Changing a starter clutch on a 150cc scooter
Вставка
- Опубліковано 10 вер 2024
- www.ebay.com/s...
www.joinhoney....
Try at own risk, is a big job don't do if you are not sure of your skills. Make sure to put some grease inside the crank seal not oil was mistake in video. I ended up with a leaking crank seal 2 months after doing this job so change the crank shaft seal while doing this job. Also be very careful torqueing the bolts i ended up stripping one at only 10ft pounds so i would not not exceed that the chart i used must be wrong.
Welcome to my channel i am shouting out my friend who has started her own apparel line called Uni kitten you can check it out here, thanks for the support. shop.spreadshirt.com/unikitten-apparel/
Just got had mines towed from the shop ,they had it for 2 months but thanks to this video I'll do it myself
great to hear let us know how you do.
Great video, very detailed, very helpful, thanks. Always doing these engines...
nice job on the video! you laid all the steps out perfectly.
That is usually from it burning oil. the oil inside was shifted when it fell on the side. the motor wasn't on the normal position. It should go away after a few mins.
Also , I'm not sure if that short amount of time ruined my gasket but in case it did, would it be okay to use high temp liquid gasket because I have a tube of that sitting around and I can't really afford to wait for a new gasket to show up because I use my scooter for work. I'm in the hospital right now for probably 4 or 5 days but as soon as I walk out of here I'm going back to work on that scooter. Thanks for any help you can give.
good video.. nice work. just what i had been wanting to know
I'm glad it helped you.
why for me it doesnt want to to come off? like its glued in permanently? ive been pulling it and yanking it. im sure thats not normal?
The starter clutch is glued? It's probably stuck on the wood ruf key.
Hello my scooter variator, belt and clutch spins very loose. And the rear wheel wont spin. The wheel is not seize up. Is this the fix I will need to get back on the road. Any help appreciated.
The belt might just be worn out. Or the variator weights are stuck.
yeah before like when you tried to start did it make like a loud buzzing or knocking sound
❤❤
Does this cause clicking ?y moped didn’t want to turn on today making a clicking noise so I think I need to change this
Depends, clicking could be a bad starter motor or bad battery.
like when you went to press the ignition switch in while holding the brake instead of it starting up all you would hear is a buzzing sound
+Bob Williams Yes it does that too it will just turn but wont turn the engine.
Do i need Loctite on the castle nut? I just installed a replacement heavy duty starter clutch and about 20 miles of city riding(so maybe 20-30 starts), its back to just the spinning sound when i try to start. Im praying to god its just because i didnt use Loctite and the castle nut just came loose. 🙏🙏🙏🙏🙏🙏🙏 🙏. Also, did you use a header gasket when reinstallingyour exhaust? Just curious.
Sorry for the late reply, Yes I had a head gasket. The nut should be tightened with an impact tool and use the correct spanner nut tool found on eBay. You can use Loctite but only use the blue one. I recommend it on the case bolts as well. Once its closed you cannot reuse a gasket. I don't like the gasket maker but you can use it but you cant ass oil for 24 hours and have to follow instructions on the tube. Regular gasket you can add oil after install and run the engine no waiting 24 hours. You can find a high quality clutch on eBay they are mostly sold in china so are hard to find it will look very different than the standard trash ones that are sold. Be careful they have the better version on amazon but its made of cast iron and will break when used, don't buy it. Read the reviews and the cast iron one has a different look to it.
Huge Help Ty So much 🤘👍🤘👍
You recommended a impact driver, but you didn’t use one yourself. Hense, the chain holding the tire down.
The Chain was there to secure the wheel from theft because it was taken apart. I did not have the spanner tool or an impact at the time.
When do you put the starter gear on?!!!
You can put it anytime, but you may need to maneuver the clutch and starter gear to get them to line up.
i gotta question i have a 150cc scooter and i dropped it on its side and white smoke came out the exhaust what could be wrong
Feels bad man two years
I have all the bolts took off but my side case ain’t coming off u know why?
Tap the sides of the cover with a rubber Mallett the gasket is holding it on. Also consider changing the crank seal while you got it open. Dont use high performance crank seals their too big and will leak.
@@chriss4365 thank you it worked
What happens when you forget to name the bolts taken out I cant find a diagram for bolt location and I dont wanna guess any help thanks
You can tell if it's the wrong size when you insert it. If it's wrong the bolt will stick out way too far. Otherwise mark each one and the cover with different color paint.
@@chriss4365 ok so I should be good then cause their all in,I'm gonna do the gasket on case over because I have a leak and starting to loose alot of oil,I did change my crank seal to a honda one its 2mm I hope its not that
@@Cito_Fiytb_617 find out where the leak is from. Only use scooter parts. I bet the crank seal is leaking. Open the cover if their is oil below the fan then it's the seal.
Did yours make a grinding noise when running?
Yes
chriss4365 alright now I know what needs replacing
when you tightened the nut for the starter cluctch looks like you stripped it it was tight then it slipped free
The wrench slipped off is all. Both parts are steel would be very hard to strip.
that's one hell of a long process.how do you know when its time to change the starter clutch? my scooter only has a few hundred miles, but now wont start, what does it sound like when the starter clutch fails?
You can usually tell if its turning by how it sounds. Have a friend look at the fan if it turns when you try to start it then the clutch is ok. If the clutch is bad it should make some noises when trying to start the bike and or the fan wont spin.
Guitars AndJams if you just need to know if starter is working take cover off where stator wires go into has 3 or 4 bolts think are #8 wrench try turning engine over with starter if fan housing is turning starter is working .now how did starter sound while trying starter if slow check batt voltage needs to be at least 11.5 volts for good turn over of motor.any questions i have most answers
what kind of sound did it make when you tried starting it up sir.
+Bob Williams Do you mean before or after the repair? The bike was very hard to start and you would hear a clanking sound when trying to start it and it would also stall the motor when able to start i guess it would lock up or something and stall motor.
Hi sir i have a question starter clicks solenoid clicks but not cranking starter clutch new
Not necessarily. Could be electrical issue or bad starter. You can remove the starter with a friend and hold the motor tight it will jump. Touch one of the bolt holes of the motor to the engine to ground it then have your friend start the bike and see if the starter spins.
My starter go with the wrong direction so that that starter clutch cant spin and the crankshaft cant spin
@@teambog167 it will only spin in wrong direction if the positive is switched to negative and negate to positive.
The red wire is possitive and starter are body ground?
I tested my starter motor i set the red wire ing negative and iconnext the ground in the positive and it spin correctly to engage the crankshaft
Dont u have the ratch special socket?
It is not necessary.
you should rename this video "Changing a starter clutch on a 150cc scooter". You will get more views this way.
6 years later here I am. Looking for a 150cc gy6... Great video. Thank you very much
hello sir how did you loosened the nut?
Proteus macapagal if you are referring to the nut on the starter clutch you use a adjustable wrench to remove it. It is reverse thread so turn it clock wise to remove it and counter clockwise to tighten. Don't follow the torque specs in my video they ended up being wrong. Snug the case bolts but be very easy to avoid stripping them.
What is the name of the special tool? Please help
What tool do you mean?
Its called a spanner nut tool i believe.
it made a noise while running. sounded like grinding.
and wouldn't start at all would it sir
just add the word stator clutch or starter clutch...
aray yar camera thoda dur rakho
Tamē śuṁ kahēvā māgō chō? Gūgala anuvāda
Cute ass