You are on 🔥 with the uploads lately! Nice work. Whenever I do a fuel filter or with these pumps I would crack the fuel bleed screw at the outlet of the fuel filter and then pump the primer until fuel bleeds out. Cheers 🍻
Great videos. Got my first, first gen. A 1992 d350 dually flatbed. I've watched and done pretty much every engine upgrade you've shown, the fuel spring, pin, turbo intercooler pipes, eagle eye exhaust, piston lift pump, ect. I was able to max my fuel pump all the way out. But your videos make it super easy to follow step by step. I've recommended your channel to friends with first gens. Keep up the great work
Did this a few weeks ago…if you don’t tighten the banjo bolt before you prime the pump then you definitely don’t have to bleed the injectors. Keep up the good work!
If you purchase 2 studs and nuts to replace the mounting bolts …install them into the block first then slip everything onto them…you will not fight lining up bolts into holes. 8x1.25 metric thread I believe by 1 1/2”-2”long.
Thanks for a well explained and inspirational video. I hoped id had my 1st Gen by now by i know the time will come and find one at my budget price. The 12 valve diesel engine roar brings back my childhood. My dad used to be a driver since age 7 or 8. Driver all his life. So he enjoy engines like CUMMINS PERKINS INTERNATIONAL all in the old country of Mexico.
I never wanted to cut the insulation...so i manged to carefully bend the hardline enough not to kink it ...just enough to clear the side of the block .
Another awesome vid Tim. My W350's gonna be getting this next, so far she's got 4" turbo back exhaust, THD fuel pin and 3200 gov spring. Bigger intake tubbing and this HVLP lift pumps next! keeper coming man...love the content!
how do i know if my lift pump is bad ? had my injection pump and injectors rebuild and replaced going on two years but my truck has a rough idle i was told it could be my lift pump
The benefit comes when you start getting above stock horse power. The stock fuel pump can maintain sufficient fuel pressure at stock settings. Once you start tweaking things and tuning it can't maintain good fuel pressure. The HVLP can maintain the fuel pressure. I'm at 500 hp and it still has fuel pressure at full throttle pulls.
Whenever you do this changing one of those pumps I don’t care if you put in a factory stock one on a hungry diesel high-volume pump which I think is a good way to go always take your number one cylinder valve cover off and make sure the intake and exhaust valves are closed somewhere near top dead center on the number one cylinder cam load the drives the pump will be on the other side so to speak and you’ll be able to put it in there you won’t have to trade her push up against a cam lobe this is six in a row jim From Kennerdell a Pennsylvania a
Did you have to get another adapter i tried installing the pump today but the fitting from the old pump had no spot to thread to the hole there was much bigger
Some say they can feel an hp difference but the big benefit is that this will support fuel for higher HP. I'm at 500 go with this pump which the stock pump could NEVER do.
@@decentgarage Didn't go smooth as yours, couple things that helped me was instead of using a knife, I used a long gasket scraper and rubber mallet to cut/peel the plastic/insulation away. Also, leaving the pump a bit loose and installing the hardline helped alot too. Appreciate you making the video, voted for your truck on 1st Gen Cummins too!
Can you use your influence to get the lift pump company to pre bend the tube so that it goes right on a 1st. gen. W/O cutting into the head insulator, I drive a lot in very cold temps need that to keep engine head warm?
When you do that job is long as you have a decent valve cover gasket on your engine take the number one cylinder off the gasket or excuse me the valve cover and make sure when you roll the engine over to where the intake and exhaust valve are closed somewhere near top dead center don’t have to be perfect that way the camo you’re not fight in the camo trying to put the pump on it’s it’s a lot easier that way this is six in a row Jim From Kennerdell a Pennsylvania
Love your videos! Could you explain what is the purpose of the high volume pump on a not modified or lightly modified truck (which I assume this one is)? Are there situations where the low volume pump cant keep up with the needs of the injection pump? Thanks!
The stock pumps can do fine especially if the truck is stock. I do know people running 450 hp on a stock lift pump. But, the hvlp does a much better job of maintain sufficient fuel pressure under load and is much more reliable.
One advantage of the HVLP pump is the ability to prime the system without having to get the cam in the right position first like is required with the stock pump. Just push the plunger in no matter what position the cam is in. And from what I've read (someone correct me if this isn't right), it provides somewhere in the neighborhood of 10 to 15 PSI to the injection pump. My stock lift pump provides 5 to 7 psi at idle, less at speed.
Would you recommend this fuel pump or a factory style pump for a stock application? I have plans to upgrade the fuel pin and governor spring in the future but that could be a while away, since I have some things planned before this.
This pump will work from stock all the way up to 600 hp. The hungry diesel is having a sale this month too. 15% off everything using promo code August22
Great video! I’ve been waiting on this video before I do this install on my D350! Couldn’t really tell, but they make a fuel rated PTFE Teflon tape which is yellow in color, I’ll be using permatex PTFE thread sealant instead to avoid dealing with possible tape removal or pieces of tape flaking off in the future. I’ve read there is a torque spec for the mounting bolts. I’ll let you know how it turns out!
Mark that's an interesting point. I've got the yellow tape but i was under the impression that it was for natural gas purposes. I just used normal Teflon tape. Luckily the fuel filter is the next thing in line so any flecks of tape that would come off would get caught there 🤷♂️
I did this today. What an absolute miserable pain in the dick! Your video makes it look like there is loads of clearance and everything is right in the open! Well.... no. Intercooler tube, master cylinder, brake booster, brake lines, hood hinge... all that crap in the way. And that insulation was made of cast iron. I had to get a serrated blade and saw at it to get it to cut, and even that was nearly impossible. I wanted to get the sawzall out, but no room. Finally did get it. To anybody doing this, prepare for about 4-5 hours of labor, and you will neologize some new profanity. A stool will help greatly. The bolt on the firewall side of the pump is nearly impossible to get to. I had to cobble together 3 extensions and use my cordless ratchet to keep the bolt spinning while I wiggled the pump around with my left hand... after I dislocated my shoulder so I could do that. Not the ideal way to start a bolt, but it was the only way I could see to get it started. Thank god for cordless ratchets. Oh, and use some masking tape on the top and bottom of the gasket/spacer sandwich to keep it from falling off into the abyss when you put the pump on. Just remember to peel it off once you finally get the bolts started. As stated in the video text overlay, you DEFINITELY want to install the pump with the hard fuel line in place, but loose so you can adjust it. On my pump (Genuine Cummins part), the hard line did not quite line up with the hole for the banjo bolt. It was off by a fraction of a MM, just enough to make it a PITA. In order to get a socket (17mm) on this, you'll have to un-snap the plastic clip that holds the throttle cable onto the metal bracket. The bolt is very short, so you will need to put a few of those really tiny thin rubber bands inside your socket, and top that with a washer to make a super shallow. That will allow you to keep pressure on the bolt while you turn it with one hand (use a driver, not a ratchet) and hold the line in place with the other. I tried with a wrench and a un-modified socket, and the bolt just would not start. Back washer kept coming out and falling down into the floor (thankfully onto the floor and not lost in the engine bay somewhere) because the wrench and socket both allowed the bolt to slide too far back. Forget starting it by hand. Won't go. But now I have 17 PSI of fuel pressure at idle. More than claimed. Dangerously high for a stock VE pump. The max inlet pressure for these injection pumps is 18 PSI. And that was 30 years ago when they were new. Be prepared to repair your injection pump soon with this lift pump.
You are on 🔥 with the uploads lately! Nice work. Whenever I do a fuel filter or with these pumps I would crack the fuel bleed screw at the outlet of the fuel filter and then pump the primer until fuel bleeds out. Cheers 🍻
Well now I know! I'll do that from here on out for sure!
Two of the best working together!!!
Great videos. Got my first, first gen. A 1992 d350 dually flatbed. I've watched and done pretty much every engine upgrade you've shown, the fuel spring, pin, turbo intercooler pipes, eagle eye exhaust, piston lift pump, ect. I was able to max my fuel pump all the way out. But your videos make it super easy to follow step by step. I've recommended your channel to friends with first gens. Keep up the great work
Thanks for the discount code man, just ordered the lift pump can’t wait to install it.
Did this a few weeks ago…if you don’t tighten the banjo bolt before you prime the pump then you definitely don’t have to bleed the injectors. Keep up the good work!
Good tip!
If you purchase 2 studs and nuts to replace the mounting bolts …install them into the block first then slip everything onto them…you will not fight lining up bolts into holes. 8x1.25 metric thread I believe by 1 1/2”-2”long.
Genius idea! I will be doing that in the future for sure!
Thanks for a well explained and inspirational video. I hoped id had my 1st Gen by now by i know the time will come and find one at my budget price. The 12 valve diesel engine roar brings back my childhood. My dad used to be a driver since age 7 or 8. Driver all his life. So he enjoy engines like CUMMINS PERKINS INTERNATIONAL all in the old country of Mexico.
You'll find one!
How would you know if you need to bleed the injectors?
If you try to start it and it cranks and cranks and cranks you need to bleed the injectors
I never wanted to cut the insulation...so i manged to carefully bend the hardline enough not to kink it ...just enough to clear the side of the block .
Another awesome vid Tim. My W350's gonna be getting this next, so far she's got 4" turbo back exhaust, THD fuel pin and 3200 gov spring. Bigger intake tubbing and this HVLP lift pumps next! keeper coming man...love the content!
Nice! I'll have a video on the intake tubing coming out shortly
how do i know if my lift pump
is bad ? had my injection pump and injectors rebuild and replaced going on two years but my truck has a rough idle i was told it could be my lift pump
Do you have a fuel pressure gauge? That is what you need.
Tim did you temporarily move the battery cable to get the new pump in? Didn't see it happen.
I did not have to move the battery cable
Great install information.
One thing what benefits do you get with this type of pump? I'm doing a 4BT swap to my Nissan Patrol Y61. Thanks
The benefit comes when you start getting above stock horse power. The stock fuel pump can maintain sufficient fuel pressure at stock settings. Once you start tweaking things and tuning it can't maintain good fuel pressure. The HVLP can maintain the fuel pressure. I'm at 500 hp and it still has fuel pressure at full throttle pulls.
Is there an inlet screen on the new pump ?
Yes, there should be an inlet screen.
Whenever you do this changing one of those pumps I don’t care if you put in a factory stock one on a hungry diesel high-volume pump which I think is a good way to go always take your number one cylinder valve cover off and make sure the intake and exhaust valves are closed somewhere near top dead center on the number one cylinder cam load the drives the pump will be on the other side so to speak and you’ll be able to put it in there you won’t have to trade her push up against a cam lobe this is six in a row jim From Kennerdell a Pennsylvania a
Good tip 👍
Excellent tutorial video. 🙂👍
Great job man! 💯 Thank you! 🤝
No problem 👍
Did you have to get another adapter i tried installing the pump today but the fitting from the old pump had no spot to thread to the hole there was much bigger
Mine have all hooked right up
Does installing this pump increases a good amount of hp?
Some say they can feel an hp difference but the big benefit is that this will support fuel for higher HP. I'm at 500 go with this pump which the stock pump could NEVER do.
Getting ready to do this myself. Thank you for posting this.
Let us know how it goes!
@@decentgarage Didn't go smooth as yours, couple things that helped me was instead of using a knife, I used a long gasket scraper and rubber mallet to cut/peel the plastic/insulation away. Also, leaving the pump a bit loose and installing the hardline helped alot too. Appreciate you making the video, voted for your truck on 1st Gen Cummins too!
@@Ironwind1972 this was not my first time doing it. Every time you do it it will get easier. Did you notice any difference?
Can you use your influence to get the lift pump company to pre bend the tube so that it goes right on a 1st. gen. W/O cutting into the head insulator, I drive a lot in very cold temps need that to keep engine head warm?
When you do that job is long as you have a decent valve cover gasket on your engine take the number one cylinder off the gasket or excuse me the valve cover and make sure when you roll the engine over to where the intake and exhaust valve are closed somewhere near top dead center don’t have to be perfect that way the camo you’re not fight in the camo trying to put the pump on it’s it’s a lot easier that way this is six in a row Jim From Kennerdell a Pennsylvania
That's a great idea!
Do you have to buy the new hose?
No it comes with the new fuel line
Love your videos! Could you explain what is the purpose of the high volume pump on a not modified or lightly modified truck (which I assume this one is)? Are there situations where the low volume pump cant keep up with the needs of the injection pump? Thanks!
The stock pumps can do fine especially if the truck is stock. I do know people running 450 hp on a stock lift pump. But, the hvlp does a much better job of maintain sufficient fuel pressure under load and is much more reliable.
@@decentgarage Thanks for the reply! Thats what I thought. I'll keep the stock one until it dies and then replace with HVLP!
@@polakmaciej1547 not a bad plan. Or just wait till you see a good THD sale on them. I've seen him do sales on these for $150
One advantage of the HVLP pump is the ability to prime the system without having to get the cam in the right position first like is required with the stock pump. Just push the plunger in no matter what position the cam is in. And from what I've read (someone correct me if this isn't right), it provides somewhere in the neighborhood of 10 to 15 PSI to the injection pump. My stock lift pump provides 5 to 7 psi at idle, less at speed.
@@garylewis327 everything you said is exactly right. Mine provides between 12-16 psi.
Dude great video but you should Be using Yellow fuel rated Teflon tape!
Another nice video, Tim. Good job. This mod is on my list.
Thanks Maynard!
So do you gain some more power out of this?
No, it's just a way to ensure you maintain proper fuel psi as you do additional fueling mods
@@decentgarage gotcha. Just ordered mine from thd, as well as my exhaust. Used your discount code also!
@@ericpatton7767 Awesome!
What does the new pump do exactly?
Slightly more PSI and more consistent PSI under load.
Great video man 🤘
Thanks Devin!
Would you recommend this fuel pump or a factory style pump for a stock application? I have plans to upgrade the fuel pin and governor spring in the future but that could be a while away, since I have some things planned before this.
The reason I’m asking is my pump is leaking not bad but it is leaking some
This pump will work from stock all the way up to 600 hp. The hungry diesel is having a sale this month too. 15% off everything using promo code August22
does anyone know how much power that these pumps can support?
The VE HP record truck had this pump on it so you should be good for anything the VE can do.
Great video! I’ve been waiting on this video before I do this install on my D350! Couldn’t really tell, but they make a fuel rated PTFE Teflon tape which is yellow in color, I’ll be using permatex PTFE thread sealant instead to avoid dealing with possible tape removal or pieces of tape flaking off in the future. I’ve read there is a torque spec for the mounting bolts. I’ll let you know how it turns out!
Mark that's an interesting point. I've got the yellow tape but i was under the impression that it was for natural gas purposes. I just used normal Teflon tape. Luckily the fuel filter is the next thing in line so any flecks of tape that would come off would get caught there 🤷♂️
Great video! 👏
Thanks!
Ohhh that’s very cool y’all have a little crew well shoot you have a crew by yourself lol
So what if the piece you cut with a box cutter is metal 😅
Not metal , just really hard rubber , pain in ass too cut 😅
😎👍 eres un buen mecánico amigo
I did this today. What an absolute miserable pain in the dick! Your video makes it look like there is loads of clearance and everything is right in the open! Well.... no. Intercooler tube, master cylinder, brake booster, brake lines, hood hinge... all that crap in the way. And that insulation was made of cast iron. I had to get a serrated blade and saw at it to get it to cut, and even that was nearly impossible. I wanted to get the sawzall out, but no room. Finally did get it. To anybody doing this, prepare for about 4-5 hours of labor, and you will neologize some new profanity. A stool will help greatly. The bolt on the firewall side of the pump is nearly impossible to get to. I had to cobble together 3 extensions and use my cordless ratchet to keep the bolt spinning while I wiggled the pump around with my left hand... after I dislocated my shoulder so I could do that. Not the ideal way to start a bolt, but it was the only way I could see to get it started. Thank god for cordless ratchets. Oh, and use some masking tape on the top and bottom of the gasket/spacer sandwich to keep it from falling off into the abyss when you put the pump on. Just remember to peel it off once you finally get the bolts started. As stated in the video text overlay, you DEFINITELY want to install the pump with the hard fuel line in place, but loose so you can adjust it. On my pump (Genuine Cummins part), the hard line did not quite line up with the hole for the banjo bolt. It was off by a fraction of a MM, just enough to make it a PITA. In order to get a socket (17mm) on this, you'll have to un-snap the plastic clip that holds the throttle cable onto the metal bracket. The bolt is very short, so you will need to put a few of those really tiny thin rubber bands inside your socket, and top that with a washer to make a super shallow. That will allow you to keep pressure on the bolt while you turn it with one hand (use a driver, not a ratchet) and hold the line in place with the other. I tried with a wrench and a un-modified socket, and the bolt just would not start. Back washer kept coming out and falling down into the floor (thankfully onto the floor and not lost in the engine bay somewhere) because the wrench and socket both allowed the bolt to slide too far back. Forget starting it by hand. Won't go. But now I have 17 PSI of fuel pressure at idle. More than claimed. Dangerously high for a stock VE pump. The max inlet pressure for these injection pumps is 18 PSI. And that was 30 years ago when they were new. Be prepared to repair your injection pump soon with this lift pump.
😎🇺🇸🍺
Thanks Peter!