My friends joke about me having a tool fetish. I definitely can watch a full breakdown of your toolbox. It’s always nice to know what tools i can buy to enjoy twice in my life.
2 things I’ve come to appreciate: Step drills; awesome to open up any hole size just a bit. Some garden hose on vice grips. Great for clamping off any soft hose like a radiator hose or fuel line.
Adding on to the discussion about the Tajima sockets (if someone hasn't mentioned it) - you can get 1/4 socket adaptor bits to fit an impact driver. I picked up a set from Bunnings (I think they were Irwin branded) that included 1/4, 3/8 and 1/2 socket adaptors. They're usually found in amongst the drill/driver bits I wouldn't trust them for anything high torque but they're super useful for assembling small stuff
I'm mostly a woodworker but this is the same: starting with a cheaper tool can show you if it's useful in your shop. If it's not, no big loss. If you find you're using a tool on a regular basis, it might make sense to upgrade to a better version.... usually when it breaks.
Thanks for the tip on and adjustable AN wrench. I didn't know about the nut size differences. For brake stuff, I've grown to love my locking adjustable wrench. Stanley 85-610. They have smooth jaws. All the others that I've seen have serrated jays and they will gouge soft fittings. Good for holding things while grinding too.
To all the Aussie crew, TradeTools’ Force double ended long ring spanners are some of the best I have used. Great form factor, especially for when you are leaning on them.
I went out and almost immediately (after picking my jaw up off the floor) bought one of those radiator funnels after seeing it on your channel some years ago. Yes, they are amazing!
The screwdriver with socket on end is called nut drivers. With the hex key sockets the best tool is the 1/4" screwdriver which can make getting screws out quicker. For dash work the 450 mm long 1/4" extension makes life so much easier. They aren't common, one of the few tools I had to buy Stahl Wille brand.
Flank drive spanners come in different hex offset to the angle of the handle too and a combination of inline and offset has been handy for bell housing bolts over the years. More so in tight conversions up against the firewall
I would have put the impact driver gun at #1 position as biggest time saver, although I dont get the fuss over the impact driver sockets, i just have a 1/4 and 3/8 square drive adaptors and use my normal sockets, along with a 1/4 bit drive adaptor and bit set And I used to be a Ryobi guy but since switched to Milwaukee M12 and it changed my life.
After seeing a Milwaukee youtube ad for Step Drills, I bought a set the next day. The best thing ever. I would like to see more of Benny's workshop tools.
Recently had to buy another rollcab because I ran out of room. Id love to see the tools you have modified or created to get certain jobs done. As a fellow mechanic myself, who works for an Auto sparky, I know youd have a few.
If anyone reading this does Carpentry … the company, Tajima, that he mentions regarding the 1/4” bits… best chalk lines and caulking guns ever made. It’s insane how good they are relative to the standard.
Magnetic sockets and locking extensions for when working in hard to reach places you don't want to lose a fastener. And dead blow hammers as more force is transferred then regular hammers
Not wrong about the Japanese 1/4" hex sockets, I use a Japanese brand and had to do the same thing. I just put them in a vice and went along with a grinder with a cutting wheel. The sockets I use are 1/4" hex drive deep socket with a flex joint, those things have been a god send.
Benny, Wurth, does the step drill bits metric in .5mm increments from 1 to 13 mm. We use them all day at work and can also get them loose if you lose them or break or blunt them
Benny, have you ever tried the 'right angled' ratchets where you can put the socket on and it looks like and can operate as a standard ratchet, but also if you twist the 'grip' on the handle it will also rotate the socket? really useful in REALLY tight spaces
Mate awesome episode... No one ever explains this stuff, sometimes it feels like "pre requisite knowledge" is needed just to watch a UA-cam show.... Kinda sux so thanks.
totally agree with Benny , most starter / apprentice tool bundles are bulked out with stuff you will never need .. if you're starting out i think it's much better to get a 2nd hand box & pick up tools as you realise you will need them
It's also worth checking what you get for spending a little bit more. Sometimes there is a big jump in quality, or a set with slightly more in for not a lot more money.
Agreed, i went cheaper on my roll cab, I don’t roll it around and I’m not an every day spanner spinner. Ive built myself quite a kit over the years. Buy quality stuff where you can.
Benny, love the vid mate, just add onto your flare nut spanners the 17/19 and 22/24 are invaluable too!!! Think diesel injectors, high pressure power steering lines etc, those sizes I got teased for buying by my boss and then he had to come to me tail between legs to borrow my 17/19 on an old tata diesel fuel injector pipes. 😂
If you can afford it, buy an impact wrench/rattle gun/whatever you wanna call it. Spent so many years needlessly fighting bolts with breaker bars and spanner combos. I still like to put bolts back in with manual tools to feel if its binding, but rattling stuff out is a dream.
You may not be able to sharpen those step style drill bits but if they became too blunt you can always grind them into a regular drill bit and give them a second life
Great video! This is one that could go on for hours, but I like how you covered the essentials and not the brand but the tool itself. In America we get wrapped around needing to have a certain brand when in reality it's not the brand it's the tool that completes the job. Certain things you can cheap out on however drill bits are definitely not one of them 😂 ask me how I know?
There are some great tools there that I don't have. I definitely need some of those socket mounted spanner heads They would have saved me a lot of headaches.
Transmission mechanic here. My top 5 tools would be: Impact gun with a 3/8 socket adapter- makita is my brand, electric ratchet - I have Milwaukee and Matco, a good set of picks - anything with a lifetime warranty but I have snap on, flexible magnetic socket organizers - I have ezred. They really are convenient to move around while you work, Long shank, flex head, offset ratcheting wrenchs - mine are Platinum branded - I think they are sold under Mountain now, but Matco and Harbor Freight also have them. They are my favorite hand tool and one of the best investments in my tools box
Can you do a similar video on tools to avoid/ ones you eventually got rid of? I really enjoy trying to keep a minimal toolset but the world is full of tools that claim to solve problems
Buying up a bulk lot of misc tools used solely for butchering is happening. Meams that if your in a pinch and can modify a tool to work then you dont need to hack up your main tools. The amount of times ive cut up a spanner or ground down a socket to work has being more beneficial than buying a specific tool for 1 job
The single tool that made the biggest difference for me was getting a slip joint plier or spring clamp pliers as I call them, being able to easily remove difficult spring clams like the big ones Toyota used on intake hoses or really strong radiator clamps is worth the price of admission imo. the snap on ones are great if you can afford them, I have one made by jimy tools which I find more ergonomic, I usually pick them up before my snap on’s but I’m not sure if they’re made anymore.
Those tajima impact driver bits arnt a stocked line but I’m fairly confident they’re able to be ordered in at total tools If I remember I’ll have a sus in the morning
Cheers Benny for this video. I work on Subarus predominantly, like your younger self, with a few FWD Toyota 4s and 6s thrown in. I find Koken slim line 1/4” are useful for tight spaces. Also the long flex 3/8s are great for like reaching down the side of frame rails. Also specialty tools like cam gear holders are invaluable but if you can weld up a makeshift tool, do it. I don’t have a crank pulley holding tool, so just jam a socket and extensions in and bump start to remove. Trained collision repair tech, enthusiast mechanic. :)
My fav tool in your arsenal is still that brake cleaner bottle. You helped me figure out sourcing one but here in the Murika they are SO insanely overpriced its prohibitive to buy one... and thats the way the crooks here want it. I would love to get one but its the cost of 3 cases of generic spray cans (plus the drum of cleaner).
T&E tools do a spanner set called Dolphin spanners. They are now my absolute go to spanner. Strange looking design but allow you to push on the flat surface when using the ring end and fits all kinds of strange angles
benny. yes the japanese 1/4" hex bits, they are slightly longer than the usa/aus gear. I bought a specific JDM Makita impact driver to run my jdm bits. I absolutely love it. might be worth getting a jdm makita impact driver, and using a makita to ryobi battery adaptoer!
Do you have a go-to brake bleeding setup? Some kind of fancy compressor powered one or anything? Or are you still on the hose-into-the-emptybottle technique?
I have my SAE rollcab for working on the racecar, a Metric rollcab, many modified & specialty tools acquired over 40 years & all my specialist radio tools etc. Plus my red power tools because I am a poser!
Less mechanical loss as the 1/4 mandrel is pressed in? They look cool? They’re from Japan? No idea, I just like them and they get asked about in every single episode I use them in
@@BennysCustomWorks and you literally answered my question.. i looked for these in japan and didn’t see them. Closest thing I’ve found in aus is motorbike ones from motion pro but their not as deep.
Kinchrome do the flexible screwdriver with a 1/4" drive. I got the full sidchrome set as an apprentice, but worked on American, Australian and European buses and trucks. So i just have heaps of tools.. Gearwrench ratchets are as nice as snap on but 1/3 of the price now with snap ones price increase in the past year.
I had a flex head gearwrench the same as the snap on one I showed. They discontinued the one I had then it stripped out and couldn’t be replaced . That’s one good thing about snap on, you can get rebuild kits pretty cheaply once you’ve purchased the ratchet
@@BennysCustomWorks yes, gearwrench is a replacement when the pawls wear out, but they are $100 vs $400 now. I've rebuilt my snap on 1/2" flex head ratchet in every function more than once in twelve years being used on trucks. I know to use them not as breaker bars too.
few things. I find most of the new sockets that have the sizes printed on suck.... only buy stuff with it stamped in. Milwaukee elec soldering iron, never go back to gas or leads. And those quick solder joiners are a godsend under dash’s etc, worth the money when you need them, good for a breakdown kit also cause you only need a lighter. And over the years i made a habit of never leaving a tool shop empty handed and find myself buying random stuff.
One tool that I think are a godsend, are swivel/universal sockets. They can be so bloody handy in a tight spot like starter bolts or bellhousing bolts where you can't get to a fastener straight on, IMO the Snap-on ones are the best because the joint is tight enough that you can set the angle you need and it wont flop on you but still loose enough to work effectively - BUT - (hot tip) don't buy the Snappy ones - buy the Caterpillar ones (Made by Snap-On and cheaper) 3/8 drive imperial 3/8-3/4 p/n 9S-1747 and 3/8 drive metric 10mm-19mm p/n 9U-6124 1/2 drive imperial 1/2 - 1-5/16 p/n 246-8184 (I cant find the p/n for metric in 1/2"), Most Caterpillar hand tools are made by Snap-On and are considerably cheaper from a Cat dealer as opposed to the SO truck.
I wish I used my tools enough to warrent buying a heap, or better quality ...... but really can't justify it lol I bought a 200-300 metric only SP tools kit on sale with a discount code. Few extra things purchased here and there. A random set of imperial spanners and a socket set on a blackfriday sale good to goooo
My name is Elizabeth I’m 29 years old , I love car repair which am going to start today am in Germany am very excited about my first day in car repair shop hopefully in future I become a supper professional Car mechanic repair ❤❤
A spark plug gapping tool, it is cheap, handy, and accurate, and looks more professional than hitting the plug on a bench or wall and hoping you haven't gone to far when you check it with your feeler gauge, which I always seemed to do every time gapping plugs. Nearly, nearly, nearly, ah fark it to far
Gotta say Ben, I bought stuff from sparesbox because you offered a discount code.. what a shit it's been getting in contact with in regards to an order terrible customer care
When it comes to tools you get what you pay for. Snap On tools may be very pricey, But you will spend less time replacing them under warranty then the cheaper brands. Now keep in mind. This is if you are using these tool everyday as your job. For you weekend warriors and Harry Homeowners. The cheaper tools that carry a lifetime warranty will work well for you. I have learned this the hard way. This stuff is my daily job and I have been doing it now for 33 years.
As a qualified heavy duty diesel technician, the big expensive brands simply don't make financial sense for the home gamer. Yeah I know, your spanners having Snap-On written on them is very cool, but for example half the shit in my toolbox is KC Tools stuff. Because for something you're not going to be beating on every day, they're MORE than good enough and somewhere around 1/3 the price. How often DO you use a 30mm spanner, really?
Hence me saying I’m showing the tools not the brands we’re discussing. I picked up a sweet deal on a 21-36 bluepoint spanner set at a swap meet that were barely used.
I only watched to comment, no offence but your content has gotten very boring and irrelevant in my opinion as a viewer, long uninteresting videos just because you do it once a week.. goodluck but I’m out sorry.
I’m sorry it was wrong of me to say, I was just being irrational. I guess I just wanted more than a tool video, but that’s me. I’m sure it helps a lot of people it to me just won’t help my situation. But again it’s for a broader community not just myself so again, I’m sorry. I will continue to watch
My friends joke about me having a tool fetish. I definitely can watch a full breakdown of your toolbox. It’s always nice to know what tools i can buy to enjoy twice in my life.
Yep agree, full tour of toolbox be magic.
2 things I’ve come to appreciate:
Step drills; awesome to open up any hole size just a bit.
Some garden hose on vice grips. Great for clamping off any soft hose like a radiator hose or fuel line.
I've been a mechanic over half of my lifetime and only recently bought a stepped drill bit, and I wonder how I ever made it without one. 😂
Waiting for this all day yeah da boyz
Adding on to the discussion about the Tajima sockets (if someone hasn't mentioned it) - you can get 1/4 socket adaptor bits to fit an impact driver. I picked up a set from Bunnings (I think they were Irwin branded) that included 1/4, 3/8 and 1/2 socket adaptors. They're usually found in amongst the drill/driver bits
I wouldn't trust them for anything high torque but they're super useful for assembling small stuff
Impressed by that drill but set. I hadn’t heard of these. Always good to know of a high quality drill bit set.
They’re bloody awesome!
Those stepped style drill bits are available from Würth, called Smart step. Offered in sets and separately.
@beenyscustomworks any reason you don’t have a battery ratchet wrench? I think they’re amazing, really speeds things up
I have been replacing a lot of suspension components lately. Dead-blow hammer, pry-bar, breaker bar, 3 jaw puller and press tools and torque wrenches.
I'm mostly a woodworker but this is the same: starting with a cheaper tool can show you if it's useful in your shop. If it's not, no big loss. If you find you're using a tool on a regular basis, it might make sense to upgrade to a better version.... usually when it breaks.
My favourite recent addition to my toolbox is hose clamp pliers. $40 and saves so many headaches if your car has the spring style clamps.
These are a god send. I thought they were useless at first until I used them.
Lisle 47900 Hose Remover Pliers
These are a must as well, I don't know how I made it without them.
Thanks for the tip on and adjustable AN wrench. I didn't know about the nut size differences.
For brake stuff, I've grown to love my locking adjustable wrench. Stanley 85-610. They have smooth jaws. All the others that I've seen have serrated jays and they will gouge soft fittings.
Good for holding things while grinding too.
To all the Aussie crew, TradeTools’ Force double ended long ring spanners are some of the best I have used. Great form factor, especially for when you are leaning on them.
Crows foot spanners are also in impact grade too when all the leverage is needed too but have never had a normal one fail yet
Benny, Sydney Tools has those Drill bit sets in metric (Xtorque Brand), available in a couple different varieties, ie Colbolt, Ti coated etc.
I went out and almost immediately (after picking my jaw up off the floor) bought one of those radiator funnels after seeing it on your channel some years ago. Yes, they are amazing!
The screwdriver with socket on end is called nut drivers.
With the hex key sockets the best tool is the 1/4" screwdriver which can make getting screws out quicker.
For dash work the 450 mm long 1/4" extension makes life so much easier. They aren't common, one of the few tools I had to buy Stahl Wille brand.
I Would definitely be keen on a full toolbox tour, even a look over welding equipment and power tools.
Flank drive spanners come in different hex offset to the angle of the handle too and a combination of inline and offset has been handy for bell housing bolts over the years. More so in tight conversions up against the firewall
Magnet bar tool holders that mount on the wall, great time saver for high use stuff
I would have put the impact driver gun at #1 position as biggest time saver, although I dont get the fuss over the impact driver sockets, i just have a 1/4 and 3/8 square drive adaptors and use my normal sockets, along with a 1/4 bit drive adaptor and bit set
And I used to be a Ryobi guy but since switched to Milwaukee M12 and it changed my life.
Tbh I had the sockets before I realised the adapters existed but it’s the most asked about tool we use on the channel by far
One of my favourites is the rivnut gun. Handy bit of gear.
build for what you own, my case its 8-10-12mm t-bars and JIS screw drivers (vessel impacts) mostly motorbike stuff
I hit pause 5 times and put 5 tools, all for around a tenner, in my Amazon basket that I know are going to make my life better 😊👍
After seeing a Milwaukee youtube ad for Step Drills, I bought a set the next day. The best thing ever. I would like to see more of Benny's workshop tools.
Recently had to buy another rollcab because I ran out of room. Id love to see the tools you have modified or created to get certain jobs done. As a fellow mechanic myself, who works for an Auto sparky, I know youd have a few.
Custom tool #69. Got a drawer of them also haha!
Please more tool vids!!
Also would appreciate your opinion on Torque Wrenches, value, styles and accurate results.
i think having a sutible caliper rewind tool for the calipers with handbrakes (brumbies and l series come to mind) over using pliers is a good one
If anyone reading this does Carpentry … the company, Tajima, that he mentions regarding the 1/4” bits… best chalk lines and caulking guns ever made. It’s insane how good they are relative to the standard.
Magnetic sockets and locking extensions for when working in hard to reach places you don't want to lose a fastener. And dead blow hammers as more force is transferred then regular hammers
Not wrong about the Japanese 1/4" hex sockets, I use a Japanese brand and had to do the same thing. I just put them in a vice and went along with a grinder with a cutting wheel. The sockets I use are 1/4" hex drive deep socket with a flex joint, those things have been a god send.
Benny, Wurth, does the step drill bits metric in .5mm increments from 1 to 13 mm. We use them all day at work and can also get them loose if you lose them or break or blunt them
Benny, have you ever tried the 'right angled' ratchets where you can put the socket on and it looks like and can operate as a standard ratchet, but also if you twist the 'grip' on the handle it will also rotate the socket? really useful in REALLY tight spaces
Mate awesome episode... No one ever explains this stuff, sometimes it feels like "pre requisite knowledge" is needed just to watch a UA-cam show.... Kinda sux so thanks.
What do you keep on-hand in rattle cans? What're your go-to sprays or chemicals to get you stuck, or unstuck?
We have very little need for magic sprays in Aus tbh as rust is minimal. I just use the Valvoline WD Spray as my general go to .
I’ve finally found one that works, Wurth rost off black, it has graphite in it and it works well even when a thread grabs.
Superb video as always!
totally agree with Benny , most starter / apprentice tool bundles are bulked out with stuff you will never need .. if you're starting out i think it's much better to get a 2nd hand box & pick up tools as you realise you will need them
If you are at a dealer, yes I'd agree.
It's also worth checking what you get for spending a little bit more. Sometimes there is a big jump in quality, or a set with slightly more in for not a lot more money.
Agreed, i went cheaper on my roll cab, I don’t roll it around and I’m not an every day spanner spinner. Ive built myself quite a kit over the years. Buy quality stuff where you can.
Benny, love the vid mate, just add onto your flare nut spanners the 17/19 and 22/24 are invaluable too!!! Think diesel injectors, high pressure power steering lines etc, those sizes I got teased for buying by my boss and then he had to come to me tail between legs to borrow my 17/19 on an old tata diesel fuel injector pipes. 😂
Saw the super stubby 1/4" drive ratchet on the truck and couldn't figure out a use. Now I'll be grabbing one next time they come around...
Long series flat ring spanners were a great investment, the brand I bought replace them no question when I break one 😊
If you can afford it, buy an impact wrench/rattle gun/whatever you wanna call it. Spent so many years needlessly fighting bolts with breaker bars and spanner combos. I still like to put bolts back in with manual tools to feel if its binding, but rattling stuff out is a dream.
You may not be able to sharpen those step style drill bits but if they became too blunt you can always grind them into a regular drill bit and give them a second life
Great video! This is one that could go on for hours, but I like how you covered the essentials and not the brand but the tool itself. In America we get wrapped around needing to have a certain brand when in reality it's not the brand it's the tool that completes the job. Certain things you can cheap out on however drill bits are definitely not one of them 😂 ask me how I know?
There are some great tools there that I don't have. I definitely need some of those socket mounted spanner heads They would have saved me a lot of headaches.
17:55 why not a hex to socket adapter
Great video Ben thanks alot for sharing this info definitely need to get some rachet spanners for myself !
Transmission mechanic here. My top 5 tools would be: Impact gun with a 3/8 socket adapter- makita is my brand, electric ratchet - I have Milwaukee and Matco, a good set of picks - anything with a lifetime warranty but I have snap on, flexible magnetic socket organizers - I have ezred. They really are convenient to move around while you work, Long shank, flex head, offset ratcheting wrenchs - mine are Platinum branded - I think they are sold under Mountain now, but Matco and Harbor Freight also have them. They are my favorite hand tool and one of the best investments in my tools box
Can you do a similar video on tools to avoid/ ones you eventually got rid of?
I really enjoy trying to keep a minimal toolset but the world is full of tools that claim to solve problems
Buying up a bulk lot of misc tools used solely for butchering is happening. Meams that if your in a pinch and can modify a tool to work then you dont need to hack up your main tools. The amount of times ive cut up a spanner or ground down a socket to work has being more beneficial than buying a specific tool for 1 job
The single tool that made the biggest difference for me was getting a slip joint plier or spring clamp pliers as I call them, being able to easily remove difficult spring clams like the big ones Toyota used on intake hoses or really strong radiator clamps is worth the price of admission imo.
the snap on ones are great if you can afford them, I have one made by jimy tools which I find more ergonomic, I usually pick them up before my snap on’s but I’m not sure if they’re made anymore.
I love my double flex kabo ratchet spanners.
I've had to warranty a few of mine I use Kabo at home now and Bluepoint at work just for the easy on truck replacement.
Those tajima impact driver bits arnt a stocked line but I’m fairly confident they’re able to be ordered in at total tools
If I remember I’ll have a sus in the morning
Hard to beat Stahlwille tools.I found Snap on no good for hydraulic work
I love tools and this video was great! Do more of these. I cant be the only one who is obsessed with tools.
Cheers Benny for this video. I work on Subarus predominantly, like your younger self, with a few FWD Toyota 4s and 6s thrown in. I find Koken slim line 1/4” are useful for tight spaces. Also the long flex 3/8s are great for like reaching down the side of frame rails.
Also specialty tools like cam gear holders are invaluable but if you can weld up a makeshift tool, do it. I don’t have a crank pulley holding tool, so just jam a socket and extensions in and bump start to remove.
Trained collision repair tech, enthusiast mechanic. :)
a telescopic or bendy magnet, no matter how long you are in the trade, you always drop a bolt or a nut in the most hard to reach places...
I live in the US and don't have a that many Imperial tools, my only need is automotive use and since all my vehicles are JDM it's all metric...
My fav tool in your arsenal is still that brake cleaner bottle. You helped me figure out sourcing one but here in the Murika they are SO insanely overpriced its prohibitive to buy one... and thats the way the crooks here want it. I would love to get one but its the cost of 3 cases of generic spray cans (plus the drum of cleaner).
T&E tools do a spanner set called Dolphin spanners. They are now my absolute go to spanner. Strange looking design but allow you to push on the flat surface when using the ring end and fits all kinds of strange angles
Force tools at Tradetools are pretty good quality. Can't fault their socket sets.
If you do a lot of Ip tie work, flush cut pliers are great for keeping you and your mechanic from cutting themselves on jagged zip tie ends.
benny. yes the japanese 1/4" hex bits, they are slightly longer than the usa/aus gear. I bought a specific JDM Makita impact driver to run my jdm bits. I absolutely love it. might be worth getting a jdm makita impact driver, and using a makita to ryobi battery adaptoer!
Been spannering for 25 years evenings and weekends. A few of these I don't have and I will be finding the glug jug for the rad for future use
Worth the money for sure. They aren't that cheap for basically a funnel.
Hey Benny, Wurth do the step drill bits in both imperial and metric, and in sets and singular.
Gteat video
This needs to be a monthly feature.
Awesome vid. Very helpful.
Do you have a go-to brake bleeding setup? Some kind of fancy compressor powered one or anything? Or are you still on the hose-into-the-emptybottle technique?
I have a vac bleeder and a pressure bleeder. But tbh nothing beats pumping the pedal old school
Good stuff
What about top 10 tools (give or take) for a p plater to carry that'll get them out of trouble.
I have my SAE rollcab for working on the racecar, a Metric rollcab, many modified & specialty tools acquired over 40 years & all my specialist radio tools etc. Plus my red power tools because I am a poser!
Would like to know what torches/lighting you use. I want to invest in some torches but I despise micro USB which still seems to be common
Good stuff Benny!
Great educational video!
Why would you use those tajima sockets over a impact wrench with deep sockets?
Less mechanical loss as the 1/4 mandrel is pressed in? They look cool? They’re from Japan? No idea, I just like them and they get asked about in every single episode I use them in
@@BennysCustomWorks and you literally answered my question.. i looked for these in japan and didn’t see them. Closest thing I’ve found in aus is motorbike ones from motion pro but their not as deep.
Something similar to the tajima on Amazon by Wiha unless I'm wrong
Talk about cool tools from Japan so I can stock up next time I go
Kinchrome do the flexible screwdriver with a 1/4" drive.
I got the full sidchrome set as an apprentice, but worked on American, Australian and European buses and trucks. So i just have heaps of tools..
Gearwrench ratchets are as nice as snap on but 1/3 of the price now with snap ones price increase in the past year.
I had a flex head gearwrench the same as the snap on one I showed. They discontinued the one I had then it stripped out and couldn’t be replaced . That’s one good thing about snap on, you can get rebuild kits pretty cheaply once you’ve purchased the ratchet
@@BennysCustomWorks yes, gearwrench is a replacement when the pawls wear out, but they are $100 vs $400 now. I've rebuilt my snap on 1/2" flex head ratchet in every function more than once in twelve years being used on trucks. I know to use them not as breaker bars too.
Tools for working on car electronics 🙂
Tools for the bedroom
I'd be happy if Benny broke the internet doing a tool box tour.
few things.
I find most of the new sockets that have the sizes printed on suck.... only buy stuff with it stamped in.
Milwaukee elec soldering iron, never go back to gas or leads.
And those quick solder joiners are a godsend under dash’s etc, worth the money when you need them, good for a breakdown kit also cause you only need a lighter.
And over the years i made a habit of never leaving a tool shop empty handed and find myself buying random stuff.
One tool that I think are a godsend, are swivel/universal sockets. They can be so bloody handy in a tight spot like starter bolts or bellhousing bolts where you can't get to a fastener straight on, IMO the Snap-on ones are the best because the joint is tight enough that you can set the angle you need and it wont flop on you but still loose enough to work effectively - BUT - (hot tip) don't buy the Snappy ones - buy the Caterpillar ones (Made by Snap-On and cheaper) 3/8 drive imperial 3/8-3/4 p/n 9S-1747 and 3/8 drive metric 10mm-19mm p/n 9U-6124 1/2 drive imperial 1/2 - 1-5/16 p/n 246-8184 (I cant find the p/n for metric in 1/2"), Most Caterpillar hand tools are made by Snap-On and are considerably cheaper from a Cat dealer as opposed to the SO truck.
That TOOLS is the amazing Well done Benny
Best spanner flipper in the business
I wish I used my tools enough to warrent buying a heap, or better quality ...... but really can't justify it lol
I bought a 200-300 metric only SP tools kit on sale with a discount code. Few extra things purchased here and there.
A random set of imperial spanners and a socket set on a blackfriday sale good to goooo
My name is Elizabeth I’m 29 years old , I love car repair which am going to start today am in Germany am very excited about my first day in car repair shop hopefully in future I become a supper professional Car mechanic repair ❤❤
What do you do with fluids removed from car? How where do you dispose of them?
You know mechanics are on another level when they say “My 3/8th Socket Drawer” like, I have a “Socket Drawer”. One. Single. That’s it.
I will watch an hour long video on your toolbox
A spark plug gapping tool, it is cheap, handy, and accurate, and looks more professional than hitting the plug on a bench or wall and hoping you haven't gone to far when you check it with your feeler gauge, which I always seemed to do every time gapping plugs. Nearly, nearly, nearly, ah fark it to far
I just bash it against something :D
You didnt mention the ball ends on the hex bits.
pipe wrenches 😎
Was in japan in oct, tried to find those fancy hex drive impact sockets you guys use. What brand are they mate?
Your preference on torque wrenches/ brands
I have a digital snap on but used to have a kincrome micrometer type adjustment 1/2 wrench
Gotta say Ben, I bought stuff from sparesbox because you offered a discount code.. what a shit it's been getting in contact with in regards to an order terrible customer care
Gian, Would you consider Benny as a "Tool"? 🤣🤣🤣
When it comes to tools you get what you pay for. Snap On tools may be very pricey, But you will spend less time replacing them under warranty then the cheaper brands. Now keep in mind. This is if you are using these tool everyday as your job. For you weekend warriors and Harry Homeowners. The cheaper tools that carry a lifetime warranty will work well for you. I have learned this the hard way. This stuff is my daily job and I have been doing it now for 33 years.
As a qualified heavy duty diesel technician, the big expensive brands simply don't make financial sense for the home gamer. Yeah I know, your spanners having Snap-On written on them is very cool, but for example half the shit in my toolbox is KC Tools stuff. Because for something you're not going to be beating on every day, they're MORE than good enough and somewhere around 1/3 the price. How often DO you use a 30mm spanner, really?
Hence me saying I’m showing the tools not the brands we’re discussing. I picked up a sweet deal on a 21-36 bluepoint spanner set at a swap meet that were barely used.
Take out tools!? Blasphemy! I just get more toolboxes.
OBD acanners
I want to marry him if he’s not married ❤
Moist
Indeed
I only watched to comment, no offence but your content has gotten very boring and irrelevant in my opinion as a viewer, long uninteresting videos just because you do it once a week.. goodluck but I’m out sorry.
This is quite interesting actually. Especially long term. But you obviously only like action videos which I find a bit boring.
Can’t please everyone I guess. Thanks for the comment though. Unfortunately I don’t have huge budgets so I do what I can.
I’m sorry it was wrong of me to say, I was just being irrational. I guess I just wanted more than a tool video, but that’s me. I’m sure it helps a lot of people it to me just won’t help my situation. But again it’s for a broader community not just myself so again, I’m sorry. I will continue to watch
I used to add a new tool to the box every 2 weeks when I was building up my box.
The snap on truck has gotten me many times
@@BennysCustomWorks Oh yeah, I put that guy's kid through school, lol.