Holy crap! Just to replace a light bulb? Mental note that when negotiating car purchase with salesman they throw in lifetime free labor for bulb and battery replacement! This is an engineering joke!
To replace the low beam there’s no need to do all that hard work. Just take off the dirt protector cover and turn the bulb counterclockwise they will come off easy. I used H11 bulbs. Hope this helps.
Finally a usefull comment, I searched the entire internet what way to twist the bulb, even this video hides it
Honestly tho, it takes a whooping 9 mins to pull the cover. Not really all that time consuming. 🤷♂️
For anyone who may ask, the Fusion high beam bulb is H7, and the low beam bulb is H11. So if you plan to replace the factory bulbs with HID or LED, these are the numbers you need. They are all listed on page 258 of the Owner Manual. Go for the other bulb replacements as LEDs at the same time.
Have fun getting LEDs bulb in the high beams, I pulled it off but required some effort and my LEDs were pretty low profile on the fan.
I am so ANGRY right now (the video was super informative though, thank you). I got pulled over by the Military Police on base last night, because I had a headlight burnt out. Luckily, they let me off with a warning, and I got off thinking I would have a 10 minute job to do in the morning. But, seriously? I have to take the bumper off? Now I HAVE to go to a garage, because even if I had the jack to do it, there's a bylaw on base that forbids us from doing any work in our driveways that involves hoisting the vehicle up in ANY way. Thank you for the video, even if it made me scream. You guys did a great job and I just really needed to vent lmao
You really don't need a jack, just the front 2 body plugs and about 6 sheet metal screws for under the front side of the car. It works I just did it, now the rest is nuts, 4 top bolts and radiator cover plugs. Wish it went in the spring, fall or summer.
Some bases have DIY garages for a fee. You even could sign out the tools. This is probably a mute point now but I guess just fyi now.
The easiest way to change the fusion lights is pour 2 gallons of kerosene in engine compartment , light, and walk away
That's Ford's idea of trying to stop people to replace the bulbs by them self and go to dealer to pay more money XD... gotta milk that cow till the last drop... this is the thing that I hate the most about the car.
I couldn't agree with you more... I was told I can't even change out my tail lights to have that borderlight o.
mrN3w7 it's not just Ford doing this. GM has been doing it for at least a decade now as well as many others. It makes me sick.
You are wrong about that. Ford want to make things easier for customers.
And removing a whole bumper to replace a headlight is making it easy
Well now they are cancelling production of the fusion and focus. Hyundai, Honda, and Toyota win!
You don’t have to do what he did at 1:53. My 2014 fusion bumper came off without that step. T25 bit and 7mm socket is what my car needed. This video was a life saver.
One of my lights just went out on my 14’ fusion and finding out that I gotta take the whole front end off to change the damn light is rather disappointing.
Great video! While I didn’t completely remove my front fascia, this video helped me do it just enough to get to my low beam and replace it. Thanks!
We picked up a brand new Fusion a few months ago with the sport and suspension package and I love everything about the car, except this. My only complaint about the car is the fucking headlights. Everything is LED except for the headlights and they have the dullest bulbs I have ever seen.
@Ungrateful Peasant - I agree. It's a pretty decent car but the headlights are the worst- by far- I've ever had in a new car. Total Magoo units.
I CANNOT BELIEVE THIS!
I thought it was joke video.
I still don't understand why the engineers did this?
Because they want you to take it to a Ford garage to be charged $100 or $200 in labor just to change a light.
Because most of these designs are done in third-party engineering firms that have no idea what they are doing.
Just to make sure you have to visit the dealership and give them more money
exactly!! its ridiculous to design something this way. Its like they are intentionally making repairs more difficult, even for a mechanic. It should take 5 minutes to replace a headlight bulb
What kind genius engineer is this wow!
Ford knows you'll have to go back to the dealer so they can soak you.
yes because I have a lift at my house to change a headlight bulb. what a joke
you can use a small socket to reach under the bumper... No lifting necessary
If you bought this vehicle, then deal with the repairs by going to a mechanic. ✌️
Nicely done Jon!
Good video guys, very informative! thanks
I replaced the side marker, foglight and low beam light bulbs on my 2013 Fusion. It was well worth the effort as the new lighting looks great and has improved visibility. But I agree, it should not have to be this difficult.
all that just to remove a headlight bulb?
@@stingerutube had a Malibu that required the same to change the headlight smh GM
super informative man! thanks!
This is why you research maintenance on a vehicle you like and are thinking about buying. I work on cars all day and people look at us like we are crazy when we tell them what it takes to perform simple services like this. We try to explain to people the requirements for oil and other fluids and they don't believe it. They think we try to sell shit that people don't need.
I’m an educated man but I can not speak to the habits of your garage. If you are busy week in week out and have repeat customers then my best guess is its probably not your work but no matter what the charge is an extremely high percentage of customers are going to negotiate for little penny while asking for more work. But that is old news so no need for any “research”. The problem with this video has nothing to do with the mechanic, his abilities or the way he walks us through the whole process. Here’s why the industry in which every Tom Dick and Harry must navigate at some point in life becomes a major expense AFTER shelling out tens of thousands of dollars! Even those who have done the Research! The facts are as follows: manufacturers (not just car companies)will cut corners, obviously hire the most ignorant engineers, use cheap labor overseas Mexico (definitely this one) costing us jobs in towns left to rot. Then after they have received all of the tax breaks they can scrounge up from tax attorneys and lobbyists, where they’ll have no problem paying them from the money saved by their piss poor engineers. They could care less about quality, safety, and the environment because no matter how wreck less they run the company….WE TAXPAYERS will always BAIL THEM OUT, thanks to BOTH PARTIES in Congress who have NO PROBLEM writing RUBBER CHECKS!
This video is one man who has worked hard to educate himself so he can share with others the process of changing a BULB! He didn’t create the problem and the company obviously doesn’t care about the problem they created because they did it for multiple years. The fact that you are able to tell everyone they should spend more time “researching” before they buy from this POS or that POS COMPANY while you piss and moan about how much the people questioning the shop working on their investment is disappointing! Maybe you should watch this video again and see if you have a clue about how much CAPITAL a single mother of two kids is able to afford to pay someone to change her light bulb!
Having done it myself, you can skip the part at 1:53 where he removes the two brackets for the fenders that the bumper attaches to. You can just simply pull the bumper off. Great video btw 👍
Sheesh, cleanest shop ever. Great vid
What type of bulbs did you use on the headlights? H11 and H7?
Only Ford could engineer something like this. Took me 45 min to change the low beam passenger side without taking the wheel well cover off. I have medium size hands and it was a total PITA!
Yeah great job Ford just convinced me keep car I have and can still replace bulb myself!😁😁😁
Why would 2 people dislike this video? It's very informative. Thank you for making it. I can't believe I bought a car that's going to take me a couple of hours just to change the light bulb. Huh.
Video is highly informative, I think the dislikes are just the fact of disliking having to remove all that just to change bulbs. Lol
What a fucking mission just to change or replace a light bulb... 'MERICA!!
i wonder if that applies to the fusion with out the grill shutter
Thank you so much for this video. It is super helpful!
I have yellow parking lights in the front. I'm assuming they're parking lights, because they turn on when I stop or park. They're right next to the brights, it's a 2016 model. So I have 3 bulbs within each light compartment, all together 6. Is this something not included with other models?
Gotta take apart the whole car just to replace a bulb?!?!?!?! Smh!!
What does the other end of that harness on the light plug into. I have only the plug in and need to order part but don't know what that sensor or whatever under the latch is..
NO COMMERCIALS, if most uploads are like this I am a subscriber.
I was so much into buying this. WAS!
Gone are the old days of reaching behind the headlamp assembly and twisting out the bulb without having to drop the front end clip. My goodness. Without a lift, you are screwed.
very good!
On models 06/09 is of same o diferent process to take of bumper out sr
Thanks so much
Wow... I really wish I looked into all this before I bought this car lol. Definitely not my 07 Camry...
You don't need to go through all that just to change the lights on a Fusion. We've owned several Fusions, headlight bulb change is very simple. All you need to do is remove the dust caps on the headlight housing to gain access.. If you want to install HIDs you may need to do all that., as the HID bulbs lack the right angle base that will allow for more leverage when locking in.
haw can I remove my right mirror on fusion 2015....Can you tell me pls...
Thank you!
Does the head light attach the the fender at all?
I got a 2017 ecoboost yesterday, I hate the yellow lights, but to do all this to just change some bulbs seems too much.
I just did it without removing anything. i pulled the little plastic piece thats right above the bulb, it has two 10mm bolts and a Torx bolt holding it in, then I removed the rubber cover and unplugged the driver side bulb with a screwdriver and twisted it out with 2 fingers, then while the bulb was out I pulled out as much wire as possible and plugged in the bulb outside of the assembly then worked it back in, it seems like there isn't enough room to get the bulb in but it fits even with the plug on it
how can i change the indicator bulb please.
This is for Ford Fusion 2010 and up, 2009 and down there is an access panel in the front passenger tire well.
Unbelievable but true. And after all this work the bulb does not lock into an up down position because the surrounding plastic ring does not have enough room . Which means you wedge it in or have terrible light reflection to the road.
Why why... amazing. When everything should be easy to do they do this....
Is there anyway to take the headlamp apart?
what did Ford need their own version of GMs 1.5hr to change headlights???
This is an excellent video. Very helpful. Easy to do. Thank you for Sharing.
OMG! I'd like to meet the engineer that designed that!!!!!!!! Count me out!
He was an instructor at Wyotech Long Beach.
How can we replace the third light from the back window? How much do you charge for helping me with that?
There's an easier way for the passenger side:
I removed two coolant reservoir bolts - lifted it up about 6" - and was able to reach the bulb access with one hand. With a bit of help from a long screwdriver to steady the wiring clip it was an easy replacement. 4 minutes.
oobleckboy yes it is all over UA-cam on how easy the bulb change is. This is crazy.
4 mins?! Dude dealership and pep boys say 3-5 hours. Lol where do u live I’ll give $60 to change it!
Other videos I've seen show how to access the driver's side bulb by taking out the air cleaner assembly. Nothing about removing bumpers. The passenger side is shown being accessed the same way more or less but still no bumper removal. I think there is an easier way, especially for one without a lift.
That was specially for the low beam so maybe that's why less work required. This is a ridiculous amount of work for headlight replacement.
BS. If you have small enough hands you can remove the bulb with taking apart the entire car. I just did.
AriesTatiGrrrl are you serious? this is what I am trying to do now. putting in high power silver star bulbs. So you really don't have to take the bumper off? anymore help would be fantastic. Thank you.
Grant D there is a good chance you could break the bulb doing that. and stay away from those silverstar bulbs or you will be replacing them again in about a year. go on eBay and buy some LED headlights. brighter than silverstar and you won't ever have to replace them again.
Thanks for the video, i reconnected the cables but now when i turn on it keeps telling that the hood is ajar, checked all connections and everthing looks fine, maybe ive forgot something?
@@Ryan-qe9ih yes, i checked under on the driver side there is a wire that was disconected, you have to loose the driver side to be able to see and grab the wire to reconnect
is there any other easier way to replace it?
I have a 2016 S ford fusion and went all over you tube and there's no way there are any short cuts. Removing the head light assy. is the only way to do it, So fellow mechanic just do it this way and really save time. And if your going to upgrade this is the only way.
FyI there are other ways to change the bulb without having to do all that if anyone is stressed. I know for my 2012 ford fushion if you have small hands you can easily reach in and take them out but if you don't you can just slighly remove the cover plate behind the bumper and reach in there.
Doesn't take much guys, just a few hex keys or "L" keys, a jack, jack stands to keep u safe and a skinny pointy Tool, or a flathead to pop all the clippings out, took me about an hour and a half but thats because I was smoking too 😂 I was hesitant to upload a video to show this can be done at home .
You didnt have to remove anything lol. This is like the only video that shows that. Just open hood, pop out the silicone cover behind the housing giving you access to bulb, reach in and twist socket 90 degrees and the bulb slides out. Reverse process to install new bulb thats it. Takes all of 2 mins haha. People removing the bumper and headlight housing must have hulk hands to not be able to do with just the hood open.
A lot of the newer cars and trucks are like this now...Acura is another one, but much more expensive for the bulb and igniter, if it needs that too...
Helpful video for removing lamp housings, but totally unnecessary for a simple bulb replacement.
Just replaced my low beam passenger headlight without doing any of this. All it took was removing the two hex, two bolts, and a little finesse. Took about 25 minutes or less.
How can I change the license plate bulb on the fusion 2016
+Heriberto Santos Great question! Why don't you give our tech support line a call and we can provide some more information on that. The number can be found at fmgaragegurus.com/About.aspx
That is an easy job. Look at the top of page 258 of the Owner Manual. The lamp uses a clip to attach to the trunk lid. Then pull the bulb out.
No tools needed!
What kind of tools?
what year is this Ford Fusion?
Holy Hell I hope my lights last a long time!
Great video. Ford wants you to spend money
I love that they put eight years of engineering into how to replace a lightbulb yet they can’t make an automatic transmission worth a shit.
Garage gurus
what year is this?
Hello, I am very interested in this vedio, it is helpful for me, I have the same headlight sold in Amazon, may I post the product link here, please? Thanks
Bruh are you telling me I basically gotta go back to the dealer to replace a headlight!
The designers of this model are either giggling, or committed suicide.
FUCK !!! .... I was thinking of changing out my wife's bulbs .... unbelievable.
My 2015 fusion's bulb just died yesterday, i went to mechanic to get a bulb and replace it. He said he had to take apart the whole front end, we both started laughing, until he stopped laughing first and said he was not joking. WTF is wrong with the ford engineers?
I did mine from top no removing bumper !!!
Remind me to never buy another Ford product again..., especially a Fusion.
Never mind, I don't think I'll ever forget this!!
I'm in my 70's..., I want my '65 GTO, 389, triple deuces back... Much easier to work on. LOL
Well I'm not sure what year this is.. But 2006 2007 era.. Its just a small panel to open in the wheel well. So check the. Wheel wells first folks.
Ford could've at least added some real HID projectors instead of the cheap halogen projectors, like that it would've been worth changing the bulb every 3-5 years.
The engineer that devolped this and the engineering manager that signed off on it have to be some real asses.
Priceless.You don't need to remove the bumper.I bet he gives incorrect road directions for chuckles too.
How much miles?
My low beam went bad at 27k miles. Be smart when you take the bumper off change ALL bulbs there.
@@michaelnelson2951 I have 46000 mi, and more than one lamp has not burned out
I got my 2014 fusion brand new and just now had to replace the lights. Thanks for the video because FUCK THAT SHIT. If I knew about this when I bought the car, I would have gotten something else.
Thanks for sharing & doing this vid … Can’t believe you have to go through all that crazy crap just to switch out headlight bulbs! … it’s definitely not just Ford doing this ; several other manufacturers are following same procedures … JUST PLAIN STUPID!
Practically is gone for American car maintenance!
Its obvious Ford did this replacement of hell in order to have their wonderful customers take them to ford service to give them more money. What a great way of showing gratitude for buying your brand. Definitely the last thing I buy from Ford!!!
It's much easier with a lift versus on your back with a jack style😎😎😎
I know what car not to buy thank you
This other video the guy only removed the top fasteners and the 3 by the wheel then pulled the top out enough to remove the headlight
As a product design engineer from automotive industry , these companies urge their design engineers to make complications in order to make more profit down the road. Greedy bastards.
😳😳I'm her right now at a mechanic changing these fucking lightbulb I remember I used to just reach my hand in take the light bulb and replace it myself this is crazy 😧
Did it today.H ourn a half.
this is fuckin crazy
I would love to know why he decided to be so extra to just change a bulb
Im surprised we dont have to take the engine out as well 🤣🤣🤣
Lol ikr
Fkn ford 😡
Hahahahaha Ford trying to become a Bmw
That’s coming very soon. What a joke really to change bulbs
im late but, thats a whole fact 😆😂🤣