I don’t have any of your big bore engines currently however will be ordering the small bore immediately upon release. I really do enjoy watching your info videos even though I don’t have these engines. You really put a lot of time and effort into helping everyone having a good experience with your products. Excellent business model in my opinion. Makes me want to do more business with your company in the future!
Another tip if flooded you can remove the fuel line from the carb to use up the fuel in the carb/Reed, thus clearing out a flooded motor really easily:)
I assume this means you dont have the WJ carb, which is ok, some older ones might have a WT version, if no choke then i bet its a Rooster 990 Full mod, so just a crack of throttle and go for it, cna choke by hand if want for one pull by blocking the air intake during the pull
@@TAYLORRC thank u Mike and it Cjay .. brought the linkage and the pull start today and could u give me email tomorrow for that wj carb plz I will order it and thank u again
I currently have the new WJ 14 carburetor on my new Taylor 46GT engine and it starts up but it cut off when I stop pulling the throttle brand new to this 1/5 scale gas RC.
@TAYLORRC oh ok wonderful appreciate you for the information. Looking forward in breaking-in before winter snd have ready for next warm season. 1-tank rich and after that tune for optimum performance?
the 30N truck is pretty tough, not too much to do, you will need these oversize Billet housings or you'll melt the stock ones and bearings let go etc (ideally pick the discount towers too as give adjustment for big bore ride height, www.taylorrc.co.uk/product-page/losi-5t-5b-diff-housing-set Further to upgrade the centre diff, youll need this sweet kit:www.taylorrc.co.uk/product-page/modified-rc-centre-diff-mount
Can you do a carb tuning video please adjusting HSN & LSN for optimum performance please
I don’t have any of your big bore engines currently however will be ordering the small bore immediately upon release. I really do enjoy watching your info videos even though I don’t have these engines. You really put a lot of time and effort into helping everyone having a good experience with your products. Excellent business model in my opinion. Makes me want to do more business with your company in the future!
Great vid, next start will be easy!!
awsome vid great to see these for guys buying a wj carb for the first time
So this only works on wj carb?
This video is what I been looking for with the WJ71 on my Losi 5t with a Bartolone 40...Thanks Mike
I really appreciate the video man! Some day! Some day I’ll have a 71😊
Brilliant information great video
Great informative video Mike👊🏻👍 definitely will be helpful
Helped a ton, thank you
Great video Mike 👍🏼 awesome information😎 I cannot believe how easy that thing started after you flooded it lol 😂 great video bro 😉
Awesome informational video mike, you should keep up videos even if its driving your own rc’s keep up the good work 💨👊🏻
Another tip if flooded you can remove the fuel line from the carb to use up the fuel in the carb/Reed, thus clearing out a flooded motor really easily:)
Hi Mike .. on the 50gt on the carb there is no choke where u said on its ..so do I open up the throttle little bit then start it ?
I assume this means you dont have the WJ carb, which is ok, some older ones might have a WT version, if no choke then i bet its a Rooster 990 Full mod, so just a crack of throttle and go for it, cna choke by hand if want for one pull by blocking the air intake during the pull
@@TAYLORRC thank u Mike and it Cjay .. brought the linkage and the pull start today and could u give me email tomorrow for that wj carb plz I will order it and thank u again
Can we get the head on the idle screw changed to a head like the needles so u don’t have to use pliers to turn it 🙄
@@The.Toaster yeah I know that
Walbro makes the carbs
But mike Taylor and alx could ask for the different screw head
About time someone made this video about the WJ71 carb. Also have the Bartolone 40cc. Losi 5T..
I currently have the new WJ 14 carburetor on my new Taylor 46GT engine and it starts up but it cut off when I stop pulling the throttle brand new to this 1/5 scale gas RC.
And i have not touched any of the settings on the low or high ect.
It's the WJ146 carburetor
Do you still sell them tires can find them on dp site
Sure! www.taylorrc.co.uk/genesis-foam-less-wheels-1
What motors do you have that will fit that new losi dbxl 2.0?
What temperatures should I be looking, for operation and not to go over?
measured on top of the head near plug shoot for 180C bashing temps and dont go over 200C, but you wont do that as long as you are correct on tune.
@TAYLORRC oh ok wonderful appreciate you for the information. Looking forward in breaking-in before winter snd have ready for next warm season. 1-tank rich and after that tune for optimum performance?
nice !!!
Do you have to do any modifications to the 30° North? I want to put a 65 supreme in it.
the 30N truck is pretty tough, not too much to do, you will need these oversize Billet housings or you'll melt the stock ones and bearings let go etc (ideally pick the discount towers too as give adjustment for big bore ride height, www.taylorrc.co.uk/product-page/losi-5t-5b-diff-housing-set Further to upgrade the centre diff, youll need this sweet kit:www.taylorrc.co.uk/product-page/modified-rc-centre-diff-mount
@@TAYLORRC Okay, thank you. I will be purchasing my 65 supreme this Friday.
Sorry one more question on adjusting my ride height. Do I adjust up or down?
@@d_o_u_g_h_b_o_yg_o_t_t_i3640 yeah lift car up a bit so it compensates, just need a shock tower with extra hole positions to adjust
Lindo carro
good god man you are long winded
What is this fuel tank from?