Good afternoon D3P. I always follow your channel here in Brazil and a few months ago I had the opportunity to clarify a doubt with you about this DDCS V3.1 controller. But recently there was an abnormality during the cutting process with the controller, where the Y axis at each complete turn it shifts a little away from the initial positioning causing an inaccuracy of the cut. Has this ever happened to your machine? Do you have any idea what it could be? Thank you for your attention and I hope I can be of some help.
Hello Edmar. Thank you for watching. I have never seen that on my machine. Maybe it is a parameter in your cnc software and not the DDCS . In the DDCS check the Parameter #113 is set to 0 I hope it helps :)
@@weitlingD3P Good morning D3P. Thank you for your support and prompt service. I'll try to change the parameter to try to fix this. Since it was using another controller and this did not happen, the suspicion falls on the DDCS. Thank you very much.
Super właśnie kupiłem ddcs v3.1 i twoje filmiki tłumaczą podstawowe setupy , dziękuję bardzo . Ja dobrze widzę że jest tylko jeden kabel do tego proba? jak to zbudowałeś? normalnie potrzeba chyba 2 kabelki z kleszczykami na frez żeby zamknęło obieg .
@@weitlingD3P bonjour je me suis mal expliquer je fait mais dessin avec fusion 360 puis je fais une simulation pour voire le trajet d outils et puis on dois choisire un g code compatible avec le contrôleur exemple dans la liste grbl ou Mach 3 ou fanuc etc.... voilà j'espère m'avoir bien expliqué
@@Levisgil47 Maybe i not understand correct. Take a look at the link below, at page 67 then item #83 #84 #85 Is it that you are looking for? drive.google.com/file/d/1987kj9OTJ87Z6NIBZqw8uX5PfoYzbJun/view?usp=sharing
![Lp. Сердце Вселенной #60 РОЖДЕНИЕ ЛОЛОЛОШКИ [Финал] • Майнкрафт](http://i.ytimg.com/vi/YoR0pAV9FVQ/mqdefault.jpg)
Thank you for sharing your knowledge with us 🙏.
Amazing content ❤. I am learning a lot from your videos 😊.
Fantastic video! Thanks for sharing this, extremely helpful! Paul from Australia here 👍
Dobra robota , przyjacielu .
Fajny film z poradami nagrałeś .
Pozdrawiam z Pruszków, Poland
Dzięki Pozdrowienia. Cieszę się że ci się podoba.
very creative, great video...thx
Takker for en opplysende video. Hilsener fra naboen i nord.
Very nice video. Congratulations
Все элементарно и просто ! Спасибо!
You are welcome
Thank you very much for this video
You are welcome
Thanks
Thank you. very useful!
Great video! How do you wire both floating probe and fixed probe? did you have to split the probe input?
The video is great for user.
What did you press to get to the probe limit switch test screen ?
If I remember correct you push the Page R button 3 time
Can you do tool offsets?
Hi and thanks for watching. No. The ofset parameter are there, but does not work
Good afternoon D3P. I always follow your channel here in Brazil and a few months ago I had the opportunity to clarify a doubt with you about this DDCS V3.1 controller. But recently there was an abnormality during the cutting process with the controller, where the Y axis at each complete turn it shifts a little away from the initial positioning causing an inaccuracy of the cut. Has this ever happened to your machine? Do you have any idea what it could be? Thank you for your attention and I hope I can be of some help.
Hello Edmar. Thank you for watching. I have never seen that on my machine. Maybe it is a parameter in your cnc software and not the DDCS . In the DDCS check the Parameter #113 is set to 0 I hope it helps :)
@@weitlingD3P Good morning D3P. Thank you for your support and prompt service. I'll try to change the parameter to try to fix this. Since it was using another controller and this did not happen, the suspicion falls on the DDCS. Thank you very much.
Why did you use copper?
at was what I had available
Super właśnie kupiłem ddcs v3.1 i twoje filmiki tłumaczą podstawowe setupy , dziękuję bardzo . Ja dobrze widzę że jest tylko jeden kabel do tego proba? jak to zbudowałeś? normalnie potrzeba chyba 2 kabelki z kleszczykami na frez żeby zamknęło obieg .
Dzięki za oglądanie. To bardzo dobry kontroler. Masz rację co do 2 przewodów. 1 przewód jest na stałe w kontakcie z wrzecionem
@@weitlingD3P fajnie naprawdę duża pomoc , dzięki wielkie
I dont understand where does the cutter has a +24v or -24 wich contacts with that probe |?
Hi The probe does not use Volt. It is a analog signal from a switch that is open or closed.
@@weitlingD3P so cuter is just grounded spindle signal thats it ? I mean the cutter part not the probe part.
@@povilasvaiciulis7931 Yes that is correct
Bonjour quelle g code et compatible avec se contrôleur
Bonjour. Tous les codes G sont répertoriés à la page 72 du manuel. sVoir le lien vers le manuel.
nvcnc.net/pdf/NVCNC_DDCSV3.1_EN.pdf
@@weitlingD3P bonjour je me suis mal expliquer je fait mais dessin avec fusion 360 puis je fais une simulation pour voire le trajet d outils et puis on dois choisire un g code compatible avec le contrôleur exemple dans la liste grbl ou Mach 3 ou fanuc etc.... voilà j'espère m'avoir bien expliqué
@@jean-pierrepetit3229 Rebonjour. Je n'utilise pas fusion 360 donc malheureusement je ne peux pas t'aider
Je voulais juste savoir le non du g code que vous utilisez pour votre controleur
Good job!!!
Hello, Does the DDCS V3.1 takes care of the backlash? Thanks
Hi Yes you can enter how many millimeters you want it move after home or limit. I use 5mm
@@weitlingD3P This is for software limit settings. Are you sure this is as well for backlash compensation settings ?
@@Levisgil47 Maybe i not understand correct. Take a look at the link below, at page 67 then item #83 #84 #85 Is it that you are looking for?
drive.google.com/file/d/1987kj9OTJ87Z6NIBZqw8uX5PfoYzbJun/view?usp=sharing
Try this link drive.google.com/file/d/1987kj9OTJ87Z6NIBZqw8uX5PfoYzbJun/view?usp=sharing
Found what you where asking for Yes it has Backlash see picture 1drv.ms/u/s!AgaOae17V8HihJYDLuP03kunSzy0yw?e=eiYJc5
'll better when You start rotating spindle, cause tool isn't cylinder