Benötigen Sie Hilfe bei einem DJI Produkt? Kein Problem einfach kostenlos kontaktieren. Persönliche Anfrage stellen: www.coptertec.... Preisbeispiele für eine Reparatur: www.coptertec....
I want to say thanks a lot for this video. I managed to strip down my mavic air to replace the rear left leg and now I'm up flying again! Can't believe I did it! Cheers!!
Douglas Ferraz Hiya. As you've read from this video I have bought, replaced and fixed my mavic air using this great video. I can only say that I bought my replacement leg on eBay but I've tried to find something similar for your needs. Unfortunately I can't see anything now but maybe you can. It cost me roughly £80 with customs cost etc for just the the rear leg! Good luck
QUAD FLY thanks brother. I am in the USA, I looked online the options were from aliexpress and Ebay. I am scared of those been fake and not work correctly. That is why I wanted to buy from the same place as someone who already had positive results. Since you bought your from Ebay I am assuming it's a 3rd party part not original and it works fine. Right?
Douglas Ferraz fixacrash.com/ bought mine from here I discovered. Hope you can get sorted. Watch strip down video carefully and mind the fact you have to solder two wires of new leg.
Phantastisch! Bildqualität, Kommentare, Know-How - alles gerade richtig, nicht zu viel und nicht zu wenig. Eins der besten Teardown Videos das ich kenne.
I came to this video after crashing my Mavic Air and breaking the left rear motor arm. Although I speak English I was able to follow the video. Your descriptions with pointing out components made it possible to follow. By far the best video on You Tube for the Mavic Air. Well done. Hope to see an English version real soon
I speak no German however I repaired my Mavic from this wonderfully informative video by following the teardown until I found the problem Great stuff thanks :) was a life saver :) :)
Vielen dank, für die Klare problemlösung. Hab die IMU bei AliExpress gekauft für €18. Mit deinem hilfe via You Tube, selbst die IMU ersatzt. Super einfach, und die Mavic Air ist problemlos wieder in die Luft ! Danke!!
CopterTec crashed mavic air into a tree (sideways!) and snapped the rear left leg off at joint. Wire hanging in there but must be disconnected a bit because I'm getting an rcs error. I've ordered a spare leg and hope to fix myself. Have you got any recommendations? Cheers
Vielen Dank für das Video, ich musste den Motorarm vorne links austauschen. Nach Reparatur startet die Drone und fliegt, allerdings Steuerung nach vorne und nach hinten nicht möglich, alle anderen Richtungen (seitlich, hoch und runter, Achsendrehung) in Ordnung. Woran kann es liegen? Danke für die Hilfe.
Hallo, das freut uns zu hören. Klingt als würden Sie in einem kleinen Raum versuchen zu fliegen. Dann blockiert das Vision System diese Manöver. Am besten eine große freie Wiese suchen, damit nicht der nächste Arm kaputt geht :-).
Thank you!!! Broke a rear arm axis after an unfortunate loss of signal timed out under a tree. Was actually impressed at the self inflicted beating the drone repeatedly took trying to RTH before crashing to the ground. Was able to follow along quite well without language comprehension.
Amazing video, thanks. What adhesives are needed for reassembly besides the white PU glue? What, if anything, was used on the cable plugs and fan motor? Are any other supplies needed for reassembly?
Thanks for your nice feedback. You only need the white PU glue. The fan can be assembled with the same glue. Also the silver protector stripes above the plugs.
Amazing video, I had another problem the drone LEDs are blinking red, yellow, green (self-diagnosis) and I can not connect to DJI Go or DJI Assistant. I also can not press the back button to connect with WiFi.
@@CopterTec The only thing I can think is that I turned on the remote id two days before and the (self-diagnoses) continue to run at the start-up. (green yellow red).
Super great video. It's understandable even in Germain! Very clear and illustrative. One question though: Which part is usually unusable when when fallen in fresh French water?
Hallo.Ich bin Slowake und kann kein gutes Deutsch. Ich hatte einen Unfall mit mavic air.Kamera ist in Ordnung. Video-Uploads! aber der Gimbale-Motor funktioniert nicht.Kardan muss nach dem Austausch installiert werden?
hi. der weiße Kleber an den Lötstellen für den Motor dient zu Zugentlastung nehme ich an? Was ist das für ein Kleber, fühlt sich wie Silicon an. Bin gerade dabei den Motorarm hinten links zu wechseln und würde die Kabel gerne mit gleichem bzw. ähnlichen Kleber ankleben. Könnt ihr mir verraten was das für Klebstoff ist? Vielen Dank
thanks to this video I was able to restore my mavic air that went for a swim and was able to fly out of the lake XD we´ll see how long it lasts and if there were any long- or short- term effects in the overall performance. THANKS for sharing this content
Top video, hat mir sehr geholfen beim Tausch zweier Arme. Schade das du den Arm nicht gezeigt hast mit der Antenne, da war ich kurz Ratlos. Wenn die Drohne keine Fehler mehr anzeigt, kann man sie Problemlos starten ? nach dem Kalibrieren natürlich
Hallo, das freut mich. Ja die Antenne wird ja oben beim zerlegen entfernt :-). Beim Mavic 2 sind wird gründlicher ;-). Wenn kein Fehler mehr da ist kann es los gehen. Wir machen aus Sicherheit immer folgendes: - Firmware Update - Gimbal kalibrieren - Vision System kalibrieren (via DJI Assistant 2) - Kompass kalibrieren
@@CopterTec okay super, erste Schwebezug in der Wohnung lief ohne Probleme. Ich hab leider nur die Air und weiß nicht ob der aufbau bei anderen Modellen wesentlich abweicht, aber trotzdem 1A erklärt. Das hat mir einiges an Geld erspart denke ich
Hey! Great video, except the fact that i dont understand german .. What is the name of the cable you point at, at 11:00, right after you point at the camera cable? My camera is working, but I cant move it with my controller anymore, and its not stabilizing. I seem to have damaged that said cable when I had to change my rear arm.
@@CopterTec No worries, you're a German company so^^. Ah yes, I havent been able to find one online that looks the same as the one I have. My camera wont move or calibrate, so I guess the cable must be damaged. You dont happen to ship to Norway by any chance?
@@Dernel2 Norway is no problem. Are you sure that the problem occurs from this cable and not the silver one? Is there a video link and can you enter the video settings?
@@CopterTec I'm not 100% sure. Video link is working, and video settings and camera settings are adjustable. The gimbal calibration always fails at 10%. Its possible that I damages that cable when i changed one of the arms. When I google "mavic air flat cable" I cant find any cable that looks like original.
@@Dernel2 Ok that can also happen if your signal wire (silver one) is demaged. I'm not sure if you can buy this cable in any consumer shop. We got this product directly from DJI.
Hallo, den Kamerasensor oder einen anderen Sensor (Gyro, Kompass, usw.)? Ich denke ersteres dürfte nahezu unmöglich sein (das zweite sehr schwer wenn nicht identisch). Es muss ja nicht nur das Maß sondern auch die Belegung der Pins identisch sein. Desweiteren muss die Ansteuerung der Software stimmen, sonst gibt es nur eine Fehlermeldung...
@@CopterTec Joa fehlten iwi etwas offenes was man customizen kann. ZB ein austauschbarer Gimbal mit Kamera. Hat natürlich keiner der Großen Player Interesse daran. Die Kamera der Mini ist zB grottig gegen das was zB im iPhone oder Pixel4 verbaut wird, bei gleichen Maßen. Technisch wäre selbst eine 4k 60p Drone mit unter 250g machbar.
@@Krautmaster86 Machbar ist vieles, aber die Frage ist, ob DJI das auch möchte ;-). Leider ist das ganze so aufeinander abgestimmt, dass ein Austausch schwierig seien dürfte.
Thank you. Your video very helping me, i have successfull to change my right arm. But now esc error. Do you know how to fix it? By the way I’m Yusuf from Indonesia, nice to meet you
Cooles Video. Hab eine Frage, würde es auch über euch machen lassen: Bin mit meiner Air langsam gegen eine Hauswand geflogen.. sie ist auf den Boden gefallen. Nun ist im einen hinteren Arm ein kleiner Luftschlitz genau an der Stelle zwischen Arm und Body. Der Arm an sich ist fest, die Rotorblätter stehen nun aber auf der Seite nun minimal näher zueinander als auf der heilen Seite. Ist das sehr bedenklich? Kann das wieder hergestellt werden und mit welcher Reparatur muss ich rechnen? Schonmal lieben Dank im Voraus. Und Abo ist raus :-)
Hallo, das klingt nicht besonders problematisch. Handelt sich wahrscheinlich um das Drehgelenk. Am besten einfach mal bei uns auf der Homepage das Formular ausfüllen. Danke.
Hello, the compass is on top of the Core Board at the back right corner. It's close to the rear backward vision system connector. The compass is the square IC. Pro tip: Use a magnet to locate the compass. You will see a big deflection in the app if you are close to the IC.
@@CopterTec Hello friend, I have the same doubt with the compass in the Mavic Air 2/2S and with the Mavic 2, the compass in these models is also integrated into the main board? Thanks for your answer
Thanks for this great video, I wanted to know if you can help me? I have a mavic air and I can not calibrate the compass all the time it tells me that I must calibrate it and it always throws error
CopterTec. I ordered new arms and followed your video and wanted to know what the white stuff is on the wires? I think an anti-vibration type substance, but my problem is that its on the solder joints! Will that ruin the board if I de solder the wire points with the white stuff on them! By the way, GREAT VIDEO! I don't know German but the video was so precise that I was able to follow with very little problems! THANKS
Hi, the white stuff is PU glue like Sikaflex (or Wacker). You can remove the glue with pure alcohol. But it will not ruin the board... no fear :-). Thanks for your nice feedback. You are welcome.
my1948hummer Hi guys, I want to replace the right front and rear arms on a mavic air myself. Where do I get them? Thanks if you can help. I'm in the USA. Get video by the way. I hope I get get my hands on the parts to fix it.
Bei der Komplexität der Mavic Air. Glaubst Du an die Gerüchte, dass es im März noch einen Mavic Pro II geben wird. Oder ist die Air der diesjährige Nachfolger des Pros?
tinyentropy Das weiß ich leider auch nicht. Es könnte vielleicht etwas größeres aber auch faltbares geben (zwischen Mavic Pro und Phantom). Dafür dann aber mit einer genialen Kamera. Aber das ist nur meine Vermutung...
Hi, sorry my French is not the best. You want to remove the glue/plastic above the screws? You can use a screwdriver. Important: The newer Mavic Air drones (sind 2018) come without these screws.
Great video, thanks!! I'm having a very hard time reattaching the rear right arm, which was somehow pulled out. I removed the 2 screws, but it won't seat correctly, and I don't want to force it. Any advice? Thanks in advance!!!!
@@CopterTec thanks for the reply. It was the 2 screws at 25:45. Looks like there's a piece of metal inside the arm which was/is bent :/ Don't think I'm able to repair that one. DJI Care Refresh 1 out of 2 left, o well. Video was still very helpful for my next screw up.
@@adambaldwin9544 Hi, yes this is a metal part. You can buy it for round about 15usd. But you need to solder the motor cables. Good solder skills are important... Or dji care :-).
@@CopterTec everything worked out. Had to keep the original camera module. Placed it inside the new gimbal. After calibrating with dji app, pitch and roll were perfect, but yaw was way off to one side. I had to manually adjust the yaw quite a bit in the gimbal advanced settings
@@ginocozijns3075 Yeah sometimes you need a "manuel adjustment". But nice that everything went well.
4 роки тому
Hi! Can you help me about camera cable replacement? Crashed the drone, signal cable teared. Replaced it with new one, but the camera is depending on (but I don't know how) how I put it back to the gimbal is tilted more or less. Is there a special way to put it back to the gimbal? (gimbal's camera keeping part is broken a bit but it doesn't seem to effect anything and I can put back the broken part). Thanks
@@CopterTec that's not good news. Thanks for the help. By the way that's what I bought: www.ebay.com/itm/253810742052 Is there any way to solve it or do I have to buy a full original gimbal from DJI? Only problem it's very expensive, half of the price what the drone worth now
Hallo, woher haben Sie das Gimbal bezogen? Leider sind 95% der angeboten Gimbal auf den bekannten Shopping Platformen nicht funktionstüchtig bzw. defekt. Existiert das alte Gimbal noch? Am besten einmal über unser Formular eine Anfrage stellen: www.coptertec.de/produkte/dji-innovations/
@@CopterTec ich glaube das war aus den USA. Das alte ist noch vorhanden. Es war auch noch ein Siegel drauf und es bewegt sich auch nach unten und oben aber dann kippt es nach links. Auf die Kamera kann ich auch zugreifen. Habe mal was gehört das man es mit einer speziellen Software von dji kalibrieren muss. Ich werde aber trotzdem mal das Formular ausfüllen. Danke
@@JustfourPrint Die mit den silbernen oder goldenen Aufklebern (glänzend) funktionieren ganz sicher nicht. Das kommt von einigen asiatischen Lieferanten, welche zur "Beruhigung" der Kunden diesen Siegel aufkleben. Das wäre ungefähr so, als würde man den Prüfsiegel auf das KFZ Kennzeichen kleben, ohne vorher das Fahrzeug zu begutachten.
At 32:36 You point to some thing on the undercarriage next to the downward sensors with your tweezers what is that? mine has a hairline crack wondering if you can replace just that little piece or if I should replace the whole body?
@@CopterTec yea my Magic air still woorks but it has a hairline crack the peace that the guy points to in the video that I described in my first post is it possible just to replace that little piece? or do I need to buy a whole new shell?
Hi CopterTec, very nice and detailed video. I crashed my Mavic air into sea water and now it displays ESC Error, Battery Signal Error and the gimbal camera does not rotate. it was there in water for about 10 secs. Do u suggest i send back drone to dji or it can be repaired by myself. The drone is just 2 weeks old.
CopterTec Oh, I saw the end. I just didn’t see it turned on. 😜 I wonder how many people will want to change out the color panels, like from white to red. I saw you broke at least one tab taking the top cover. What we’re in the bags at the beginning of the video? My German is a little rusty.
Haha yes next video I will turn it on :-). Yeah one part broke on the cover. The problem: I opened the cover for round about 10 times. So the material is a bit exhausted. This is the normal combo without any extras. Only the mavic air with one battery, 8 propellers in total, charger, usb c cable and propeller cage.
hi, am trying to open the top cover, but what screw driver will i use in removing the screws in the gimbal its not flat nor cross screwdriver. it looks like aa little metal ball not a screw
Super Video, damit konnte ich alles notwendige freilegen, um meine gebrochene Drehachse hinten auszutauschen. Am Loslöten der Rotorkabel habe ich mir etwas schwer getan, am besten man nimmt eine dickere Spitze bei 450 Grad und hält kurz drauf.
Dankeschön :-). Das Oszi ist schon etwas älter aber immer noch top. Der Name von dem Teil lautet DSO Quad und kommt von der Firma Seeed. Mittlerweile gibt es (glaube ich) auch einen Nachfolger davon. Noch interessanter finde ich allerdings das LabNation SmartScope für PC/Smartphone. Grüße
Vielen Dank für das tolle Video. Jetzt konnte ich endlich das Linsenglas selber auswechseln ohne dass ich eine neue Kamera kaufen musste ;-) Ich bin gespannt ob sie wieder funktioniert wenn ich sie einschalte ;-)
@@CopterTec May be you can advise me what to do. After my drone fell down it can find only 6-8 satellites and never more. I did all available calibration for compass, IMU etc. All indicators work well, no error messages BUT when I'm trying to fly it can't find more than 8 satellites even far from the town or in the forest. I've tried it in different countries and everywhere I faced this issue. Moreover, sometimes it can fly by itself to the left or straight. How do you think is it a problem of GPS module? Because it finds satellites but in the place where another drone finds 16 my drone finds only 6. Please help :)
@@SlidVibe Hi, sounds like your GPS only work with GPS or GLONASS. GPS > US system / GLONASS > rusian system. Normaly the GPS module find both systems and so you have 16 satelites. My first idea: call the DJI support and ask them (warrenty case).
I'd never thought that the interior of a drone such as Mavic Air is so complicated~ funny vid but hard to demolish it for an ordinary person just not specialist in this field~
Hallo liebes CopterTec-Team! Eure ausführliche Anleitung hat maßgeblich zur Rettung unserer Drohne nach einem Salzwasserschaden beigetragen. Überraschenderweise hat's die Drohne dabei überlebt ( ua-cam.com/video/dZ6xFxjxqY8/v-deo.html ). Danke euch auf alle Fälle! Liebe Grüße aus Österreich, Doris & Matthias
Hallo ihr beiden. Das freut uns zu hören. Wenn noch Fragen bestehen einfach melden. Ansonsten gerne bei Facebook oder Google Bewerten. Danke. goo.gl/rpF5fm
@@thilinarajapaksha275 Ok just search for Mavic Air IMU on ebay... but check out that you buy a good one. Many ebay items are in a bad condition. Greetings to Sri Lanka. I was there 2017 ;-).
Hallo, ich lebe in Argentinien und schaue mir deine Videos an. Ich finde sie exzellent und es zeigt, dass du ein Elektroniker oder ähnliches bist. Ich möchte Ihnen zu diesem interessanten Video gratulieren und Ihnen meine Grüße senden.
Javier Medina cómo estás? Que problema tuviste? Yo tengo constantes errores de compás. No logro calibrarlo. Sabes algo de desmagnetizar el compás y donde se ubica?
Super Video - vielen Dank. 👍 Bin gerade am überlegen ob ich meine Drohne repariere oder einschicke. Sie ist gestern bei der Landung plötzlich nach links abgezogen... direkt ins Wasser. Hab sofort Akku entfernt und für über 24 Stunden getrocknet. Zwar waren es „nur“ ca 15 Sekunden in 30 cm tiefen Wasser, aber sie hat nun kleinere Macken: der gimbal scheint nun zu spinnen und im hinteren rechten Sensor hat sich Wasserbelag von innen gebildet, außerdem knirschen nun die vorderen Arme. Scheinbar ist beim Aufprall Sand aufgewirbelt worden. Bei der nächsten Drohne wurde definitiv DJI care gebucht 😞 geflogen bin ich bisher auch noch nicht...
Sehr gerne :-). Notfalls einfach einsenden. Jetzt ganz wichtig: Erstmal mindestens fünf Tage in Reis legen und nicht nochmal einschalten. Das Wasser muss komplett raus. Danach testen und uns gegeben falls anschreiben.
Wonderful job! Great info video even without understanding German Image speaks for itself. With your video I could remove and replace a leg from my Mavic Air. Thank you!
CopterTec by the way I bought another Mavic Air that got in side of water, my ideia is to fix it as well. After I dry it I turn it on. I notice that just the camera gimbal is moving to the left and right nonstop and the front red lights are on. Do you have any ideia if I need to buy some of its board ? Thank you very muck
CopterTec thank you very much, yes I guess its the core board. On the other mavic air I increased the wire for replacing the left back leg without open the drone but the wire became kind of long and after trying to put it inside the drone both back legs stoped. Now I open and replaced the left leg soldering at the board but both legs still not working. Do you think I did demage the power board? On the DJI App it says 3No.Esc Error and 4No. ESC Error. Thank you so much.
I want to say thanks a lot for this video. I managed to strip down my mavic air to replace the rear left leg and now I'm up flying again! Can't believe I did it! Cheers!!
Haha great you hear. You are welcome :-)
Hi guys, I want to replace the right front and rear arms on a mavic air myself. Where do I get them? Thanks if you can help.
Douglas Ferraz Hiya. As you've read from this video I have bought, replaced and fixed my mavic air using this great video. I can only say that I bought my replacement leg on eBay but I've tried to find something similar for your needs. Unfortunately I can't see anything now but maybe you can. It cost me roughly £80 with customs cost etc for just the the rear leg! Good luck
QUAD FLY thanks brother. I am in the USA, I looked online the options were from aliexpress and Ebay. I am scared of those been fake and not work correctly. That is why I wanted to buy from the same place as someone who already had positive results. Since you bought your from Ebay I am assuming it's a 3rd party part not original and it works fine. Right?
Douglas Ferraz fixacrash.com/ bought mine from here I discovered. Hope you can get sorted. Watch strip down video carefully and mind the fact you have to solder two wires of new leg.
Für mich der Hammer was hier gezeigt wird ! Hier wird eine wahnsinnige Arbeit dargestellt als wäre es Nichts, Respekt !!
Hi, das du dieses Video gefunden hast :-).
Phantastisch! Bildqualität, Kommentare, Know-How - alles gerade richtig, nicht zu viel und nicht zu wenig. Eins der besten Teardown Videos das ich kenne.
Vielen Danke für die freundlichen Worte :-)
I came to this video after crashing my Mavic Air and breaking the left rear motor arm. Although I speak English I was able to follow the video.
Your descriptions with pointing out components made it possible to follow.
By far the best video on You Tube for the Mavic Air. Well done. Hope to see an English version real soon
Hi, yeah english subtitles would be nice... But at the moment the time is a big problem.
Ihrer Erklärungsvideo ist ausgezeichnet. Vielen dank. Ich habe ein bisschen Deutsch gelernt! 本当にありがとうございます。Really: thank you very much.
したいです。 ;-)
I speak no German however I repaired my Mavic from this wonderfully informative video by following the teardown until I found the problem Great stuff thanks :) was a life saver :) :)
Hey great to hear... Have a nice day and enjoy your flights.
Mein Nachbar hatte seine Dji Mavic Air geschrottet . Super erklärt, hast mir dadurch sehr geholfen . Danke 😉👍
Super das freut uns. Viel Spaß beim fliegen.
Vielen dank, für die Klare problemlösung. Hab die IMU bei AliExpress gekauft für €18. Mit deinem hilfe via You Tube, selbst die IMU ersatzt. Super einfach, und die Mavic Air ist problemlos wieder in die Luft ! Danke!!
Sehr gerne und viel Spaß beim fliegen ;-).
Chapeau!Inhaltlich super gemacht, kurz und prägnant gut erklärt. Bin begeistert!
Vielen Dank das freut uns.
I don't speak German but i'm a visual learner anyway. This is a great in depth break down video. Danke mein Freund.
Bitteschön :-) Greetings
What type of screw is used to hold the top cover?
Hi, seems like standard 1.5mm screws. There is a screw kit on the market. You can sell it directly at coptertec.de.
Very clear and helpful video. Translating from German adds to the fun :) But you can clearly see how to dismantle to replace parts.
Great feedback. Thank you :-).
You saved my day! THANKS!!!
Great. Have a nice day :-).
Tolles und sehr interessantes Video. Man sieht dass da bei dir viel Erfahrung, Wissen und Feinmotorik dahinter steckt. Ich fand es sehr spannend!
Dankeschön das freut mich. Schöne Grüße
My Mavic Air is Not Turnning On Please Help Me Out
Hi, please write us an email with your problem. Your battery is on or off? Please press the battery button short and then long.
@@CopterTec yess I used For sevral months but Its not Starting dnt whats exact problem
@@rutviktambe Can you tray another battery?
Sehr gut erklärt danke für die Zeit und Aufklärung 👍
Sehr informatives Video 👌 Hat quasi alle meine Fragen in einem Video gelöst
Super freut uns :-)
Very interesting video ! Could you add English subtitles or commentary for non German speaker? :)
Hi, yeah thats a good idea... I hope my bad english is good enough :-)
CopterTec crashed mine at weekend and def need a help here, in English!
Hey, how I can help you?
CopterTec crashed mavic air into a tree (sideways!) and snapped the rear left leg off at joint. Wire hanging in there but must be disconnected a bit because I'm getting an rcs error. I've ordered a spare leg and hope to fix myself. Have you got any recommendations? Cheers
Ok the error sounds bad. In some cases the ESC board is broken after a crash. Best way: First fix the leg and give it a try.
Vielen Dank für das Video, ich musste den Motorarm vorne links austauschen. Nach Reparatur startet die Drone und fliegt, allerdings Steuerung nach vorne und nach hinten nicht möglich, alle anderen Richtungen (seitlich, hoch und runter, Achsendrehung) in Ordnung. Woran kann es liegen? Danke für die Hilfe.
Hallo, das freut uns zu hören. Klingt als würden Sie in einem kleinen Raum versuchen zu fliegen. Dann blockiert das Vision System diese Manöver. Am besten eine große freie Wiese suchen, damit nicht der nächste Arm kaputt geht :-).
Thank you!!! Broke a rear arm axis after an unfortunate loss of signal timed out under a tree. Was actually impressed at the self inflicted beating the drone repeatedly took trying to RTH before crashing to the ground. Was able to follow along quite well without language comprehension.
Hi, thanks for your nice feedback.
Das war einfach super!!!! Ich gratuliere!!! Schöne Grüsse aus Brazielien!!!
Freut mich. Schöne Grüße zurück. Have a nice weekend :-).
Danke, wieder was dazu gelernt !
Freut uns. Viel Spaß beim Fliegen :-)
I don’t speak German but this was done so good I didn’t need to understand the language👍
Thank you very much for this nice words 🤗
Amazing video, thanks. What adhesives are needed for reassembly besides the white PU glue? What, if anything, was used on the cable plugs and fan motor? Are any other supplies needed for reassembly?
Thanks for your nice feedback. You only need the white PU glue. The fan can be assembled with the same glue. Also the silver protector stripes above the plugs.
can you me why doesn't connect remote and no wi-fi signal
Hi, sounds like a demaged core board... water demage?
謝謝你的影片,教我修理好了我的Magic air。Thank you for your video ,taught me to fix my Magic air。
You are welcome. Enjoy your flights.
Amazing video, I had another problem the drone LEDs are blinking red, yellow, green (self-diagnosis) and I can not connect to DJI Go or DJI Assistant. I also can not press the back button to connect with WiFi.
Hi sounds like a damaged core board... 😞
@@CopterTec The only thing I can think is that I turned on the remote id two days before and the (self-diagnoses) continue to run at the start-up. (green yellow red).
@@Univers314 Hi sounds more that you damaged your core board 😞
Super great video. It's understandable even in Germain! Very clear and illustrative. One question though: Which part is usually unusable when when fallen in fresh French water?
Haha thanks for your nice feedback. Sometimes everythings is unusable. But often the ESC Board is demaged and nothing else.
I intend to tear it down completely to be sure, to be sure...
@@Souvorof Yeah and clean it with alcohol.
Hallo.Ich bin Slowake und kann kein gutes Deutsch. Ich hatte einen Unfall mit mavic air.Kamera ist in Ordnung. Video-Uploads! aber der Gimbale-Motor funktioniert nicht.Kardan muss nach dem Austausch installiert werden?
Can the WiFi chip be ungraded..??
No seems that there is no solution. But you can use the "FCC hack" to extend your range.
hi. der weiße Kleber an den Lötstellen für den Motor dient zu Zugentlastung nehme ich an? Was ist das für ein Kleber, fühlt sich wie Silicon an. Bin gerade dabei den Motorarm hinten links zu wechseln und würde die Kabel gerne mit gleichem bzw. ähnlichen Kleber ankleben. Könnt ihr mir verraten was das für Klebstoff ist? Vielen Dank
Hallo, wir verwenden "Plasti Dip" für die Lötstellen.
thanks to this video I was able to restore my mavic air that went for a swim and was able to fly out of the lake XD we´ll see how long it lasts and if there were any long- or short- term effects in the overall performance. THANKS for sharing this content
Hi, you are welcome. We recommend a total clean with alcohol (isopropanol). So the oxidation process is stopping. Greetings
How do I replace front sensor...??
Hi, just remove the two screws at the front (on top of the vision system). Then you can remove the front vision system.
If I’m just swapping out the IMU do I need to take off the fan, GPS, etc..?
Only the fan because you need to remove the Core Board and disassemble all cables (under the fan).
CopterTec awesome! Thanks
@@grantburke3523 Welcome.
Top video, hat mir sehr geholfen beim Tausch zweier Arme.
Schade das du den Arm nicht gezeigt hast mit der Antenne, da war ich kurz Ratlos.
Wenn die Drohne keine Fehler mehr anzeigt, kann man sie Problemlos starten ? nach dem Kalibrieren natürlich
Hallo, das freut mich. Ja die Antenne wird ja oben beim zerlegen entfernt :-). Beim Mavic 2 sind wird gründlicher ;-).
Wenn kein Fehler mehr da ist kann es los gehen. Wir machen aus Sicherheit immer folgendes:
- Firmware Update
- Gimbal kalibrieren
- Vision System kalibrieren (via DJI Assistant 2)
- Kompass kalibrieren
@@CopterTec okay super, erste Schwebezug in der Wohnung lief ohne Probleme.
Ich hab leider nur die Air und weiß nicht ob der aufbau bei anderen Modellen wesentlich abweicht, aber trotzdem 1A erklärt. Das hat mir einiges an Geld erspart denke ich
@@CinemaTicker Super. Dann viel Spaß beim fliegen. Und alles ganz lassen :-).
Cant understand your words, but visually you helped out a lot, danka!
Haha great, you are welcome. Bitte :-).
I am removed imu an cleaning after Ree fixing, but not solved the men control data err and imu error...😭😭😭😭
Oh thats bad
Hey! Great video, except the fact that i dont understand german ..
What is the name of the cable you point at, at 11:00, right after you point at the camera cable?
My camera is working, but I cant move it with my controller anymore, and its not stabilizing. I seem to have damaged that said cable when I had to change my rear arm.
Thank you and sorry for the german... Look for "mavic air camera flat cable". But hard to find. We have still some in stock. Greetings
@@CopterTec No worries, you're a German company so^^. Ah yes, I havent been able to find one online that looks the same as the one I have. My camera wont move or calibrate, so I guess the cable must be damaged. You dont happen to ship to Norway by any chance?
@@Dernel2 Norway is no problem. Are you sure that the problem occurs from this cable and not the silver one? Is there a video link and can you enter the video settings?
@@CopterTec I'm not 100% sure. Video link is working, and video settings and camera settings are adjustable. The gimbal calibration always fails at 10%. Its possible that I damages that cable when i changed one of the arms. When I google "mavic air flat cable" I cant find any cable that looks like original.
@@Dernel2 Ok that can also happen if your signal wire (silver one) is demaged. I'm not sure if you can buy this cable in any consumer shop. We got this product directly from DJI.
ich frage mich ob es mögllich ist zb einen Sensor eines alten Pixel 2XL in die Mavic Mini zu pflanzen ^^
Hallo, den Kamerasensor oder einen anderen Sensor (Gyro, Kompass, usw.)? Ich denke ersteres dürfte nahezu unmöglich sein (das zweite sehr schwer wenn nicht identisch). Es muss ja nicht nur das Maß sondern auch die Belegung der Pins identisch sein. Desweiteren muss die Ansteuerung der Software stimmen, sonst gibt es nur eine Fehlermeldung...
@@CopterTec
Joa fehlten iwi etwas offenes was man customizen kann. ZB ein austauschbarer Gimbal mit Kamera. Hat natürlich keiner der Großen Player Interesse daran. Die Kamera der Mini ist zB grottig gegen das was zB im iPhone oder Pixel4 verbaut wird, bei gleichen Maßen. Technisch wäre selbst eine 4k 60p Drone mit unter 250g machbar.
@@Krautmaster86 Machbar ist vieles, aber die Frage ist, ob DJI das auch möchte ;-). Leider ist das ganze so aufeinander abgestimmt, dass ein Austausch schwierig seien dürfte.
Thank you. Your video very helping me, i have successfull to change my right arm. But now esc error. Do you know how to fix it?
By the way I’m Yusuf from Indonesia, nice to meet you
Hi, nice to meet you too. Is there any bad soldered cable on top of the ESC PCB? Possible problem: a broken ESC control board.
CopterTec or my soldered when i change right arm is not good? It is possible?
Ok. Good solder skills are very important.
Hi!
Thank you for video!
Is components covered with lacquer by you or it's DJI stock painting?
Hi, this is DJI lacquer to protect the layers.
I have problem with IMU main Data controller Error How to solve?
Cooles Video. Hab eine Frage, würde es auch über euch machen lassen:
Bin mit meiner Air langsam gegen eine Hauswand geflogen.. sie ist auf den Boden gefallen. Nun ist im einen hinteren Arm ein kleiner Luftschlitz genau an der Stelle zwischen Arm und Body. Der Arm an sich ist fest, die Rotorblätter stehen nun aber auf der Seite nun minimal näher zueinander als auf der heilen Seite. Ist das sehr bedenklich? Kann das wieder hergestellt werden und mit welcher Reparatur muss ich rechnen? Schonmal lieben Dank im Voraus. Und Abo ist raus :-)
Hallo, das klingt nicht besonders problematisch. Handelt sich wahrscheinlich um das Drehgelenk. Am besten einfach mal bei uns auf der Homepage das Formular ausfüllen. Danke.
Hello, can you tell me where the compass is physically located on the Mavic Air? Thank you
Hello, the compass is on top of the Core Board at the back right corner. It's close to the rear backward vision system connector. The compass is the square IC. Pro tip: Use a magnet to locate the compass. You will see a big deflection in the app if you are close to the IC.
@@CopterTec Hello, thank you very much for your answer.
@@eduardongc You are welcome.
@@CopterTec Hello friend, I have the same doubt with the compass in the Mavic Air 2/2S and with the Mavic 2, the compass in these models is also integrated into the main board? Thanks for your answer
@@eduardongc Hello, no there is a combination of GPS orientation and external compass.
Wo könnte ich bei euch Ersatzteile für meine dji mavic air kaufen?
Hallo, ja das können Sie. Bitte einmal über das Formular auf unserer Homepage schreiben.
Thanks for this great video, I wanted to know if you can help me? I have a mavic air and I can not calibrate the compass all the time it tells me that I must calibrate it and it always throws error
Hi, thanks for your feedback. Did you have a crash? If not, check if you're far enough away from metal.
Ganz schön gruselig. Trotz fehlendem Akku sieht das aus wie eine Vivisektion. Die "arme Drohne"!
Gut das es nicht lebt :-).
CopterTec. I ordered new arms and followed your video and wanted to know what the white stuff is on the wires? I think an anti-vibration type substance, but my problem is that its on the solder joints! Will that ruin the board if I de solder the wire points with the white stuff on them! By the way, GREAT VIDEO! I don't know German but the video was so precise that I was able to follow with very little problems! THANKS
Hi, the white stuff is PU glue like Sikaflex (or Wacker). You can remove the glue with pure alcohol. But it will not ruin the board... no fear :-). Thanks for your nice feedback. You are welcome.
Thanks for the video! My Air is up and running now! Awsome video guys!
my1948hummer Great. Have fun :-).
my1948hummer Hi guys, I want to replace the right front and rear arms on a mavic air myself. Where do I get them? Thanks if you can help. I'm in the USA. Get video by the way. I hope I get get my hands on the parts to fix it.
You can check ebay. I think it's very cheap in the USA.
Bei der Komplexität der Mavic Air. Glaubst Du an die Gerüchte, dass es im März noch einen Mavic Pro II geben wird. Oder ist die Air der diesjährige Nachfolger des Pros?
tinyentropy Das weiß ich leider auch nicht. Es könnte vielleicht etwas größeres aber auch faltbares geben (zwischen Mavic Pro und Phantom). Dafür dann aber mit einer genialen Kamera. Aber das ist nur meine Vermutung...
Avez vous 2 cache en plastique sur les vis? Impossible de les enlever, j'ai tout essayé...
Hi, sorry my French is not the best. You want to remove the glue/plastic above the screws? You can use a screwdriver. Important: The newer Mavic Air drones (sind 2018) come without these screws.
@@FabianBriese
Mon mavic date de mars 2019, ce qui veut dire que je peux enlever ma coque, il n'y a pas de vis?
@@davidbruno3023 Yeah right.
Great video, thanks!!
I'm having a very hard time reattaching the rear right arm, which was somehow pulled out. I removed the 2 screws, but it won't seat correctly, and I don't want to force it. Any advice? Thanks in advance!!!!
You are welcome :-). Do you mean two of four motor arm screws?
@@CopterTec thanks for the reply. It was the 2 screws at 25:45. Looks like there's a piece of metal inside the arm which was/is bent :/ Don't think I'm able to repair that one. DJI Care Refresh 1 out of 2 left, o well. Video was still very helpful for my next screw up.
@@adambaldwin9544 Hi, yes this is a metal part. You can buy it for round about 15usd. But you need to solder the motor cables. Good solder skills are important... Or dji care :-).
i plan on using you video to replace the gimbal unit, but i read everywhere only DJI can calibrate it afterwards. Is this correct?
Hi, some special calibration procedur is only supported by DJI. But you can click "Calibration Gimbal" (DJI Go 4 > gimbal settings).
@@CopterTec ok i will try the calibration gimbal in dji go app first, hope it works
@@ginocozijns3075 Ok great. Good luck.
@@CopterTec everything worked out. Had to keep the original camera module. Placed it inside the new gimbal. After calibrating with dji app, pitch and roll were perfect, but yaw was way off to one side. I had to manually adjust the yaw quite a bit in the gimbal advanced settings
@@ginocozijns3075 Yeah sometimes you need a "manuel adjustment". But nice that everything went well.
Hi! Can you help me about camera cable replacement? Crashed the drone, signal cable teared. Replaced it with new one, but the camera is depending on (but I don't know how) how I put it back to the gimbal is tilted more or less. Is there a special way to put it back to the gimbal? (gimbal's camera keeping part is broken a bit but it doesn't seem to effect anything and I can put back the broken part). Thanks
Hi, where you bought this cable? Most cable on the market are old, used and demaged.
@@CopterTec eBay. So is the the cable's fault?
@ Yes I think so.
@@CopterTec that's not good news. Thanks for the help. By the way that's what I bought: www.ebay.com/itm/253810742052
Is there any way to solve it or do I have to buy a full original gimbal from DJI? Only problem it's very expensive, half of the price what the drone worth now
@ I think for this price its not in a perfect condition. Please write me an e-mail. I will check what we can do.
Hi
Ich hab dank euren Video den gimbal gewechselt da er abgebrochen war. Jetzt kann ich ihn nicht kalibrieren. Muss man da was beachten?
Hallo, woher haben Sie das Gimbal bezogen? Leider sind 95% der angeboten Gimbal auf den bekannten Shopping Platformen nicht funktionstüchtig bzw. defekt. Existiert das alte Gimbal noch? Am besten einmal über unser Formular eine Anfrage stellen: www.coptertec.de/produkte/dji-innovations/
@@CopterTec ich glaube das war aus den USA. Das alte ist noch vorhanden. Es war auch noch ein Siegel drauf und es bewegt sich auch nach unten und oben aber dann kippt es nach links. Auf die Kamera kann ich auch zugreifen.
Habe mal was gehört das man es mit einer speziellen Software von dji kalibrieren muss.
Ich werde aber trotzdem mal das Formular ausfüllen.
Danke
@@JustfourPrint Die mit den silbernen oder goldenen Aufklebern (glänzend) funktionieren ganz sicher nicht. Das kommt von einigen asiatischen Lieferanten, welche zur "Beruhigung" der Kunden diesen Siegel aufkleben. Das wäre ungefähr so, als würde man den Prüfsiegel auf das KFZ Kennzeichen kleben, ohne vorher das Fahrzeug zu begutachten.
At 32:36 You point to some thing on the undercarriage next to the downward sensors with your tweezers what is that? mine has a hairline crack wondering if you can replace just that little piece or if I should replace the whole body?
Hi, this is the downward vision system. You need to replace the whole system.
@@CopterTec thank you for your reply what do you mean by the whole system the electronics to or just the plastic body?
Ah you only need the plastic part? This is a part of the lower frame.
@@CopterTec yea my Magic air still woorks but it has a hairline crack the peace that the guy points to in the video that I described in my first post is it possible just to replace that little piece? or do I need to buy a whole new shell?
Yeah you need to buy the whole part. Or you fix it with glue.
my mavic air crash , i havve quation.
if my camera is normal but my gimbo it broken
can i change only gimbo and use old camera or not ?
thnx
Hi, yes you can use the old camera. Sometimes it's possible that you need to change the camera cable.
Hi. I have a one question 26:46 that parts available or not?
can i buy this parts ?
@@rabirokka6624 Hi, yes this part is in stock. Write us here: www.coptertec.de/produkte/dji-innovations/
Hi CopterTec, very nice and detailed video. I crashed my Mavic air into sea water and now it displays ESC Error, Battery Signal Error and the gimbal camera does not rotate. it was there in water for about 10 secs. Do u suggest i send back drone to dji or it can be repaired by myself. The drone is just 2 weeks old.
Hi, thanks for your feedback. Ok I have very bad news for you: sea water is a good electrical conductor. So I think your mavic is dead... Sry.
Thank you for your prompt response :) I guess i'll have to get another one and learn from mistakes.
Hey. You are welcome. And enjoy your flights with the new one.
Fantastisch 👍🏽
Danke.
Yes, but did it fly after you put it back together? I've I had done that it wouldn't have!
Haha yeah it's flying, why not ;-)... you can watch the timelaps of assembling at the end.
CopterTec Oh, I saw the end. I just didn’t see it turned on. 😜 I wonder how many people will want to change out the color panels, like from white to red. I saw you broke at least one tab taking the top cover. What we’re in the bags at the beginning of the video? My German is a little rusty.
Haha yes next video I will turn it on :-). Yeah one part broke on the cover. The problem: I opened the cover for round about 10 times. So the material is a bit exhausted. This is the normal combo without any extras. Only the mavic air with one battery, 8 propellers in total, charger, usb c cable and propeller cage.
hi, am trying to open the top cover, but what screw driver will i use in removing the screws in the gimbal its not flat nor cross screwdriver. it looks like aa little metal ball not a screw
Hi, you need to remove the glue on top the of screws first. Then you can remove the screws with a normal phillips screwdriver.
Your video helped a lot! Thanks
You are welcome :-)
how do you take out the foot so easily at 33:19?
Hi, good question... Sometimes it's easy and sometimes it's a bit harder...
Super Video, damit konnte ich alles notwendige freilegen, um meine gebrochene Drehachse hinten auszutauschen. Am Loslöten der Rotorkabel habe ich mir etwas schwer getan, am besten man nimmt eine dickere Spitze bei 450 Grad und hält kurz drauf.
Freut mich das alles geklappt hat. Ich empfehle mit 380°C zu löten. Aber es kommt auch immer ganz stark auf die Lötstation und den Lötkolben an.
I love teardowns!
Haha yeah.
Wow. what a beautiful video.
Thank you.
ich finds top und perfekt erklärt DAUMEN HOCH und dein oszi find ich ja hammer :D kannst du mir evtl sagen was des für eins is?
Dankeschön :-). Das Oszi ist schon etwas älter aber immer noch top. Der Name von dem Teil lautet DSO Quad und kommt von der Firma Seeed. Mittlerweile gibt es (glaube ich) auch einen Nachfolger davon. Noch interessanter finde ich allerdings das LabNation SmartScope für PC/Smartphone. Grüße
Vielen Dank für das tolle Video. Jetzt konnte ich endlich das Linsenglas selber auswechseln ohne dass ich eine neue Kamera kaufen musste ;-) Ich bin gespannt ob sie wieder funktioniert wenn ich sie einschalte ;-)
Sehr gerne. Haben Sie das gesamte Gimbal getauscht? Dann muss dies noch kalibriert werden...
@@CopterTec Neun lediglich die eingepresste Vorsatzlinse.
@@romanschaller2816 Ok dann sollte es keine Probleme geben.
Hi. Could you help me to replace GPS module in Mavic Air?
Hi, yeah. How I can help you?
@@CopterTec May be you can advise me what to do. After my drone fell down it can find only 6-8 satellites and never more. I did all available calibration for compass, IMU etc. All indicators work well, no error messages BUT when I'm trying to fly it can't find more than 8 satellites even far from the town or in the forest. I've tried it in different countries and everywhere I faced this issue. Moreover, sometimes it can fly by itself to the left or straight. How do you think is it a problem of GPS module? Because it finds satellites but in the place where another drone finds 16 my drone finds only 6. Please help :)
@@SlidVibe Hi, sounds like your GPS only work with GPS or GLONASS. GPS > US system / GLONASS > rusian system. Normaly the GPS module find both systems and so you have 16 satelites. My first idea: call the DJI support and ask them (warrenty case).
I'd never thought that the interior of a drone such as Mavic Air is so complicated~ funny vid but hard to demolish it for an ordinary person just not specialist in this field~
Haha yeah this drone is full of electronic stuff :-).
Hallo liebes CopterTec-Team! Eure ausführliche Anleitung hat maßgeblich zur Rettung unserer Drohne nach einem Salzwasserschaden beigetragen. Überraschenderweise hat's die Drohne dabei überlebt ( ua-cam.com/video/dZ6xFxjxqY8/v-deo.html ). Danke euch auf alle Fälle! Liebe Grüße aus Österreich, Doris & Matthias
Hallo ihr beiden. Das freut uns zu hören. Wenn noch Fragen bestehen einfach melden. Ansonsten gerne bei Facebook oder Google Bewerten. Danke. goo.gl/rpF5fm
Broo my DJI Mavic air drone main controller data errors imu calibration fail..what I dooo?
Hi, seems that your IMU is demaged. You can write as an repair request if you want.
Broo please gevin me imu unit bye link....I am Sri Lanka.how to imu repair brooo? Please tutorial link send meee
@@thilinarajapaksha275 Ok just search for Mavic Air IMU on ebay... but check out that you buy a good one. Many ebay items are in a bad condition. Greetings to Sri Lanka. I was there 2017 ;-).
@@CopterTec but broo I am searching for eBay ..1 items only visible..and very hi price brooo...my old item you know to relayed?
@@thilinarajapaksha275 No sry... and I'm not your bro ;-)
Hallo, ich lebe in Argentinien und schaue mir deine Videos an. Ich finde sie exzellent und es zeigt, dass du ein Elektroniker oder ähnliches bist. Ich möchte Ihnen zu diesem interessanten Video gratulieren und Ihnen meine Grüße senden.
Vielen Dank für die netten Worte und schöne Grüße aus dem (heute ausnahmsweise mal sonnigem) Rheinland :-)
Javier Medina cómo estás? Que problema tuviste? Yo tengo constantes errores de compás. No logro calibrarlo. Sabes algo de desmagnetizar el compás y donde se ubica?
Super Video - vielen Dank. 👍 Bin gerade am überlegen ob ich meine Drohne repariere oder einschicke. Sie ist gestern bei der Landung plötzlich nach links abgezogen... direkt ins Wasser. Hab sofort Akku entfernt und für über 24 Stunden getrocknet. Zwar waren es „nur“ ca 15 Sekunden in 30 cm tiefen Wasser, aber sie hat nun kleinere Macken:
der gimbal scheint nun zu spinnen und im hinteren rechten Sensor hat sich Wasserbelag von innen gebildet, außerdem knirschen nun die vorderen Arme. Scheinbar ist beim Aufprall Sand aufgewirbelt worden. Bei der nächsten Drohne wurde definitiv DJI care gebucht 😞 geflogen bin ich bisher auch noch nicht...
Sehr gerne :-). Notfalls einfach einsenden. Jetzt ganz wichtig: Erstmal mindestens fünf Tage in Reis legen und nicht nochmal einschalten. Das Wasser muss komplett raus. Danach testen und uns gegeben falls anschreiben.
watched it, even though I only speak English. Wish there was an english version for those of us who broke DJI Mavic Air Arms and motors.
Hey, ask me your questions. :-)
Excellent ...!!! 👍🏻👊🏻
Thank you.
Awesome vid! Was able to fix the rear leg. Abonniert, danke!!!
Your are welcome. Enjoy your flights :-).
CopterTec
I need help looking for spare parts for dpi air. can you help me?
Yeah we received some spare parts and the rest will follow soon. Contact us via email. Greetings
Help a lot ! Very grateful !
Thank you :-)
You should of turned it on at the end ;)
Haha yeah... but was running fine. Why not.
Thank you
You are welcome :-)
Uns Zach speaking German? We need a English version
Yeah I know...
i learn a valuable lesson here! never take it apart!!!!
Haha yeah :-).
Wonderful job! Great info video even without understanding German Image speaks for itself. With your video I could remove and replace a leg from my Mavic Air. Thank you!
Hi, thanks for your nice feedback. Enjoy your flights.
CopterTec by the way I bought another Mavic Air that got in side of water, my ideia is to fix it as well. After I dry it I turn it on. I notice that just the camera gimbal is moving to the left and right nonstop and the front red lights are on.
Do you have any ideia if I need to buy some of its board ? Thank you very muck
Ok, please check the connection to your transmitter. Successful = very good (ask again) / no connection = the core board is broken (more is possible).
CopterTec thank you very much, yes I guess its the core board.
On the other mavic air I increased the wire for replacing the left back leg without open the drone but the wire became kind of long and after trying to put it inside the drone both back legs stoped. Now I open and replaced the left leg soldering at the board but both legs still not working. Do you think I did demage the power board? On the DJI App it says 3No.Esc Error and 4No. ESC Error.
Thank you so much.
Oh sounds bad. Two possible options: motors / soldering damaged or the ESC (power) board is broken. Greetings
Merci!
You are welcome :-)
Je vend mon Mavic air 1 problème caméra
Guter Mann...!
:-)
Pest & Cholera Danke
VERY GOOD...
my mavic air fall dawn & shows main controller data error & it says unplug cable between aircraft & dumping plate .what should the problem
Hi, sounds like a broken cable between the two circuit boards. Or the board is broken...
just WOOW...
Thank you :-)
und jetzt schön eine neue verkleidung kaufen und wieder zusammen bauen
Nö, der Mavic dient als Ersatzteillager. Wir haben hier schon drei Defekte Mavic Air bekommen.
richtig krasser tech-porn-shit! - chapeau!!!
R Schmid haha so kann man das auch sehen ;)
Yo, bi```! :)) Die Skills haben wirklich was neurochirurgisches: Knowledge & filigranes Handwerk.
R Schmid Freut mich :-). Mein Glück sind die kompakten Finger... Aber von Patienten die Antworten können lasse ich die Hände ;)
Very good but I don't understand German.🤔🤗
Porto4ever Filipe yeah sry. I need some free time for English subtitles.
Cool now I know how to remove the top ' so I can change colors 😁
steve scarberry haha yeah... Rainbow Mavic Air :-)
How did you guys remove the top I'm having trouble
Hi, just with a normal head screwdriver.
Shame it's spoken in Gibberish...🙄
No, just german... :-)
plz make it English
Yeah I know... but to busy at the moment sry.
Please give me your mavic air
Hi, what do you mean? The Mavic from the video?
@@CopterTec I would love to have a mavic, but not enough funds to keep it😭
@@iwayansutisna9933 Ah yeah... very expensive.
@@CopterTec yea
I like very much your videos and your technic, I subscribe your channel and please translate your language.
😉👌👍👍
Hi thank you. Just no time at the moment... translation will comming soon (hope so).
Give me mavic air drone please,😂😂😂😂😂😂😂😂😂😂😂😂
Me too, please :-)
partacz
Please no hate comments. Thanks
Un français
Oh you can translate if you want :-)
Schnitzel.
Lecker.