HOW TO? WLTOYS 124019 Mod 1 Gear Conversion
Вставка
- Опубліковано 17 січ 2021
- Get Your Very Own WLTOYS 124019 Here - www.banggood.com/custlink/KGG... This Wltoys 124019 upgrade to Mod 1 gearing is fairly easy and around 10-15 mins work. Hope You Like It Share if you do. Buy The Best ESC & Motor Extension Leads Right here - www.ebay.com/itm/153961222007
Like It? SHARE, SUBSCRIBE & HIT THE BELL - ua-cam.com/users/Driftomaniac...
RC Car Products We Use:
PowerHobby RC Car Speed Meter (Worlds Best!) - tinyurl.com/RCarGPS
Powerhobby Batteries - tinyurl.com/PowerHobbyBatteries
Gensace Batteries - genstattu.ositracker.com/1931...
Batteries For Bashing - www.banggood.com/custlink/m3D...
25KG Servo - www.banggood.com/custlink/vGv...
1/5 Scale Servo - www.banggood.com/custlink/m3D...
Cheap RC Radio We Use The Most - www.banggood.com/custlink/mD3...
Best RC cars Under $100
1. WLToys 144001 (40mph!) - www.banggood.com/custlink/vmm...
2. WLToys 124019 (43mph+) - www.banggood.com/custlink/KGG...
3. Q902 - www.banggood.com/custlink/Dvv...
4. SG1603 - bit.ly/3qlZpc3
5. HobbyPlus CR24 G-Armor - bit.ly/3rws4Nt
Best RC Crawlers Under $200: -
1.) RGT136161 - www.banggood.com/custlink/3KD...
2.) Redcat Everest 10 - bit.ly/36ng2xr
Want to send something to Driftomaniacs to review and see it on the channel? Contact us via the link on the 'about us' page
#RCCARS #WLTOYS #124019
It would prevent you moving the motor again without some work but you can buy little heatpipes. If you thermal epoxy them between the motor and the chassis to improve the heat transfer, I think it would be a super effective heatsink, especially on damp ground.
Fraser thanks for that tip! That's the kind of value add post we love!
What mod1 spur and pinion gear you use ? How many tooth for spur and pinion gear ratio ?
Me and my boys waiting for our ordered 124018's.... The suspense is killing us! ( Nice uploads on these models dude )
I just finished my conversion on a 124019. I went with m0.8/32p gearing. I chose a traxxas 32p 34t pinion made for the UDR as my spur (TRA 5639) and a 21t pinion gear (TRA 3951). Im running a 6.5t sensored motor with a Quicrun 10BL120 esc. For the servo I chose a Savox Sw-0250. For the motor mount im using an adjustable mesh part from rcawd, I had to file quite a bit of material from the motor mount to get the spur gear clearance. I was able to keep the stock esc location, center chassis brace and the stock body with only a little bit of trimming to the brace and body. Running contact foam tires and a tired old 2200mah 2S I achieved 68mph. I suspect with a strong 3S 100mph will be possible. The car is very smooth and very stable at speed.
excellent job sir... I may be getting this car in the future and videos by rc car experts are priceless...thanks
Uncle Rich giving the best conversion advice in all of UA-cam. This man knows his shit.
Thank you for showing the work involved love your channel
Appreciate your educational videos... I need them
Appreciate this vid.. I went a few steps ahead of u and ran into all the problems! 🤣😂
Great video Rich👍
Say it slowly "Don't forget to hit the bell 🛎"
Hi, Nnce to see how enthusiastically you are doing this.
What I always do, and certainly for things that should not come loose, is e.g. the adjustment screw / locking screw in the sprocket wheel of the drive shaft ... drill a small point / hole where the adjustment screw / locking screw is fixed and tighten this screw incl loctite 243. Your sprocket is now 100% secured.
Nice video that will help a lot of people
Awesome videos man. Thanks to you I bought this car as my first RC. Now attempting the mod 1 gear upgrade. Could you post a link to the gears you used. I ended up getting the wrong ones twice. Please help.
Brilliant solution, Thanks for sharing 👍
Glad to be of help I am in the dark hours of Covid working on a twin motor solution and a wide body chassis
Nice one mate, that's going to be seriously quick with that new motor 😎 👍 I do my gear mod a little different now. Keeping the bearing and modifying the stock mount. The gears need to be machined to almost half the thickness to fit. By hand, very, very time consuming 😅 unless you have access to a lathe. A few guys including myself just kept braking the driveshafts on the 144001's once we done away with the centre bearing.
would it be possible just to drill new holes and move the motor mount back slightly?
Thanks so much for the tip, I have actually been debating buying a mini lathe for a while now. That said I've just got a new 3D printer and I've a thought to print out a new bearing carrier to go in the middle of the car/chassis. Does anyone sell an uprated driveshaft as if you've bust one then I'm likely to! Still hot where you are? Rain's eased up here and it's getting a little warmer
@@DriftomaniacsRC a few guys have experimented with carbon shafts but haven't offered anything for sale yet. Yeah it's still hot as hell here is Brisbane I managed to get out for a test run on the weekend but couldn't get past 145kph without it skidding out of control🤔 I could work out what it was roadside but turns out the front splitter was touching down (too much downforce) when I saw the damage under the splitter I was relieved it was just a simple problem 🤞😅
@@MatthewSimm possibly but then you need to make up for that difference on the Radio tray and bearing location 🤔
@@TheRCMaster yeah fair call dude!
Love the channel. I’m yet to use mine it come the other day been but been unwell, do you think the greasing the diff is essential before I run it guys ?
Nice job! Wish I would have seen this two days ago when I did mine. My grub screws were stripped so I had to dremel them with a slot and use a screwdriver to get them out. I like that you addressed the different motor mounts, I was wondering how I might put different gear ratios on there.
The stock motor screws seem virtually glued in, those motors are cheap (if you've not a spare 540/550 can one already) and it's just way easier to junk the whole thing! Might seem brutal but also without a dremel or a drill you've few other options if any. Hope it all helps!
What battery are you running with a 3.5t 11000kv motor? I noticed it calls for 1s, I think 8.5t is the lowest that calls for 3s. I think with my twin motor setup gearing is my best option considering I'm only running 4000kv. Testing finally starts today. It's fairly easy to make the stock mounts adjustable with a dremel tool. I cut 2 stock mounts in a way that the center screw catches both halves of the mount. I can send pics if you like.
Hey richy. Love the channel. Just done the conversion but the centre brace no longer fits. What did you do to refit or do you just leave it off?? It's a speed run car so no jumping etc...
Thanks Rich ! Gonna send my 144001 to the moon and probably to heaven as well lol
Hey Richie
Question mine 124019 arrived today everything ok! But for what is the Mode Button next to the on /off switch on the Transmitter????
Mfg Diddy
hello great video. may I ask what is the stock motor shaft? 3.175 or 5mm? plan to convert to brushless. thanks.
Nice video, any wait for part two. The motor mount is a real pain in the butt, someone should make an adjustable one, can you imagine?
guy in my mod group got 124019 to over 150. I ordered one immediately after
Hey do u know what brushless motor and esc fits in the px toys desert journey without going through the website and ordering that junk from them Nd waiting forever
Hi I just changed my front diff because of a crash and when I was putting it together I twisted it to see if it sounds ok and it was a very light crunch, so I put it together 😳 and now I don’t have 4WD, what should I do to try get it back. Also I can turn more left than right, when I turn right it hits the gearbox housing, what should I do about that ? Have I set my steering up wrong ?
So I haven't see this channel in a while . And the lighting is sooooo much better glad you got that sorted . But your mic isn't so good in the intro. The distortion kicks in at any sound it detects. But your video is very entertaining and good with information
Brand new mic, only the 7th-8th one in 18 months....I've tried $300 ones with the same results. Got two huge led backlights behind the camera, which makes a big difference. Simply can't afford another new mic as I go for top reviewed ones and same result. I'd rather spend the money on cars as I am not a sound engineer.
@@DriftomaniacsRC ah right same. I've got a £10 mic and it's alot better than my phone mic. Maybe it could be some settings on your phone
Richie please help mate ! I'm a noob just getting into rc and I have a 124017v2, I'd like to know what exactly is mod 1 gearing?
How come you had 2 different sized pinions but both of them were mod 1 ? How do I know? Can I only use those 2 size of pinion gears to make mod 1 or is there a certain method or calculation etc that will let me know what gears are mod 1?
Please help mate as I'm lost on this point.
Great video as always mate,very instructive and I'm confident I could now change the gearing I just don't know how I'd know what gears make mod1.
Many thanks for any help you can give me and best of luck with the channel 👍
Hi mate, I'm about to start a build of a 124017 with a SC8 120A with a 3650 5200kv motor!!
Have u any advice/links to preferred gearing?? ;-)
nice this i want to watch..
I know this is an older video but does anyone know what bore the gears need to be to fit on the driveshaft of this car
Can u send an Amazon link for the mod 1 gear
Rich we all wanna see you hit 120mph
Can you use a wltoys adjustable motor mount ???
can i know the size inner diameter spur mod 1 ... is not 5mm is it ?
Nice Video , Verry helpfull! Do you know if the original gearing is 48dp ? Thanks
Th original pinion/spur is 0.7 Mod which is VERY hard to find.
@@coquirc4537 thank you !!
I want to do this, what size of pinion and Spur should I purchase?
Can you give me some Amazon links to a kit that I can upgrade the parts on this car with please
But one question I'm new to this and i have the 124019. But if you put in a gear that has less teeth on it doesn't it make rotations slower and over slow the overall initial speed of the car?
It's different pitch so it would be a different ratjo I believe
What is the tooth count on the front & rear diffs. (Ring, & Pinion) also how tall are the tires?
You'd need to check the spec online
Since the gear has a grub screw and it fits over the drive shaft why no make it a mid motor? you could still put the gear anywhere on the shaft
I see what you mean but the grub screw is screwing on to the flat part of the shaft you could cut a flat spot in the middle of the shaft but it’d be a lot more work to move things around and there’s the body to consider as well
It's 5mm for mod1 spur right
Why go with Mod1 gearing which are bigger tooth then standard instead of 48 or even 64dp gears? Those should be more silent?
It's finding a gear that'll fit on the center shaft that's the main problem as opposed to the pitch. Also with serious brushless power mod 1 won't break or slip
Richie, i found the adjustable motor mount for 144001/124019!
I've got a 3d printed one and I found the adjustable one on aliexpress but it'll be a few weeks before it's here. Where did you find yours?
@@DriftomaniacsRC Found it at same place! Hopefully it works. I have a bunch of MOD 1 pinions coming in. I got the 34, 29 for Spurs and the 19, 20, 21, 22 as pinion gears. I watched a video on how to keep the bearing without needing a lathe, hopefully itll work out when i get all the parts in.
The traxxes mod 1 34t is too big! You can’t use it. Have to use 29t to fit
Link?
It says mod 0.8 on your gear?
Great video but the sound is messed up
What's up with the tiny corner video?
Does this cause more or less overheating im a noob
Depends on what gear ratio you run
I thought all aluminium heat sinks used the conducting paste?
First rc car I've owned or test driven with it on, and I've driven quite a few 😏
@@DriftomaniacsRC Fair enough but as an engineer for quite a few years i know that aluminium is very susceptible to corrosion, even more so when pressed up against another type of metal. The paste is to combat the corrosion but still transfer the heat through to the sink. You can also use a type of gasket for the same purpose. But any build up of ant kind between the surfaces ruins the heat conducting.
How long is the centre shaft
John it's 203mm, don't ask why but I have Precisely measured it!!!!
@@DriftomaniacsRC assuming the shaft is 5mm diameter itself? Just making sure it'll be a perfect fit with my mod1 gears
How good are the power hobby motor fans
very good, just finished fitting another twin setup to my felony 5 mins ago
@@DriftomaniacsRC I will see it right now
it's not a grub screw
I wish I had one, seems like I'm the only one that doesn't!
Your missing out, they are awesome, I have one of each 😁
Is it really this simple? If so, why does everybody make such a big deal about having to modify the stock spur gear when upgrading to a brushless motor? It'd be much easier to just replace both gears rather than trying to modify the stock 0.7 MOD spur gear where you're limited to only that spur & pinion. Why don't people just swap to a different spur & pinion gear instead of trying to reuse to stock 27T gear that causes cogging, etc...?
I've just gotten into these cars so maybe I'm missing something? It just seems logical to swap spur & pinion to a common size so you have options instead of being stuck to the stock spur and pinion gears.
time for an new mic
I’ve just bought this one about a month ago. 7th one and $500 over 18 months there’s not going to be an 8th....fed up of trying so called good mics.
there is no transmission
Tooth count should be around 49 or 50, not 55.
I was told 55 so that’s what I was passing on thanks for the feedback though.
@@DriftomaniacsRC
I am confused, you just installed it using a standard mount so your combo must be close to 50T? You also did the same on you my 14001?
Scott N is correct. Drifto you should make a correction.
So this basically is a 1:1 gear ratio? I've got a 2838 motor in my 144001 wouldnt that cause a lot of overheating issues
@@CallMeAdam2023
No that's not correct. Gear ratio will vary depending on your setup.