I have that exact model and i achieved it yesterday night. I had 3 pouch Li-Po batteries from old DELL Tablet Venue 7". I soldered them together and managed to fit them on the bottom, i had to break all the vertical fins supporting the plastic case. You can't notice them at all, no bulge no nothing, it's lightweight still... Each of them has 4100 mAh and i attached a module to recharge it which has micro-USB but still has + and - PADs to solder a charge port. I de-soldered the USB-C module wires + and - and soldered on in and out of the module and the USB-C port i soldered them to PADs on the module. Now it's battery powered and features a USB-C rechargeable port dedicated.
Thank you, I love this channel and found another one of yours.(Great, not bad processing, I have been following for a long time, I found your new channel under a different name about food and. camping. Great channel, thank you .)
Hello friend, I have been watching your videos for a long time and there are a lot of interesting and educational things in them. But in this video I don’t understand your choice for connecting batteries. You have 12 cells of 2.5Ah each, and you connect them in parallel and get a capacity of 30Ah, while the charging connector has a current capacity limit of 3A, therefore the full charge of your battery will be at least 10 hours. By increasing the voltage from 4.2V to 5V you lose about 20% on the dc-dc voltage converter, as a result the useful capacity will be no more than 24Ah. It would be more rational to use a 6s2p connection, while using a 5.5/2.1mm connector you can fully charge with a current of 3A in 1 hour and 45 minutes. In addition, it is possible to install a voltage converter for 5V in the downward direction, and such DC-DC converters have a higher efficiency, about 95%. It would also be possible to connect a type C dc-dc port converter to this battery and get the ability to quickly charge mobile devices, as well as charge the battery through a power delivery charger.
In a way what you say makes sense.....if fast charging is really that important then up the voltage and use USB PD But making a 1S battery and using a boost converter from 3.6V nominal to 5V will have much better efficiency than 24.6V down to 5V. Its the difference in the voltage you are starting inputting and then outputting that also affects the efficiency. Yes, buck converters are more efficient than boost converters TYPICALLY but there are different typologies and there are boost converters that are 95% efficient when the voltage difference is minimal. There are also 1S 3.6V USB PD powerbank boost boards that can do up to 22.5W like the SW6106 which I believe is the IC used on the "5V 4A Powerbank boost" board sold by TZT and others on Aliexpress. For higher power PD or other fast charging protocol then you're going to need 4S most likely. In that case use IP2368 or IP2366
Good video! It helped me to know how disassemble it. Btw, do you know why when I connect the fan a red light blinking? I bought this air cooler fan but it only worked for a couple of minutes and I really would like to repair it 😢.
quite opposite, shitload of cells in parallel means it'll charge and discharge slow which is great for longevity, balancing is not an issue since they all act as a single cell
Depends. If you need 65W+ output then you can build a MUCH better powerbank with all the output your heart desires for less than the $100+ you'd pay for one that has 100W+ output
Please make some mist cooler that can be put on the back if a normal electric fan, i have that kind of air cooler but the ice melts easily and not powerful enough need to be closer to the fan or mist
I have some things that contain lithium batteries, and I put them on the ground before leaving the house. I don't feel safe leaving them, and this, with this number of unreliable batteries, may make me never leave the house.😅
likn bro agr technical side se deekha jaye tou iss ma piezoelectric lagi hoi ha jo sirf pure distilled water contain karti ha bcz normal water ma bht sary small particles hote ha jo iss piezoelectric ko bht jaldi kharab kar sakta ha tou technical side se yeh product fail ha.
I have that exact model and i achieved it yesterday night.
I had 3 pouch Li-Po batteries from old DELL Tablet Venue 7".
I soldered them together and managed to fit them on the bottom, i had to break all the vertical fins supporting the plastic case.
You can't notice them at all, no bulge no nothing, it's lightweight still...
Each of them has 4100 mAh and i attached a module to recharge it which has micro-USB but still has + and - PADs to solder a charge port.
I de-soldered the USB-C module wires + and - and soldered on in and out of the module and the USB-C port i soldered them to PADs on the module.
Now it's battery powered and features a USB-C rechargeable port dedicated.
Now upgrade it's water tank to 30 liters 😂😊
Bro have a electronics store at home🗿
It is true! 🤣🤣
not. all products are introducing from there😅
It’s a repair shop, in countries that aren’t America; they actually repair stuff that breaks.
😂😂😂😂😂😂it's true
Because he's an engineer
It would be nice use the same USB-C port to charge the batteries.
Very nice!
The video is top notch as always! Continue in the same spirit 🎉🎉
Thank you, I love this channel and found another one of yours.(Great, not bad processing, I have been following for a long time, I found your new channel under a different name about food and. camping. Great channel, thank you .)
love from Bangladesh🇧🇩🇧🇩
Me
Same here
Take love from Bangladesh 🇧🇩
I live in Bangladesh 🇧🇩🇧🇩
জয় বাংলা
Please make power bank for laptop.
I'm your first subscriber❤❤❤❤
He's made a ton of those.
Thanks for the tutorial . First I will. But all the tools and machines worth 1000$ and I will be able to add the battery worth 5$ 😂
Your wark is so parfect 😊
Such a creative man❤️❤️
-love from Bangladesh 🇧🇩🇧🇩
Professional work 👍
You could attach a power bank at the bottom instead of doing so much work!
I noticed you have upgraded your spot welding machine pen
I'm using mine every day, it's a good product
i dont know what word can i say. your amazing brother.
Always love your works 🙏
Where I dreamed I would love to work😍🥰💗
Hello friend, I have been watching your videos for a long time and there are a lot of interesting and educational things in them. But in this video I don’t understand your choice for connecting batteries. You have 12 cells of 2.5Ah each, and you connect them in parallel and get a capacity of 30Ah, while the charging connector has a current capacity limit of 3A, therefore the full charge of your battery will be at least 10 hours. By increasing the voltage from 4.2V to 5V you lose about 20% on the dc-dc voltage converter, as a result the useful capacity will be no more than 24Ah. It would be more rational to use a 6s2p connection, while using a 5.5/2.1mm connector you can fully charge with a current of 3A in 1 hour and 45 minutes. In addition, it is possible to install a voltage converter for 5V in the downward direction, and such DC-DC converters have a higher efficiency, about 95%. It would also be possible to connect a type C dc-dc port converter to this battery and get the ability to quickly charge mobile devices, as well as charge the battery through a power delivery charger.
what ic does it use, mine burn out
In a way what you say makes sense.....if fast charging is really that important then up the voltage and use USB PD
But making a 1S battery and using a boost converter from 3.6V nominal to 5V will have much better efficiency than 24.6V down to 5V. Its the difference in the voltage you are starting inputting and then outputting that also affects the efficiency. Yes, buck converters are more efficient than boost converters TYPICALLY but there are different typologies and there are boost converters that are 95% efficient when the voltage difference is minimal.
There are also 1S 3.6V USB PD powerbank boost boards that can do up to 22.5W like the SW6106 which I believe is the IC used on the "5V 4A Powerbank boost" board sold by TZT and others on Aliexpress. For higher power PD or other fast charging protocol then you're going to need 4S most likely. In that case use IP2368 or IP2366
Oh amazing 😍🤩
Good like 😊😊
Student from Pakistan ❤
Bro, Which equipment don't you have?😂😂😂😂
should have 3D printer for making that extension battery case
He didn't have glue gun 😅😅
Hammer of thor😂
👍👍
@@minecrafttipsandtricks3543he have and used in many videos watching him from 7 to 8 years
Multimillionaire company upgrade 5$ fan🥵
amazing idea
Ótimo trabalho
Waste of time buy a power bank and attach to it thats it
yup dat real deal
Waste of time for us to see , not for him , he must have earn over over 20000 inr UA-cam revenue till today 😂 by posting this video only
@@neo9126 good one
Kam ka nahin hai isko kabadi mein fenk do😂😢
Bhai ye waste of time nahi Hain esa hain to Kya tum example de rahahu ki tumhare pass gehu hain or tum bahar se gehu ka aata late ho wo hain
❤ nice ideas
Damn. Look at all of those equipment.
❤❤❤ It's beautiful
Good video! It helped me to know how disassemble it. Btw, do you know why when I connect the fan a red light blinking? I bought this air cooler fan but it only worked for a couple of minutes and I really would like to repair it 😢.
哇塞，你这也太多玩样，比我们厂家还齐全
Good work 👏👍👌
Very nice look I am in Bangladesh
Simple solution just use a power bank😅
Or external battery power
Do not turn on the fan together with the humidifier as it ends up condensing and wetting the entire project below with splashes of water.
should cover all electronic with nail polisher
احسن مخترع❤
1s12p with no balancing that would change forever and die soon. Instead of using 6s2p with balance board that would charge quickly and work properly
Ты что осел ?
Why need balancing it's in parallel, in series it's hard to balance and maintain
quite opposite, shitload of cells in parallel means it'll charge and discharge slow which is great for longevity, balancing is not an issue since they all act as a single cell
LOL 1S and balancing? Balance what? And 24.6V nominal would FRY that fan's board.
where do you buy the material? It is very interesting 🙂 if you can open a shop you will become a millionaire man! 🤣🤣
Vote for face reveal
Ek Peltier modul bhi laga sakte hain pani thanda karne ke liye 😅✨✨
Nice mod 🥶
Isn't it better to buy a power bank simple? 🤷😂
If u have such equipment at home, why not to make own? :) Cheaper, you know what batteries you use instead 50% capacity chinese ones
Because he's an engineer not full
Depends. If you need 65W+ output then you can build a MUCH better powerbank with all the output your heart desires for less than the $100+ you'd pay for one that has 100W+ output
Sir tools video from India ANDHRA PRADESH STAE
Meu sonho é ter um quartinho desse cheio de equipamentos
15:39 definitely a rain machine for ants😅😅😅
Nice 👍🙂
Power bank would have been used instead
amazing
Nice👍🥰
Awesome 👍❤
so pintar de a base de azul pra fica original ficou bom o projetinho
Good
Brother plz make a Dc air conditioner using battery and solar Panel
Kipas angin itu membutuhkan ampere yang besar
Please make some mist cooler that can be put on the back if a normal electric fan, i have that kind of air cooler but the ice melts easily and not powerful enough need to be closer to the fan or mist
Motorsiklet videolarını bekliyoruz
Love it
❤❤❤
I will pay 30$ sell me whole fan with this battery system
I have some things that contain lithium batteries, and I put them on the ground before leaving the house. I don't feel safe leaving them, and this, with this number of unreliable batteries, may make me never leave the house.😅
If the water is cold, it will sublimate. The water will fall and you will encounter an electronic unit.
how long does charging take?
Please upgrade the motor 😊
make a video
upgrade the fan motor
মাশাআল্লাহ
What kind of engine does it have?
vai charging output?
Hello the spot welding machine do you sell this machine?
this is not for a normal person to upgrade.you will make the whole electronic store thats why you should buy a power bank.😁
It's very hot now my friend 🥵🥵🥵🥵
Can upgrade the fan strong wing ？？
Bro u keep the whole electronic shop in your home?
Can u help me with the center point on BMS mentioned as T. What is the use of T point ?
likn bro agr technical side se deekha jaye tou iss ma piezoelectric lagi hoi ha jo sirf pure distilled water contain karti ha bcz normal water ma bht sary small particles hote ha jo iss piezoelectric ko bht jaldi kharab kar sakta ha tou technical side se yeh product fail ha.
Izin bang request power Bank jumbo
Bro just have an entire market at home
Kitne Tak mil jaega mini cooler
Superv❤
Bruh with peltier please 😢 it's 48°c in PHIL!
peltier module draw 12v 6a an hour, it will deplete battery pack so fast
Đồ thiên tài độc ác điên khùng! Điều gì tiếp theo trong tâm trí nhà phát minh của bạn. Video tuyệt vời. Chúc mừng! (thanks to Google Translate!)
Price after making?
5$ upgrade with 500ish$ tool
Upgrading Battery bank is ok but what about water tank ?
Palabras mayores!
Hi buddy..
How to make an electric hydrofoil boat?
Only you can show us this..
Can you upgrade it's morot please
你们那边卖多少钱
Нарешті вже показує схему підключення а то що куди і як не зрозуміло раніше було це ж дурдом...
How to buy battery?
Name the equipment you don't have 😂😂
Bro, can you sell a fan like that? I'll buy it later, but don't make it too expensive, okay?
Sir? Can i have some of your old batteries?😭
Battery backup
Is fan ki air saime child hoti h
Как можно поменять ночник в этом вентеляторе что бы ярче светил,можете видео зделать?
Why can't we use a power bank......😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂
Just waste of time 😅😅😅😅