Yale is not happy to help the guys with older system, they want to to buy a new one... There are 3 sequenses to add a keypad, based on your system, for HSA3800 is : 1 Press the ‘A’ key (left red button at the top of the keypad) followed by factory default keypad code ‘0000’. 2 The LED will now flash slowly indicating it is in test (programming) mode. 3 Press the ‘A’ key followed by the ‘7’ key to set the keypad into PIN code mode. 4 Press the ‘B’ key ((right red button at the top of the keypad) and enter new four digit keypad code followed by the Arm key. 5 Quit test mode by pressing the disarm key twice. The keypad code and mode setting has been completed. • The keypad code is not used by the system, only the keypad itself. You should not have to use this code again so make a note of it and keep it in a safe, secure place. Then : 6. While in add device mode in Control Panel (when asking to press the button on the device you want to add ) 7. Press A key followed by 0000 or whatever code you inputted on your keypad (see step 4) 8. Press A key followed by the 8 9. Press A key followed by the 2 (the control panel will beep once to aknowledge pairing) 10. Press the disarm key twice. The Keypad code and mode setting has been completed. The Keypad will now use the same PIN code that is set for the Control Panel. For other models : Key Pad initialisation If you purchase a Key Pad as an accessory, you will need to initialise it prior to use with the Control Panel. 7. Press A key followed by 0000 or whatever code you inputted on your keypad (see step 4) 8. Press A key followed by the 7 The LED will now flash slowly indicating it is in test (programming) mode. 9. Press A key followed by the 1 (the control panel will beep once to aknowledge pairing) 10. Press the disarm key twice. The Keypad code and mode setting has been completed. The Keypad will now use the same PIN code that is set for the Control Panel. If the keypad it doesnt disarm... Please remove the keypad from the system then complete the following procedure: 1. Press the ‘Panic button A’ key followed by factory default Key Pad code ‘0000’ (this is different to your Control Panel PIN code). 2. The LED will now flash slowly indicating it is in test (programming) mode. 3. Press the ‘Panic button A’ key followed by the ‘7’ key to set the Key Pad into Control Panel system mode (also known as slave mode). 4. Quit test mode by pressing the disarm key twice. The Key Pad code and mode setting has been completed. The Key Pad will now use the same PIN code that is set for the Control Panel To learn in a keypad, press 8 and 9 together until you hear a beep. Other option for newer models : Please remove the keypad from the system then complete the following procedure: 1. Press the ‘Panic button A’ key followed by factory default Key Pad code ‘0000’ (this is different to your Control Panel PIN code). The LED will now flash slowly indicating it is in test (programming) mode. 2. Press the ‘Panic button A’ key followed by the ‘7’ key to set the Key Pad into Control Panel system mode (also known as secondary mode). 3. The LED will now flash slowly indicating it is in test (programming) mode. 4. Press the ‘Panic button A’ key followed by the ‘7’ key to set the Key Pad into Control Panel system 5. Quit test mode by pressing the disarm key twice. The Key Pad code and mode setting has been completed. The KeyPad will now use the same PIN code that is set for the Control Panel. To learn in a keypad, press 8 and 9 together until you hear a beep. Hope this will help you guys, not sure which one it will work for you, it took me almost a day to find these...the first sequesce it was the hardest to find...
you prolly dont care but if you're stoned like me atm you can watch all the new movies on InstaFlixxer. I've been watching with my brother during the lockdown :)
Yale is not happy to help the guys with older system, they want to to buy a new one...
There are 3 sequenses to add a keypad, based on your system, for HSA3800 is :
1 Press the ‘A’ key (left red button at the top of the keypad) followed by factory default keypad code ‘0000’.
2 The LED will now flash slowly indicating it is in test (programming) mode.
3 Press the ‘A’ key followed by the ‘7’ key to set the keypad into PIN code mode.
4 Press the ‘B’ key ((right red button at the top of the keypad) and enter new four digit keypad code followed by the Arm key.
5 Quit test mode by pressing the disarm key twice. The keypad code and mode setting has been completed.
• The keypad code is not used by the system, only the keypad itself. You should not have to use this code again so make a note of it and keep it in a safe, secure place.
Then :
6. While in add device mode in Control Panel (when asking to press the button on the device you want to add )
7. Press A key followed by 0000 or whatever code you inputted on your keypad (see step 4)
8. Press A key followed by the 8
9. Press A key followed by the 2 (the control panel will beep once to aknowledge pairing)
10. Press the disarm key twice.
The Keypad code and mode setting has been completed.
The Keypad will now use the same PIN code that is set for the Control Panel.
For other models :
Key Pad initialisation
If you purchase a Key Pad as an accessory, you
will need to initialise it prior to use with the Control
Panel.
7. Press A key followed by 0000 or whatever code you inputted on your keypad (see step 4)
8. Press A key followed by the 7
The LED will now flash slowly indicating it is in test
(programming) mode.
9. Press A key followed by the 1 (the control panel will beep once to aknowledge pairing)
10. Press the disarm key twice.
The Keypad code and mode setting has been completed.
The Keypad will now use the same PIN code that is set for the Control Panel.
If the keypad it doesnt disarm...
Please remove the keypad from the system then complete the following procedure:
1. Press the ‘Panic button A’ key followed by factory
default Key Pad code ‘0000’ (this is different to
your Control Panel PIN code).
2. The LED will now flash slowly indicating it is in test
(programming) mode.
3. Press the ‘Panic button A’ key followed by the ‘7’
key to set the Key Pad into Control Panel system
mode (also known as slave mode).
4. Quit test mode by pressing the disarm key twice.
The Key Pad code and mode setting has been
completed. The Key Pad will now use the same
PIN code that is set for the Control Panel
To learn in a keypad, press 8 and 9 together until you hear a beep.
Other option for newer models :
Please remove the keypad from the system then complete the following procedure:
1. Press the ‘Panic button A’ key followed by factory default Key Pad code ‘0000’ (this is different to your Control Panel PIN code).
The LED will now flash slowly indicating it is in test
(programming) mode.
2. Press the ‘Panic button A’ key followed by the ‘7’ key to set the Key Pad into Control Panel system mode (also known as secondary mode).
3. The LED will now flash slowly indicating it is in test (programming) mode.
4. Press the ‘Panic button A’ key followed by the ‘7’ key to set the Key Pad into Control Panel system
5. Quit test mode by pressing the disarm key twice. The Key Pad code and mode setting has been completed. The KeyPad will now use the same PIN code that is set for the Control Panel.
To learn in a keypad, press 8 and 9 together until you hear a beep.
Hope this will help you guys, not sure which one it will work for you, it took me almost a day to find these...the first sequesce it was the hardest to find...
I found to program grey key pad press 8 and 9 together this learns it into the system this is not in the instructions ??
Can I part arm/ disarm the system?
My standard Yale pir just beeps once but does not active my alarm
Wow
Hi can pls let me know how to program an extra keyfob
Master gamers Creeperxx5 ,use the same steps if not working ask Yale
It's in the book see program list
you prolly dont care but if you're stoned like me atm you can watch all the new movies on InstaFlixxer. I've been watching with my brother during the lockdown :)
@Kash Wells yea, I've been using Instaflixxer for months myself :D