than you so much. I am using a drone from my school grant and I had a "no signal" issue. The camera feed would not show up on the monitor but the camera still functioned. I thought I broke something and for the camera not being mine only made matters worse. Turns out it was just a simple firmware error!!! Thank you so much!!!!
Thank you! The confirmation on how the cables are supposed to attach was a major help. Phantom 4 Pro+ vs Phantom 4 Pro V2.0 - I downloaded the firmware for the V2.0 by mistake (duh). That file wouldn't extract to a .bin, but instead just a directory, and the pdf instructions say to just put the .zip on the sd card by itself. I was really frustrated until that facepalm moment when I realized it was the wrong firmware. The firmware for the Phantom 4/4+ does extract to a .bin and it worked immediately. No test flight yet, but I'm hoping this resolves a ton of issues I was having.
Have you noticed any new issues with the screen? I can’t get my fly safe list to enable to fly in a certain area. Why is this happening? I’ve heard that there’s no update for version one anthem for Pro plus
Followed your instructions: format card, download latest firmware via website onto sd card, put the sd card in the remote, then started the process. All looked good, but at the end of the auto-reboot, i get an error "Update Failed: Error code:800". Any suggestions? Thanks!
You know if is there a difference between the pro and 4 ? Im having the same problem with the pixels, and can’t find a solution for it, or how to do it
Good stuff! I replaced my P4PRO gimbal and now I have no video. I;ve tried to update everything I can think of still no video. No errors shown "normal" status but no video. Black screen on mini Ipad. Thanks for any help
just FYI - you mean phantom 4 PRO but in your video description you wrote only 4 - which is a big difference. I have a 4 so your video isnt helping me at any issue i have with my drone right now.
decided to take my phantom 4 out for a flight yesterday after a few months of closet time, did the updates and it flew like crap! pixels all over the screen, and non responsive at times! luckily i got it back safely but this is ridiculous! it flew completely fine before these so called "updates". can't they just leave good enough alone. if it ain't broke don't fix it.
Hey Last week I did the same thing. Went to fly my Hanson 4 Pro for the first time in a week or two and I got the message inconsistent firm ware do I swiped it and updated the drone.. now I have really bad not very usable video stream on my controller. I tried a lot of things but I haven’t tried to update the controller firmware yet. I will try that next. My Mac has the latest OS on it and they do not have a DJI assistant version that will run on a new Mac that also has Phantoms drone. DJI failed to support Phantoms on the new version of assistant 2. I can go by a PC I suppose. This is the first drone night mare firmware problem I’ve had in years
JP Matatan did you ever find a fix? I have a P4 also with same problem, no micro SD card slot on the controller. I'm way beyond pissed at DJI true lack of accurate programming and lack of real support. You see all these videos and people say and Bam it works... Not here.
My P4P+ recently had a firmware upgrade to the AC and RC, but now the touch screen camera controls intermittently freeze, so hugely annoying . Any ideas as to how I might resolve this would be much appreciated ?
Many thanks for making this video. After getting off the phone with DJI tech support today, I am shocked that they still havent addressed this problem. My question: When you downloaded the .Zip from DJI, where did the .Bin file show up? When I open the .ZIP and look at those contents, there is no .BIN anywhere to be found. The struggle is real over here........
I'm a new user of phantom 4 pro, only 1 month and i had a problem with image in my smarthphone like you shows. After firmware update the images on my smarthphone are completly black. my English knowledge is a little poor. could you write please an essenzial list of steps to improve the image quality of connection between smarthphone and phantom 4 pro? only essenzial steps please . Best regards, Giuseppe
Quick question.. do you know if the latest firmware for the P4P+ fixed the issue where users cant hide the OSD from the HDMI output feed? this is specially used when been used to TV broadcasting, so the output video is clean with no UI stuff. There are so many complaints in the forums, but this happened last year, and I cant find anywhere if this issue got fixed or not. Im planning to buy the Drone only if this feature is available :(
just a heads to save people tons of time who are having problems with distance-video issues. if using a android tablet or phone the type of cord (charging cord) does make a difference. i had problems and switched from gas station bought cord to the original verizon cord and worked flawlessly.
Hey I was hoping you could give me some insight for an issue I’m having with my camera/screen. I have flown my new P4A 5 times. No issues. But I notice that the “real time” play back will slightly lag or glitch and I thought it was only going to be on my phone, but I saw this issue when I was editing on FCPX also. What happened during editing is a black screen slides across my footage from top to bottom really fast and ruins my shot. Have you experienced this or heard of this?
I tried everything but it is not working the controler wont see that there is a file. i tried 2 different sd cards and formated them in the drone in the controler and on the pc but it just wont see that there is a file with an update.
I had that problem with my tablet. The solution was to use a more powerful device. Video feed is low priority and if your mobile device can't supply the CPU power, you won't get video or choppy video like that. I switched from a 8 year old tablet to a 2 year old Samsung Note 5 and all was good after that.
So, I had a failed update with my Phantom 4 Drone standard. Everything is working fine, but the camera is not sending an image to the screen. I've tried resetting the camera, adjusting the settings, reformatting, etc. Nothing... Will DJI Assist help me fix the bird?
@@readysetdrone Awesome! I appreciate the reply. I haven't had time to reset the remote yet, but I'm going to try today. the strange thing, is that the indication light next to the sd card slot on the drone is cycling green, orange, red. Like I said, it seems to connect to the remote, but the remote is not able to see what version of firmware is on the drone. whenever I go into the software through the remote, and hit "Check firmware" for the drone, it just keeps thinking, and never sends back a result. The app doesn't freeze, and the drone is still communicating with the remote, but it stays in that green orange red blinking phase. The other symptom I'm having, is when I connect my phone directly to the drone, it doesn't communication with the app. Thanks for your clear concise video! It's much appreciate.
Hello, I'm trying to download an update but I keep getting the error saying " insufficient storage 2G " I have a memory card in the RC. The. Current version I have now is V01.02.02.00 can you help me with the problem I'm having? Thanks...
One question - are you on wifi and is the wifi connection good? Also, do you have the drone and control connected via USB? It can't be the larger USB connection, needs to have that OTG cable with the smaller micro USB on both sides.
Updated firmware yesterday . After rebooting and taking up about 50 feet I get downward infrared warning amd to land . Wasn’t having problem the day before. Any ideas of what may be causing this
Could there be something blocking your IR sensor? Are you flying over grass? My suggestion would be to reboot everything, take it out to a grass field away from concrete/buildings/etc and give it a try there. Also, be sure to do a compass calibration. Hope that helps!
Hi there! I've got a Phantom 4 but my controller doesn't have a micro sd card.... it has usb and micro usb only... In this case what do you recommend? cheers!
Instead of connecting to your PC and downloading, couldn't you do an OTA update?, as you seemed to have the option on the controller to update through WLAN. Would save all the connecting and disconnecting cables if you could :-) Seems DJI have made this unnecessarily complicated. While not in the same class as the P4 range, my Xiaomi Mi drone 4k does all firmware updates with just 1 click. That is 5-6 different firmware's for Quad, RC, gimbal, camera, battery etc. It's certainly not without it's own issues though! I guess in the end, the more technology they have built in to these drones, the more potential issues and quirks! Cheers
As a newby I'm so bummed tha DJI has made this so complicated and no instructions on what to do. Thanks for sharing this. I have no signal after updated and my controller just beeps. So frustrating
Did you update the controller and the drone? It should be easier to do if you have a regular P4 or P4Pro...I think part of the complication is with the P4Pro+
Nope P4 has exact same issues but we don't have an mcsd slot to download any firmware and local install. We are at the mercy of the app that buy the way will not download the new firmware, only the old to downgrade but once you've attempted to upgrade the remote will not accurately see the firmware on the P4 and says you have an outdated firmware on your P4 even though you've updated it through the assistant app on a PC.
Thank you so much, I was getting very frustrated trying to update the controller through wifi. I haven't flown it since the update.. but I no longer have a grey monitor and everything seems to work well again! Much appreciated
This was a great walk through Kell. I’m planning on purchasing the phantom 4 pro 2.0 soon, haven’t decided if I’m going to do the one with the screen or not on the controller. I’m just so used to using my iPad Pro 12.9 now. But if I do get the one with the screen, this was a great vid to let people know if they have the same issue you had. 👍🏾👍🏾👍🏾
Wow, I got the spark, my first real drone and if I like the flying aspect with the photography, I would get a phantom 4 pro as it as the 20MP camera. Maybe might get the Mavic as it transports easier. But you're video really does highlight the complexity of ensuring everything, the software is updated and understanding the all the little nuances with the software combined with the hardware. Anyway, I really enjoy your video's. They are very informative and one of the reasons, why I got the Spark.......sorry not from RSD but straight from DJI..... the red one.... Thank you for a nice video.
Thank you for posting the fix. When I have upgraded the firmware on the Mavic, the DJI Tutorial shows you how to update the firmware on both the Mavic and controller at the same time. Is this not available on the Phantom 4 Pro ?
I think it was more complicated because I have the "plus" version with it's own screen, which means that updating the controller is a bit more of a challenge.
You know that's what I was thinking. So glad you got it figured out. I am saving my nickels and dimes to get a Phantom 4 or maybe wait to see it's replacement.
Thanks for your quick response. I have tried rolling back the firmware, but DJI Assistant 2 cannot do it. DJI have locked us out of that here in Australia. Maybe everywhere. I think I will have to wait for someone to discover a hack to bypass the DJI upgrades that seem to be nothing but buggy. Having said that, you seem to have a good upgrade that is working fine. I hope you do not get the same problems we get here. I sincerely hope you do not get any issues with flight stability, "phantom no-fly zones" etc, that we are experiencing. My farm is 2 km away from the Civil Aircraft Safety Authority (CASA) indicated NFZ (a small rarely used airport), yet DJI are saying the NFZ encompasses an area about 7 km radius from the airport. Australian law is 5.5 km radius for an airport. DJI have dropped the ball here. Love your channel mate. Thanks for a professional, friendly and informative method of getting us novices up to speed. Have a safe and happy day mate.
I am using phanthom 4pro v2 and iPad meni4 I had recorded vedios in internal memory with 4k quality but here there is problem that is when I back up all these recorded vedios I am getting all these vedios with 720pxl I want all these vedios with same quality what ever I done ft so how to back up all these with 4k quality
Can tou help me out...i try to do the factory reset on my 4 pro plus after reset is asking me to login but i cant not connect to the wifi. How do i connect to wifi thanks
You should be able to connect to wifi through the app using the touch screen. If that doesn't work, I'd using DJI Assistant (free software) on your computer. If you still can't sort it out, contact DJI tech support. Good luck!
Does the update changed anything in the screen? I was interested to buy the pro plus but seems that has too much issues to update and cannot inatall third party apps
Honestly, if I could do it again, I would not buy the Plus - it has more issues than a regular phone and is more difficult to update. I would go with the plain old DJI P4Pro and skip the plus.
Having stability problem after crash, no damaged to drone actually except propellers, someone saying that its an motor problem and motors need to be replaced, is it true reason behind that?
Thank you so much for this video, you saved me sending back to DJI only for them to tell me it was a software issue. Why does my controller not automatically update or install updates over wifi? I don't know, but at least now I do for the future. Many thanks
Thank you for this, I just got a new P4P+ and thought I had completed all the updates, registrations (DJI & FAA) for prep prior to the first flight, I got down to a site for my first flight and was getting the same pixelated screen. I too tried to change the frequency. Did not help, So I hope this does the trick. I will be installing the bin file in the am. The other problem I have are pop ups that say fly with caution, magnetic interference. I had calibrated the IMU on a level surface then the compass and still get the interference pop ups. Maybe this will fix the issue also. I know the area I am flying is ok as my Mavic Pro has no issues when flying at the same location. Thanks for all the great information.
I own a Phantom 4pro+ too... So after the August 2017 firmware update my video image was completely pixelated... After searching the forums I learned that by doing a factory reset on the controller the video issue would get fixed. I did that and the issue with the video disappeared. Thing is that now the telemetry isn't accurate, the indicator LEDs on the drone blink 4 times green as it should be, and two long red blink ones... The interesting part is that the application aircraft's status tab shows all systems working normally🤔 . I called DJI customer support and they told me to perform an IMU and Compass calibration to fix the issue. I did it, but the problem still happening. The aircraft also shows a negative number on its altitude gauge with the aircraft still on the ground. I'm stuck with a $1700 paper desk weight in my house because under this conditions my drone is not reliable for flying. Ohh, another thing is that the gimbal moves by itself side to side really slow without any inputs...🤔 Anybody experiencing something like that? I need help desperately..
Wow...that sounds terrible. I have a couple of thoughts. First, I know that the P4 (and all other DJI drones) are very susceptible to magnetic interference. Be sure you are not on concrete with rebar, near power lines, etc. I have seen the negative number on the altitude before when I start it in one place (like on a hill) and then move to some place lower...but never on start up. The camera thing is weird. My only suggestion would be to do the reset again, update to the latest firmware, then go calibrate everything out in a big field - away from any possible interference. Maybe hover it 5 feet in the air for a bit to see if it is stable. I wish I had a better answer...please let us know if you manage to get it fixed.
"Ready Set Drone" I don't have an updates option in system settings!!! Any thoughts? Thanks for the instructional video, this is the closest i've found to solving the problem.
I am really having issue controlling the phantom 4 Pro. Recently bought, like a month ago. From last 2 days it’s really giving me hard time. Just right after starting and about 3 feet it doesn’t even stay at one place.. it’s keep moving... even when wind is 2-3 m/h. I had a chat with customer service and they said do the firmware update, IMU and calibration. I did all that but nothing is changing.
Yesterday, while I was updating firmware, and calibrating compass and IMU, after everything was done, rebooted both the bird and the RC, then suddenly, the bird was not connected with the RC anymore. The battery status was showing as Unknown, GPS was not communicating, the camera screen was showing the bird as not connected, etc. I was frantically trying to figure out, what could have possibly gone wrong. Tested everything, no result. It kept saying that wi-fi was turned off, and needed to be re started. Suddenly, I realized that I had left my cell phone out in the car. So, I went out and brought the cell phone back. It was dead, so had to put it on charger. As soon as it got some life back, I turned it on. everything was back to normal. The bird was back on line, and communicating with RC, the GPS satellites were back on, camera was responding. Even the Flight simulator was responding. I don't know if all this had anything to do with the fact that I am using my cell phone's wi-fi network, and since the phone was not around, and was dead, it dropped all signals, and the bird started playing dead. But then again, just to test this thought, I turned off the phone completely, but the things were all working normally. So, I thought, I'd just toss this in and let all you experienced guys tell me I was wrong.
I HAVE A MAVIC PRO FOR 5 MONTHS AND NEVER DID A FIRMWARE UPDATE AND IT FLIES PERFECT. MY UPDATE WAS TO CHANGE THE MUSIC AND HELP ENHANCE THE GOGGLES, BUT TO FLIES PERFECT, DOES EVERYTHING, I MEAN EVERYTHING ITS DESIGNED TO DO. IM AFFRAID IF I DID A FIRMWARE UPDATE I WOULD HAVE TO TAKE A PICTURE OF IT AS IT WOULD BE THE LAST I WOULD SEE IT
Hallo, Reiner here from Germany. Have near the same Problems then you with the Controller.....but how/ wich Format you have to Format the micro sd card?. My English is not so good, and i try to understand, but it was a little bit to fast. Thank for help, and sorry about my English
I saved up for over a year and sold stuff to get my first phantom 4 drone I was so excited. I started it up it went up to about 50 feet and it shot off like a rocket and never seen again I was so pissed and shocked excited one moment and cry the next WHAT did I do wrong . I need to know before the long process of saving again.thanks bryan
Man, I'm sorry to hear that. I have a couple of thoughts on what _might_ have happened. First, how many satellites did you have when you took off? It's good to have at least 10 or more to ensure good GPS. Second, were you near any large metal or concrete structures? Those can cause interference. Again, sorry to hear about that bad experience.
This didn't work for me last night! I downloaded the Bin, put it SD CARD and did the hamburger menu and it fails to find it. When I click check for updates it fails even when connected to WIFI. I don't know but this is trying everything in vain.
GOOD NIGHT EVERYTHING IS INSCRIPTED IN ITS CHANNEL AND I HAVE A PHANTOM 4 PRO PLUS WITH BUILT-IN SCREEN AND I WANTED TO UPDATE DJIGO 4 TO BE ABLE TO ASSESS PHOTOS ON THE PICTURE OPTION AND PHOTO 360 DEGREES BUT I AM NOT GETTING PLEASE HELP ME HELP .
Thanks, was going to order the Phampton 4 pro through amazon, but will hold off, until DJI can figure out this I agree with the gentleman below, one buttom, wait until a green checkmark appears and it says, Congratulation, go fly but check when done as another will be issued in a couple of hours.
I can‘t update my Database and i got everytime an error massage on Dji Go 4 App and on Assistent 2 For Phantom i Downgraded my Drone and Updated it and restored it but nothing helps!
That is correct. If you update your drone and then fly with a different battery, it will say "inconsistent firmware found" and then it will update the battery. But usually, this is quick and easy.
Thank you!! You rock!!! Everything in you controller firmware update was correct! It worked step by step as you walked me through it and now I am flying again! This was extremely important for me bc I need to drone a hotel in Key West next week and had no time to send it to DJI. I saved money and learned this valuable step to keeping my drone up to date and working smoothly. I will subscribe to "Ready Set Drone" immediately. Thank you! Sheppy01
O radio do meu phantom 3 apagou após atualização (controle não liga). Alguém conhece o problema e poderia me ajudar? My phantom 3 radio went out after update (control does not turn on). Does anyone know the problem and could help me?
Many thanks, you explained it in great detail, I was having the same problem :) Oh I have a question, I have my camera settings to shoot RAW but for no reason it changes to jpeg and the ISO goes back to auto, I only discover this problem when I upload the files, please help someone :)
Really great. No image Transmission Signal bothered me for some time since I bought the drone. Today I followed your instruction step by step, I got signal finally. Thank you so much!
Man, you are a life saver!! I updated the firmware on my drone (P4/PRO) and I lost my video signal and I had no GPS. I could still fly it but very limited distances. When I tried to update my controller with the memory card it wouldn't work. I forgot to unzip the file before putting it on the card. I should have known this. Once I unzipped it the updater on the controller found it and did the update. Now my drone works perfect. Thanks so much!!!
Awesome! I'm glad you were able to get it working!
For a company as advanced as DJI I can't help but wonder why they don't design these routines to be EASY to do rather than the bloody minefield it seems to be. I mean the sort of thing where a big red button comes onscreen and tells you exactly what connections to make and after that maybe a big blue button when you hit it, the whole shemozzlemaflip just goes ahead and does its clever stuff. Not everybody knows about zipping files for instance...
Being even mid-range computer-savvy shouldn't be a prerequisite to routine maintenance like this.
Oddly enough Ken's video was the one I watched immediately before this one. Maybe now when it happens to me I'll not be so inclined to panic?
I think if everyone paid attention to the .pdf on DJI SITE on " How to install updates" @ 4:24 things would go smoothly. No issues here..
Ian Gourlay a
I can only say...I AM VERY DISAPPOINTED WITH DJI. Good products but awful customer support, repair and software.
After sinking over $2,000.00 on P4P, Goggles, extras......I have a shaking, wobbling POS flying, I have done everything...re calibrated IMU, Compass, wasted hours searching and nothing.
Then, I purchased the HDMI module so I could plug the DJI goggles using HDMI port.....to find out that is only works with the USB port...so I need disconnect my Ipad.
First they told me to send the HDMI module, one month later they tell me there is nothing wrong with the module, then they tell to send the RC....another month goes by and they return it telling me that the RC has no problem. I don't think the problem is the goggles or the cables because I tried a monitor with the HDMI port and had the same issue....no image, just the OSD display and turns on and off between black screen.
THIS WAS THE LAST TIME DJI GOT MY MONEY, thank God I did not go for the Inspire 2....would be a double loss
I had the same problem, out of the box before ever flying, after updating the firmware, thank you so much for this!
For the DJI 4 (ONLY not any other) video telemetry issued I copied this from another forum and it worked to fix it perfectly. Had to try several steps several times but be patient. It works!
1) Install DJI GO 3 app from Apps store, launch app (at this time P4 is off until I say)
2) Select P3 Pro as aircraft (SE and Standard are wifi, not sure if this would make a difference), using the 3 dashes at the top right of the app press and hold for 10s or so. A new screen appears showing suggested current firmware of RC. Scroll down to firmware 1.6.0 select "Firmware Refresh". Wait for it to install then close the app and shut off RC.
3) Reboot RC, after a few minutes on shut off RC (not sure if this is really required, but it seemed right)
4) Open up DJI GO 3, Select P3 Pro and press camera (have the lightning cable connected to RC and iPad/iPhone). I had over 50% charge on my RC (btw)
5) Once in main screen with telemetry info wait a few minutes and press the Left upper area just next to the DJI logo saying "No xxxxxx connected " in red, this will take you to the Aircraft setup screen.
6) There you will see a warning message triangle, press this area and it suggests upgrading the firmware as you have 1.6.0 installed and the latest is 1.9.3
7) This started the firmware download and then with lots of beeps and blue flashing light the upgrade was a success !!!!!
8) On completion it will tell you to reboot the RC. At the same time I closed off the DJ GO 3 app.
9) Reboot the RC again. Mine complained at low battery so I did a second reboot and 3 white LED battery level lights came up as well as the RED LED indicating no aircraft bound.
10) Turned on P4 and launched DJI GO 4 app and BANG.... full signals on RC and Video feeds and NO flashing red/green led any more just solid green. So fingers crossed for her maiden flight tomorrow ( double fingers crossed)
I hope this helps others; note the DJI GO 4 apps does the same if you hold the 3 dashed lines for 10s or more. I did not try this route to roll back the firmware on the RC.
Thanks, this worked well for me!
are this is for phantom 4 advance?
This did not work for me. Downgrade firmware worked, would not upgrade firmware.
Thank you!! I was having so many Issues with getting it set up. Saved me from a week of frustration !
I'm glad you got it all figured out. When I did my update a couple of weeks ago, I just used the phone app and did the drone and then it told me that basically the controller needed updated so then I had to do that as well and all was good. Keep in mine mine is not the plus version that yours is so obviously something is played differently.
Yeah - sometimes I wonder if buying the "plus" with the built in screen was really the best decision...Thanks for the comment!
Sir than you so much. I am using a drone from my school grant and I had a "no signal" issue. The camera feed would not show up on the monitor but the camera still functioned. I thought I broke something and for the camera not being mine only made matters worse. Turns out it was just a simple firmware error!!! Thank you so much!!!!
Glad to hear it!
Thanks for posting, this will help me & lots of others out no doubt. Glad you got yours up and running. Happy flying!
Had to do this to a brand new P4P+. So frustrating why DJI don't tell you this to start with.
But thank you, your vid was fantastic help. Marky Mark
Glad to hear you got the issue resolved! Thanks for the comment!
Mark Turner How-do-you-do it if you don't have a Built-in screen my controller doesn't have an SD port
Thank you! The confirmation on how the cables are supposed to attach was a major help.
Phantom 4 Pro+ vs Phantom 4 Pro V2.0 - I downloaded the firmware for the V2.0 by mistake (duh). That file wouldn't extract to a .bin, but instead just a directory, and the pdf instructions say to just put the .zip on the sd card by itself. I was really frustrated until that facepalm moment when I realized it was the wrong firmware. The firmware for the Phantom 4/4+ does extract to a .bin and it worked immediately. No test flight yet, but I'm hoping this resolves a ton of issues I was having.
Have you noticed any new issues with the screen? I can’t get my fly safe list to enable to fly in a certain area. Why is this happening? I’ve heard that there’s no update for version one anthem for Pro plus
So glad you got it sorted!
Hey look! It's Ken!!
Ken Heron Cheek my previous comment on this video...Greetings from Douglas, Arizona 👍👍👍👍
Run. That dude is a super douche.
agreed, he voted for Hillary too
Ken Heron ?
Followed your instructions: format card, download latest firmware via website onto sd card, put the sd card in the remote, then started the process. All looked good, but at the end of the auto-reboot, i get an error "Update Failed: Error code:800". Any suggestions? Thanks!
You know if is there a difference between the pro and 4 ? Im having the same problem with the pixels, and can’t find a solution for it, or how to do it
Good stuff! I replaced my P4PRO gimbal and now I have no video. I;ve tried to update everything I can think of still no video. No errors shown "normal" status but no video. Black screen on mini Ipad. Thanks for any help
just FYI - you mean phantom 4 PRO but in your video description you wrote only 4 - which is a big difference. I have a 4 so your video isnt helping me at any issue i have with my drone right now.
decided to take my phantom 4 out for a flight yesterday after a few months of closet time, did the updates and it flew like crap! pixels all over the screen, and non responsive at times! luckily i got it back safely but this is ridiculous! it flew completely fine before these so called "updates". can't they just leave good enough alone. if it ain't broke don't fix it.
Were you able to fix it?
I have this same problem am yet to fix mine ive tried almost everything
Pls, I want to know if you have fix the problem , I have my for 2weeks now it came with the new update and I am having same problem
RO DION yes i was able to fix it there is another tutorial here on youtube i followed it solved the problem.
Og Nnamdi pls can you share the link pls I need ur help
Thanks so much, would never have figured it out without this great video!!!
Hello , kindly help . Guide me on how I can update my smart RC, I use it to fly phantom 4
At DJI they did not have the Phantom 4 controller firmware.
Hey Last week I did the same thing. Went to fly my Hanson 4 Pro for the first time in a week or two and I got the message inconsistent firm ware do I swiped it and updated the drone.. now I have really bad not very usable video stream on my controller. I tried a lot of things but I haven’t tried to update the controller firmware yet. I will try that next. My Mac has the latest OS on it and they do not have a DJI assistant version that will run on a new Mac that also has Phantoms drone. DJI failed to support Phantoms on the new version of assistant 2. I can go by a PC I suppose. This is the first drone night mare firmware problem I’ve had in years
Mine is doing the same, but mine is a phantom 4 not the pro, cannot find the firmware!!! How do i fix it, lots of pixels like yours green screen
JP Matatan did you ever find a fix? I have a P4 also with same problem, no micro SD card slot on the controller. I'm way beyond pissed at DJI true lack of accurate programming and lack of real support. You see all these videos and people say and Bam it works... Not here.
It doesn’t show an update on the app for the remote for me,, so I don’t know how to fix it, the light blinks on the remote like yours used to
JP Matatan did you later fix this ?
did you find the solution ?
Hi Tnx so much i was crasy to find why i have the same problem with the video then i fund our tuto...... tnx again from france
My P4P+ recently had a firmware upgrade to the AC and RC, but now the touch screen camera controls intermittently freeze, so hugely annoying . Any ideas as to how I might resolve this would be much appreciated ?
Good evening, I have a phantom 4 pro, when I turn it off after 10 meters it lags and loses the image while I have a full signal
Many thanks for making this video. After getting off the phone with DJI tech support today, I am shocked that they still havent addressed this problem. My question: When you downloaded the .Zip from DJI, where did the .Bin file show up? When I open the .ZIP and look at those contents, there is no .BIN anywhere to be found. The struggle is real over here........
I'm a new user of phantom 4 pro, only 1 month and i had a problem with image in my smarthphone like you shows. After firmware update the images on my smarthphone are completly black. my English knowledge is a little poor. could you write please an essenzial list of steps to improve the image quality of connection between smarthphone and phantom 4 pro? only essenzial steps please . Best regards, Giuseppe
Quick question.. do you know if the latest firmware for the P4P+ fixed the issue where users cant hide the OSD from the HDMI output feed? this is specially used when been used to TV broadcasting, so the output video is clean with no UI stuff. There are so many complaints in the forums, but this happened last year, and I cant find anywhere if this issue got fixed or not. Im planning to buy the Drone only if this feature is available :(
I have the p4pro+ and I have another controller and I would like to use them both of them separately for the same drone is this possible
Thank you so much for this. Appreciate your time and effort.
Thanks for watching and commenting. 👍
just a heads to save people tons of time who are having problems with distance-video issues. if using a android tablet or phone the type of cord (charging cord) does make a difference. i had problems and switched from gas station bought cord to the original verizon cord and worked flawlessly.
Glad you fixed your issue!
Yeah - it was a challenge to fix, but glad I was able to do it. Hopefully the video helps others with the same issue! Thanks for the comment!
best video on youtube. many thanks! saved my ass and work
There was not an adapter with my phantom 4 pro. i checked the in the box list and this also does not list it.
Hey I was hoping you could give me some insight for an issue I’m having with my camera/screen. I have flown my new P4A 5 times. No issues. But I notice that the “real time” play back will slightly lag or glitch and I thought it was only going to be on my phone, but I saw this issue when I was editing on FCPX also. What happened during editing is a black screen slides across my footage from top to bottom really fast and ruins my shot. Have you experienced this or heard of this?
I tried everything but it is not working the controler wont see that there is a file. i tried 2 different sd cards and formated them in the drone in the controler and on the pc but it just wont see that there is a file with an update.
Thanks for the video. I had this exact problem and this helped a ton.
What do you do if the controller doesn't have a micro SD card slot?
I had that problem with my tablet. The solution was to use a more powerful device. Video feed is low priority and if your mobile device can't supply the CPU power, you won't get video or choppy video like that. I switched from a 8 year old tablet to a 2 year old Samsung Note 5 and all was good after that.
So, I had a failed update with my Phantom 4 Drone standard. Everything is working fine, but the camera is not sending an image to the screen. I've tried resetting the camera, adjusting the settings, reformatting, etc. Nothing... Will DJI Assist help me fix the bird?
I would definitely try DJI Assistant. I would also suggest rebinding the remote with the drone, that might do the trick.
@@readysetdrone Awesome! I appreciate the reply. I haven't had time to reset the remote yet, but I'm going to try today.
the strange thing, is that the indication light next to the sd card slot on the drone is cycling green, orange, red. Like I said, it seems to connect to the remote, but the remote is not able to see what version of firmware is on the drone. whenever I go into the software through the remote, and hit "Check firmware" for the drone, it just keeps thinking, and never sends back a result. The app doesn't freeze, and the drone is still communicating with the remote, but it stays in that green orange red blinking phase.
The other symptom I'm having, is when I connect my phone directly to the drone, it doesn't communication with the app.
Thanks for your clear concise video! It's much appreciate.
Do you also have issue with it resetting your camera settings after each firmware update?
Hello, I'm trying to download an update but I keep getting the error saying " insufficient storage 2G " I have a memory card in the RC. The. Current version I have now is V01.02.02.00 can you help me with the problem I'm having? Thanks...
One question - are you on wifi and is the wifi connection good? Also, do you have the drone and control connected via USB? It can't be the larger USB connection, needs to have that OTG cable with the smaller micro USB on both sides.
Updated firmware yesterday . After rebooting and taking up about 50 feet I get downward infrared warning amd to land . Wasn’t having problem the day before. Any ideas of what may be causing this
Could there be something blocking your IR sensor? Are you flying over grass? My suggestion would be to reboot everything, take it out to a grass field away from concrete/buildings/etc and give it a try there. Also, be sure to do a compass calibration. Hope that helps!
How can I do this for the DJI Spark ?
Hi there! I've got a Phantom 4 but my controller doesn't have a micro sd card.... it has usb and micro usb only... In this case what do you recommend?
cheers!
this only updated my controller and not the actual drone, any idea what i did wrong?
Instead of connecting to your PC and downloading, couldn't you do an OTA update?, as you seemed to have the option on the controller to update through WLAN. Would save all the connecting and disconnecting cables if you could :-)
Seems DJI have made this unnecessarily complicated. While not in the same class as the P4 range, my Xiaomi Mi drone 4k does all firmware updates with just 1 click. That is 5-6 different firmware's for Quad, RC, gimbal, camera, battery etc. It's certainly not without it's own issues though!
I guess in the end, the more technology they have built in to these drones, the more potential issues and quirks!
Cheers
As a newby I'm so bummed tha DJI has made this so complicated and no instructions on what to do. Thanks for sharing this. I have no signal after updated and my controller just beeps. So frustrating
Did you update the controller and the drone? It should be easier to do if you have a regular P4 or P4Pro...I think part of the complication is with the P4Pro+
Nope P4 has exact same issues but we don't have an mcsd slot to download any firmware and local install. We are at the mercy of the app that buy the way will not download the new firmware, only the old to downgrade but once you've attempted to upgrade the remote will not accurately see the firmware on the P4 and says you have an outdated firmware on your P4 even though you've updated it through the assistant app on a PC.
Thank you so much, I was getting very frustrated trying to update the controller through wifi. I haven't flown it since the update.. but I no longer have a grey monitor and everything seems to work well again! Much appreciated
This was a great walk through Kell. I’m planning on purchasing the phantom 4 pro 2.0 soon, haven’t decided if I’m going to do the one with the screen or not on the controller. I’m just so used to using my iPad Pro 12.9 now. But if I do get the one with the screen, this was a great vid to let people know if they have the same issue you had. 👍🏾👍🏾👍🏾
Wow, I got the spark, my first real drone and if I like the flying aspect with the photography, I would get a phantom 4 pro as it as the 20MP camera. Maybe might get the Mavic as it transports easier. But you're video really does highlight the complexity of ensuring everything, the software is updated and understanding the all the little nuances with the software combined with the hardware.
Anyway, I really enjoy your video's. They are very informative and one of the reasons, why I got the Spark.......sorry not from RSD but straight from DJI..... the red one.... Thank you for a nice video.
Awesome! The Spark is a blast! Glad to hear you like it.
Thank you for posting the fix.
When I have upgraded the firmware on the Mavic, the DJI Tutorial shows you how to update the firmware on both the Mavic and controller at the same time.
Is this not available on the Phantom 4 Pro ?
I think it was more complicated because I have the "plus" version with it's own screen, which means that updating the controller is a bit more of a challenge.
You know that's what I was thinking. So glad you got it figured out. I am saving my nickels and dimes to get a Phantom 4 or maybe wait to see it's replacement.
Hello mate. Any ideas on downgrading to an earlier version of firmware for the drone? My upgrade today has all but bricked it.
Ouch - have you tried going back to the last (previous before you installed this one) firmware using DJI Go 4? You should be able to do that.
Thanks for your quick response. I have tried rolling back the firmware, but DJI Assistant 2 cannot do it. DJI have locked us out of that here in Australia. Maybe everywhere. I think I will have to wait for someone to discover a hack to bypass the DJI upgrades that seem to be nothing but buggy. Having said that, you seem to have a good upgrade that is working fine. I hope you do not get the same problems we get here. I sincerely hope you do not get any issues with flight stability, "phantom no-fly zones" etc, that we are experiencing. My farm is 2 km away from the Civil Aircraft Safety Authority (CASA) indicated NFZ (a small rarely used airport), yet DJI are saying the NFZ encompasses an area about 7 km radius from the airport. Australian law is 5.5 km radius for an airport. DJI have dropped the ball here.
Love your channel mate. Thanks for a professional, friendly and informative method of getting us novices up to speed.
Have a safe and happy day mate.
Hello Sir ,am Joshua from Tanzania. I have Phantom 4 Advnc ,it says Navigation system error check redundancy state
I am using phanthom 4pro v2 and iPad meni4 I had recorded vedios in internal memory with 4k quality but here there is problem that is when I back up all these recorded vedios I am getting all these vedios with 720pxl I want all these vedios with same quality what ever I done ft so how to back up all these with 4k quality
is this working in phantom 4 advance drone
Can tou help me out...i try to do the factory reset on my 4 pro plus after reset is asking me to login but i cant not connect to the wifi. How do i connect to wifi thanks
You should be able to connect to wifi through the app using the touch screen. If that doesn't work, I'd using DJI Assistant (free software) on your computer. If you still can't sort it out, contact DJI tech support. Good luck!
will my phantom4 pro connect using an android tablet
Does the update changed anything in the screen? I was interested to buy the pro plus but seems that has too much issues to update and cannot inatall third party apps
Honestly, if I could do it again, I would not buy the Plus - it has more issues than a regular phone and is more difficult to update. I would go with the plain old DJI P4Pro and skip the plus.
Thank you for your suggestion
Having stability problem after crash, no damaged to drone actually except propellers, someone saying that its an motor problem and motors need to be replaced, is it true reason behind that?
When you say stability, do you mean it will fly, just not level? Please provide more details on what you mean and I'll see if I can offer suggestions.
when it fly in the air it moves automatically to one side, and I am facing this problem only after crash
Thank you so much for this video, you saved me sending back to DJI only for them to tell me it was a software issue. Why does my controller not automatically update or install updates over wifi? I don't know, but at least now I do for the future. Many thanks
Thank you for this, I just got a new P4P+ and thought I had completed all the updates, registrations (DJI & FAA) for prep prior to the first flight, I got down to a site for my first flight and was getting the same pixelated screen. I too tried to change the frequency. Did not help, So I hope this does the trick. I will be installing the bin file in the am.
The other problem I have are pop ups that say fly with caution, magnetic interference. I had calibrated the IMU on a level surface then the compass and still get the interference pop ups. Maybe this will fix the issue also. I know the area I am flying is ok as my Mavic Pro has no issues when flying at the same location. Thanks for all the great information.
What about for pro? My remote doesn't have built in screen so no sd card port?
I own a Phantom 4pro+ too... So after the August 2017 firmware update my video image was completely pixelated... After searching the forums I learned that by doing a factory reset on the controller the video issue would get fixed. I did that and the issue with the video disappeared. Thing is that now the telemetry isn't accurate, the indicator LEDs on the drone blink 4 times green as it should be, and two long red blink ones... The interesting part is that the application aircraft's status tab shows all systems working normally🤔 . I called DJI customer support and they told me to perform an IMU and Compass calibration to fix the issue. I did it, but the problem still happening. The aircraft also shows a negative number on its altitude gauge with the aircraft still on the ground. I'm stuck with a $1700 paper desk weight in my house because under this conditions my drone is not reliable for flying. Ohh, another thing is that the gimbal moves by itself side to side really slow without any inputs...🤔
Anybody experiencing something like that? I need help desperately..
Wow...that sounds terrible. I have a couple of thoughts. First, I know that the P4 (and all other DJI drones) are very susceptible to magnetic interference. Be sure you are not on concrete with rebar, near power lines, etc. I have seen the negative number on the altitude before when I start it in one place (like on a hill) and then move to some place lower...but never on start up. The camera thing is weird. My only suggestion would be to do the reset again, update to the latest firmware, then go calibrate everything out in a big field - away from any possible interference. Maybe hover it 5 feet in the air for a bit to see if it is stable. I wish I had a better answer...please let us know if you manage to get it fixed.
Ready Set Drone I'm going to try that and let you know!... Thanks!
Good luck!
Ready Set Drone thanks
"Ready Set Drone" I don't have an updates option in system settings!!! Any thoughts? Thanks for the instructional video, this is the closest i've found to solving the problem.
What are you flying Phatom 4 Pro Plus?
I am really having issue controlling the phantom 4 Pro. Recently bought, like a month ago. From last 2 days it’s really giving me hard time. Just right after starting and about 3 feet it doesn’t even stay at one place.. it’s keep moving... even when wind is 2-3 m/h. I had a chat with customer service and they said do the firmware update, IMU and calibration. I did all that but nothing is changing.
ua-cam.com/video/Fq6BcSYPjb8/v-deo.html
I have a P4P and have same issue. I have the standard remote, no sad slot on remote.
Yesterday, while I was updating firmware, and calibrating compass and IMU, after everything was done, rebooted both the bird and the RC, then suddenly, the bird was not connected with the RC anymore. The battery status was showing as Unknown, GPS was not communicating, the camera screen was showing the bird as not connected, etc. I was frantically trying to figure out, what could have possibly gone wrong. Tested everything, no result. It kept saying that wi-fi was turned off, and needed to be re started. Suddenly, I realized that I had left my cell phone out in the car. So, I went out and brought the cell phone back. It was dead, so had to put it on charger. As soon as it got some life back, I turned it on. everything was back to normal. The bird was back on line, and communicating with RC, the GPS satellites were back on, camera was responding. Even the Flight simulator was responding. I don't know if all this had anything to do with the fact that I am using my cell phone's wi-fi network, and since the phone was not around, and was dead, it dropped all signals, and the bird started playing dead. But then again, just to test this thought, I turned off the phone completely, but the things were all working normally. So, I thought, I'd just toss this in and let all you experienced guys tell me I was wrong.
Do you have solution for phantom 4 ? I have same problem, but the problem is , at dji.com they didnt provide firmware to download .. thank you
hi, resolved the problem???? I have same problem in phantom 4
I HAVE A MAVIC PRO FOR 5 MONTHS AND NEVER DID A FIRMWARE UPDATE AND IT FLIES PERFECT. MY UPDATE WAS TO CHANGE THE MUSIC AND HELP ENHANCE THE GOGGLES, BUT TO FLIES PERFECT, DOES EVERYTHING, I MEAN EVERYTHING ITS DESIGNED TO DO. IM AFFRAID IF I DID A FIRMWARE UPDATE I WOULD HAVE TO TAKE A PICTURE OF IT AS IT WOULD BE THE LAST I WOULD SEE IT
Hi I have the same problem with my phantom 4 drone. Do you have a video on how to fix this same problem on a phantom 4 drone. Thanks
an3n4 we are having the same issue. Would love to know if you find a fix!
I'm having the same problem
I am having the same problem too!
Hallo, Reiner here from Germany. Have near the same Problems then you with the Controller.....but how/ wich Format you have to Format the micro sd card?. My English is not so good, and i try to understand, but it was a little bit to fast. Thank for help, and sorry about my English
Reiner - have you tried using DJI Assistant with your computer? It is a big help in troubleshooting software problems.
Use the P4 to format the card when it is in the P4. This will put the correct format on the card.
Damn it's a chore figuring out how to update my P4P+ thank goodness for this video and the comments
Glad to help!
I saved up for over a year and sold stuff to get my first phantom 4 drone I was so excited. I started it up it went up to about 50 feet and it shot off like a rocket and never seen again I was so pissed and shocked excited one moment and cry the next WHAT did I do wrong . I need to know before the long process of saving again.thanks bryan
Man, I'm sorry to hear that. I have a couple of thoughts on what _might_ have happened. First, how many satellites did you have when you took off? It's good to have at least 10 or more to ensure good GPS. Second, were you near any large metal or concrete structures? Those can cause interference. Again, sorry to hear about that bad experience.
Ready Set Drone thanks for replying yes I was near a large tower. So sad. Thanks again
I have the exact same problem on my P4 Advanced however I do not have the controller with the screen
All you have to do is connect the controller to Wi-Fi without the drone on go into settings and update firmware over Wi-Fi
Do I have to turn off my wifi on the screen to download via the cable
My problem is the controller is not charging and refuses to update when the charge is lower than 20%
so.. it's impossible for my to update / restore
Lost me with the SD card, no slot on my controller :(
yes, no fing slot on a p4p
It’s only the pro control box that has it
This didn't work for me last night! I downloaded the Bin, put it SD CARD and did the hamburger menu and it fails to find it. When I click check for updates it fails even when connected to WIFI. I don't know but this is trying everything in vain.
GOOD NIGHT EVERYTHING IS INSCRIPTED IN ITS CHANNEL AND I HAVE A PHANTOM 4 PRO PLUS WITH BUILT-IN SCREEN AND I WANTED TO UPDATE DJIGO 4 TO BE ABLE TO ASSESS PHOTOS ON THE PICTURE OPTION AND PHOTO 360 DEGREES BUT I AM NOT GETTING PLEASE HELP ME HELP .
Stop yelling !
Thanks, was going to order the Phampton 4 pro through amazon, but will hold off, until DJI can figure out this I agree with the gentleman below, one buttom, wait until a green checkmark appears and it says, Congratulation, go fly but check when done as another will be issued in a couple of hours.
I can‘t update my Database and i got everytime an error massage on Dji Go 4 App and on Assistent 2 For Phantom i Downgraded my Drone and Updated it and restored it but nothing helps!
do you need to use WiFi when you update from a micro sd card?
I'm not sure that it's required, but it's always a good idea.
Can that built-in monitor be disconnected so an iPad can be used?
Not on the P4Pro+ In this case the monitor can't be swapped out.
Thanks to your video I've sorted my drone ,,, Great video
Dear Mine is Crystalsky but the process is the same . Thank you a lot.Solved
Sir can I ask for mini fpv drone ??😓🙏🙏🙏
Plss reply
Plss🙏🙏
Reply me pls I really want fpv drone I want to join fpv race !!
🙏🙏🙏🙏
Buy one
Thank you!! this tip worked!
Can anyone tell me why I'm not able to connect to more than 4 to 6 satellites with my Phantom 4
Good info, Thank you very much!
I heard that even the batteries themselves (at least on the Mavic) need to have firmware updates. Does anyone know anything about this?
That is correct. If you update your drone and then fly with a different battery, it will say "inconsistent firmware found" and then it will update the battery. But usually, this is quick and easy.
Thank you!! You rock!!! Everything in you controller firmware update was correct! It worked step by step as you walked me through it and now I am flying again! This was extremely important for me bc I need to drone a hotel in Key West next week and had no time to send it to DJI. I saved money and learned this valuable step to keeping my drone up to date and working smoothly. I will subscribe to "Ready Set Drone" immediately. Thank you! Sheppy01
hi sar my Name Raju From India Telenaga Vikarabad My Drone Phantom 4 v.2.0 Problem is image transmission signal weak & remote control signal weak
Having the sane problem on my mavic pro. Hopefully it works for it
O radio do meu phantom 3 apagou após atualização (controle não liga). Alguém conhece o problema e poderia me ajudar?
My phantom 3 radio went out after update (control does not turn on). Does anyone know the problem and could help me?
Many thanks, you explained it in great detail, I was having the same problem :) Oh I have a question, I have my camera settings to shoot RAW but for no reason it changes to jpeg and the ISO goes back to auto, I only discover this problem when I upload the files, please help someone :)
My drone is showing a problem of navigation system error.. Wat shud I do?
Calibrate the compass and make sure you are not near any large metal structures or concrete (which has metal rebar in it).