Thanks for the video. I used this to replace my charge port. For anyone who needs to do the same there is one more screw to remove on the middle frame shown at 3:46. It's the one in the middle by the camera that is covered by an orange sticker.
Just want to say thanks, and to warn others, for pointing out that you need to be careful taking the back cover off around the power and volume buttons because that gold finger print ribbon WILL get ripped. I watched another video when I was trying to fix my smashed camera lense and the other video gave absolutely no warning about this ridiculously exposed and stupidly positioned gold ribbon, hence my camera lense replacement turned into a fingerprint sensor replacement, hence how I found this video. Ironically, the video I watched for the camera lense replacement wasn't even for the Note 10 PRO, it was for the Note 10, and for the Note 10 Pro, you don't even need to remove the back off the phone to replace the camera lense, so I ended up severing the fingerprint sensor for no reason. The back is fairly hard to get off and this ribbon is right where you drag your tool around the edge so it's almost inevitable you'll butcher it - my advice is to leave that but til last, and go around all the other edges, then pull that last bit apart manually and gently. In terms of the fingerprint sensor, what a horrible job. This video is brilliant but also doesn't show how hard it is to get an entry point for getting the middle casing off, which I found to be really difficult and I was waiting for a screen smash tbh. Furthermore, I don't know why, but my middle casing wouldn't come off entirety. Something was causing it to be stuck down to the right hand side of the camera so although all the edges were free, it wouldn't pull off due to being stuck by something in the top middle (yes, all screws were removed). I really tried to remove it but it snapped the plastic at the top between what looks like the speaker holes. So something important was obviously holding it down and I didn't fancy totalling my whole phone so I tried to fit the fingerprint sensor by leaving the middle casing on and pulling it up. This took 3 hours of continuous trial and error, and took years off my life. This thing needs full access and even then, it looked pretty fiddly in the video, so multiply that roughly by 4 million and you've got an idea how near impossible this was was the middle casing still attached. By some miracle, I got the button in, so I taped it in to it's hole to keep it secure and got to work on pushing its miniscule holding clips (one of which has the offending gold ribbon with it, more opportunities to mangle it again!) behind the miniscule plastic housing. A toothpick and tweezers and The Lord are essential. Next job, getting the chip into it's housing. Hahaha, its housing is underneath the part that needs to come off with the middle, which is the part which seems to be stuck down by something immovable. Basically it's like threading a needle and sewing a button in the dark. You manage to lift it by about 5mm and hit and hope for a couple of hours before you all of a sudden feel a small click and freeze in fear of budging it off again with your hands which have now been trembling for half a day of your life. Retreat at the speed of a snail and.reconstruct. Tldr; the camera lense can be replaced easily and without removing the back cover. If you remove the back cover for any reason, you almost certainly will cut the finger print sensor. The middle casing doesn't come off.
You are an amazing writer. The "middle case" passage onward, it is hard to fathom for me. I ordered the 108MP main Quad lens. Before DIY, I will read your post again. if you find out a video that does the job 'carefully', that would help to understand your post better
@@jparkhku @Jay P if you have this exact model of phone (the PRO version) you do not need to remove the back cover or the middle cover to replace the rear camera lense cover. You simply need to get something sharp in one of the corners (smash one if you need to, it'll make it easier) grab the "glass" at that corner point with some tweezers and pull upwards slowly. This will pull the entire lense casing off - it is simply stuck down with glue, no screws. Clean what is left, use a bit of sticky tape to dab around the lense to ensure you remove all the tiny fragments (if applicable) and stick your new lense cover down in the outline of the old one, as you would with a screen protector, it's exactly the same process. Be careful of fingerprints on the glass. As I said, that's how to replace the lens casing on the Redmi Note 10 PRO version only - others models are different
@@jparkhku if you're replacing the actual lense/camera, that's much harder and you definitely need to source videos for this specifically and not just a tear down video of the phone. As I mentioned previously, this video doesn't show something to the right of the rear camera which is secured tightly and won't allow you to remove the middle casing. I presume it's a screw but I couldn't see it and didn't want to start taking things apart that weren't shown on the video.
@@laurat7485 Yes, my problem is a badly scratched main lens itself (108MP). My spare part is about to arrive but I am now doubting if this is really a DIY. Do you think that the first 4:30 of this video will do? ua-cam.com/video/qliO18uGrcA/v-deo.html I think I will manage to dodge the accident of ripping off the fingertip sensor flex connector.
Amazing and very nicely opened, Please tell me I didn't find where ia liquid cooling in this phone as I have seen in POCO phones there's liquid coper pipe in the phone, is this phone Trustable for not getting heat up.
Does the sound of something loose when you tap the camera with your finger or put the phone vigorously on the table indicates a damaged phone or is it something from the stabilization of the camera and it should be so?
Keeping an eye on recent Xiomi trend of withdrawing special and unique MIUI features like Second Space, I request UA-camrs to please highlight such withdrawal in their reviews of Xiomi mobiles like Mi, Redmi and POCO to help viewers take an informed decision.
If we see it from business view, second space is very good for us but bad for company. Just imagine with it we can act as if we have 2 phones. Not only that miui have dual apps function. So technically you can have 4 same apps on a single phone.
Sir can u please this phone speaker teardown how it is in side in main speaker and i have a question for you that if the covering of thin cloth is teared does that effect the sound quality plzz 🙏🙏🙏 answer to this question
after contact with sea water it does not work. Can I use a motherboard antioxidant or isopropyl alcohol cleaning with ultrasound? thanks and congratulations
Since you may have opened various brand of smartphones which one you think have done great job in case of hardware like number of switches for many things to connect and reconnect easily or removed easily, hardware durability, simple pattern to adjust many things in small area inside a board etc...
and that sucks as screens turn on and off so randomly while on call. and after using power button to switch on and off screen while call also sucks due to this
@@amankumardubey That is the most annoying thing about this phone screen turn off when listening to a whatsapp Audio bad sensor inside this trash device
@@shijugopinath5647 Its nice phone. Just my concern is gets warm when on charging. I switch off to charge. Im thinking to use smaller plug instead of 33W. I got 25W samsung plug maybe i try like this. For the rest its all so far so good
I have the global version with 104mp camera. I get a lot of rattling vibration from the camera area if you tap the back or put it down on a hard surface. Do you think this is OIS ?? I thought it only had digital stabilization but looking at you video it looks like optical on the 64mp version. Does yours make noise from the camera area?? Great video 😃
i too have that rattling vibration when tapped or placed on surface ...... it is because the phone has an inbuilt micro gimbal to stabilize video ..so that might have caused the rattling//
@@someoneeternal7575 BS. No it doesn not have any sort of OIS or Gimbal. Its just the housing of the LEns it needs more area to move for focusing. Thats all. When u take a video with Stabilization it will crop the video a lot for EIS. If it had OIS it wouldnt crop it too much. And when taking night shots it will come shaky af. U need a tripod to take night shots.
Bhai meri nye phone k redmi note 10pro ki trey fas gyi hai ab Bo niklati hi nhi hai bhoot koshish ki sb ne to ab mai kya kru mi service care k pass jau kya
FYI: the easiest way to disconnect the frame is to start under the SIM card tray, there just a thin plastic piece that can be easily bent away of the frame.
Bhai aapko redmi note 10 pro mein Kya Kya problem face ho rahi Hain Kya Kya bugs dekhne ko mile Hain please batao bhai mujhe Bhai Lena hai Kya le Sakta hoon please help
Bro, 1 question, why does your Redmi Note 10 pro have OIS in the main Camera ? I read in spec sheet that the Redmi Note 10 pro don't support OIS on the Main Camera.
@•Itz_Justin• Note 10 pro indian version with 64mp Note 10 pro max indian version 108mp HM2 samsung sensor Global there is:note 10 pro with HM2 samsung 108mp sensor. All phones got same characteristics... The global note 10 pro and the indian version note 10 pro max is the ones with same samsung 108 camera
Bhai mera redmi Note 10 Pro mex me battery charge ka imoji Dekha raha hai But charge store Nahin ho raha hai kya karne se tik hogaa bhai please bataiye😢😢
Phone bhaut badiya hai agar ap ke room ka temperature 25-35 tak hai battery draining ki koi problem nahi ayi gamming me bhi bas temperature shai ho aur lag hai camera mast hai
Video watching from 10pro 😂😂😂
සැහිමකට පත් වේන්න පුලුවන්ද 😉😉😂
Bro how is your experience in 10 pro
Heat problem battery drain and performance
kaisa phone hai bhai muze bhi lena hai
@@stststststst819ha yaar please batao
🤣🤣🤣
Watching on note 10 pro..
Max me
Yes me also...
Iam also
Same
Lol same
The battery pull tab is awesome
Underrated
Thanks for the video. I used this to replace my charge port. For anyone who needs to do the same there is one more screw to remove on the middle frame shown at 3:46. It's the one in the middle by the camera that is covered by an orange sticker.
whats the story with the charging port bro😢even mine is damaged!!
No words to say... Well done dear... Thanks
Thank You..
I wish I had so steady hands :) Thanks for the video, really helpful!
Hi..Thanks for comment . Your Positive Comments Help us Create More Videos..SUBSCRIBE our Channel and SHARE on FB ....Support us....
Total video is outstanding . You are really great teacher and also great technician.
😂Just bought redmi note 10...❤half an hour ago.. And login to Google account.. After this is my first video😁
🤣🤣🤣🤣
really detailed really good, thank you so much
Just want to say thanks, and to warn others, for pointing out that you need to be careful taking the back cover off around the power and volume buttons because that gold finger print ribbon WILL get ripped. I watched another video when I was trying to fix my smashed camera lense and the other video gave absolutely no warning about this ridiculously exposed and stupidly positioned gold ribbon, hence my camera lense replacement turned into a fingerprint sensor replacement, hence how I found this video. Ironically, the video I watched for the camera lense replacement wasn't even for the Note 10 PRO, it was for the Note 10, and for the Note 10 Pro, you don't even need to remove the back off the phone to replace the camera lense, so I ended up severing the fingerprint sensor for no reason. The back is fairly hard to get off and this ribbon is right where you drag your tool around the edge so it's almost inevitable you'll butcher it - my advice is to leave that but til last, and go around all the other edges, then pull that last bit apart manually and gently. In terms of the fingerprint sensor, what a horrible job. This video is brilliant but also doesn't show how hard it is to get an entry point for getting the middle casing off, which I found to be really difficult and I was waiting for a screen smash tbh. Furthermore, I don't know why, but my middle casing wouldn't come off entirety. Something was causing it to be stuck down to the right hand side of the camera so although all the edges were free, it wouldn't pull off due to being stuck by something in the top middle (yes, all screws were removed). I really tried to remove it but it snapped the plastic at the top between what looks like the speaker holes. So something important was obviously holding it down and I didn't fancy totalling my whole phone so I tried to fit the fingerprint sensor by leaving the middle casing on and pulling it up. This took 3 hours of continuous trial and error, and took years off my life. This thing needs full access and even then, it looked pretty fiddly in the video, so multiply that roughly by 4 million and you've got an idea how near impossible this was was the middle casing still attached. By some miracle, I got the button in, so I taped it in to it's hole to keep it secure and got to work on pushing its miniscule holding clips (one of which has the offending gold ribbon with it, more opportunities to mangle it again!) behind the miniscule plastic housing. A toothpick and tweezers and The Lord are essential. Next job, getting the chip into it's housing. Hahaha, its housing is underneath the part that needs to come off with the middle, which is the part which seems to be stuck down by something immovable. Basically it's like threading a needle and sewing a button in the dark. You manage to lift it by about 5mm and hit and hope for a couple of hours before you all of a sudden feel a small click and freeze in fear of budging it off again with your hands which have now been trembling for half a day of your life. Retreat at the speed of a snail and.reconstruct. Tldr; the camera lense can be replaced easily and without removing the back cover. If you remove the back cover for any reason, you almost certainly will cut the finger print sensor. The middle casing doesn't come off.
You are an amazing writer. The "middle case" passage onward, it is hard to fathom for me. I ordered the 108MP main Quad lens. Before DIY, I will read your post again. if you find out a video that does the job 'carefully', that would help to understand your post better
@@jparkhku @Jay P if you have this exact model of phone (the PRO version) you do not need to remove the back cover or the middle cover to replace the rear camera lense cover. You simply need to get something sharp in one of the corners (smash one if you need to, it'll make it easier) grab the "glass" at that corner point with some tweezers and pull upwards slowly. This will pull the entire lense casing off - it is simply stuck down with glue, no screws. Clean what is left, use a bit of sticky tape to dab around the lense to ensure you remove all the tiny fragments (if applicable) and stick your new lense cover down in the outline of the old one, as you would with a screen protector, it's exactly the same process. Be careful of fingerprints on the glass. As I said, that's how to replace the lens casing on the Redmi Note 10 PRO version only - others models are different
@@jparkhku if you're replacing the actual lense/camera, that's much harder and you definitely need to source videos for this specifically and not just a tear down video of the phone. As I mentioned previously, this video doesn't show something to the right of the rear camera which is secured tightly and won't allow you to remove the middle casing. I presume it's a screw but I couldn't see it and didn't want to start taking things apart that weren't shown on the video.
@@laurat7485 Yes, my problem is a badly scratched main lens itself (108MP). My spare part is about to arrive but I am now doubting if this is really a DIY. Do you think that the first 4:30 of this video will do? ua-cam.com/video/qliO18uGrcA/v-deo.html I think I will manage to dodge the accident of ripping off the fingertip sensor flex connector.
This has helped me , saved my day.. thanks
Goods bhai 👌👌👌🥳🥳
Brother, did you checked the display manufacturer name ?
Samsung pannel
Samsung
@@sachinpawar4294 where it's written ?
@@_mohitraj have you saw it ?
@@dhruvinsojitra409 because he uses a super amoled screen and a super amoled screen made by Samsung nothing else
Video is very good 👍 sir ji
Woow very nice phone even from inside.
Watching from newly bought 10 pro max
Bro ph kasa work kar raha ha avi
Amazing and very nicely opened, Please tell me I didn't find where ia liquid cooling in this phone as I have seen in POCO phones there's liquid coper pipe in the phone, is this phone Trustable for not getting heat up.
Excellent Work...
Thank You..
Good Video, Thanks Brother...
Thanks Indian legend..,
thank you very much for this! I hope you can make more about another phone so we can now how to fix them or can not ... tks
Good video 📸📸
Thank You...
Watching on my Redmi note 10 pro 😍
Me too, I don't feel it's not such a great mobile like how they shown on mobile reviews
@@மண்ணின்மைந்தன்-ள1ம what problems did you face after buying
@@ja3nnamdev404 lots of software issues
@@மண்ணின்மைந்தன்-ள1ம do you think Samsung M51 will be better?
@@k.skeete no idea but redmi note 10 pro is worst mobile.
Thanks for knowledgeable video
Osmmmmm vdo🎉🎉
8:42 Its not OIS , that is auto focus. Gain information before making video
I was like, yeah it shouldn't have one as far as I know, but for me videos turned out quite stable forgetting to turn on EIS.
Does the sound of something loose when you tap the camera with your finger or put the phone vigorously on the table indicates a damaged phone or is it something from the stabilization of the camera and it should be so?
i have the same issue too
Me too...
I think it is an issue, i dont have that thou
Same issue
good job brother 👍
Thank You..
@@ESCBaig 8:43 it doesn't have ois 🥴
Me watching this video from note 10 pro😂
can you tell anything about it 2 years later?
you are the best...
Keeping an eye on recent Xiomi trend of withdrawing special and unique MIUI features like Second Space, I request UA-camrs to please highlight such withdrawal in their reviews of Xiomi mobiles like Mi, Redmi and POCO to help viewers take an informed decision.
They're doing so to seperate midrange phones from flagships
If we see it from business view, second space is very good for us but bad for company.
Just imagine with it we can act as if we have 2 phones.
Not only that miui have dual apps function. So technically you can have 4 same apps on a single phone.
Also removing notification led
Sir can u please this phone speaker teardown how it is in side in main speaker and i have a question for you that if the covering of thin cloth is teared does that effect the sound quality plzz 🙏🙏🙏 answer to this question
thin cloth used for dust resistance, 90% not effect in sound
Thanks bro 🥰🥰
You are really great and interested bro
Good video thanks
after contact with sea water it does not work. Can I use a motherboard antioxidant or isopropyl alcohol cleaning with ultrasound? thanks and congratulations
Thanks ❤️❤️❤️❤️❤️❤️
Nice bro. I'm appreciate it. I have one doubt the redmi note 10 pro max have any liquid cooling?
First and furious
Watching your video from Redmi note 10 pro same color as yours
Video watching from 10promax🙄🙄🙄🙄
Mast laga video dekhne me.
I'm watching from redmi note 10 pro it was very good phone and amazing no heat issues
Display isn't good.. Even it's amoled
@@மண்ணின்மைந்தன்-ள1ம yes display is very nice
Bro game adithe kuda heat avatledha konchem reply eyu bro
@@hotboy931 not nice
@@Pradeepgamer1m semma heat
Technology is just wow!
I love you bhaiya jee pranam
Watching this video from Redmi note 10 pro Max 😎
Watching in pro max😘😘
Note 10 pro watching from Note 10 pro 🙃
I'm also watching redmi 10 notepro max thanks for all
Nice👍👍👍👏
Watching it from my iphone 12 pro max
Very nice video brother 🔥 but there is no ois in that smartphone bro
@Flameraker48 it can be possible, because of the autofocus system, redmi note 8 pro doesn't have ois but it also rattles by shaking...😊
Since you may have opened various brand of smartphones which one you think have done great job in case of hardware like number of switches for many things to connect and reconnect easily or removed easily, hardware durability, simple pattern to adjust many things in small area inside a board etc...
Can I know what is the proximity sensor is it ir sensor or ultrasonic??
Ultrasonic
Actually it's not mentioned anywhere it's based On using gyro sensor
@@Rahul_bhusan Actually it was based on ultrasonic
This phone has a cooling system
Lol duhhh
Yeah LG ac inside this phn😐
@@VishalKumar-cy8dy 🤣
There is no optical stabilization. Also it doesn't have proximity sensor. It uses sound waves to detect if you put it near your ear
and that sucks as screens turn on and off so randomly while on call. and after using power button to switch on and off screen while call also sucks due to this
@@amankumardubey so even if you click on power button during calls, still screen turns on? Or what's the problem with power button that you mentioned?
@@amankumardubey That is the most annoying thing about this phone screen turn off when listening to a whatsapp Audio bad sensor inside this trash device
Very smooth job
do you need to apply adhesive again when you put the cover back? or would the already there adhesive be enough?
For optimal seal you need to clean older adhesive and after that apy new one (can use double stick tape
Wow 🔥❤️ but camera and everything is that na that is redmi says ?
Im watching from redmi note 10 pro bronze as well ..
Painfull,😱
Hai brother,
How is the phone?
Working nice?
Any issue?
@@shijugopinath5647 Its nice phone.
Just my concern is gets warm when on charging. I switch off to charge.
Im thinking to use smaller plug instead of 33W.
I got 25W samsung plug maybe i try like this.
For the rest its all so far so good
I have the global version with 104mp camera. I get a lot of rattling vibration from the camera area if you tap the back or put it down on a hard surface. Do you think this is OIS ?? I thought it only had digital stabilization but looking at you video it looks like optical on the 64mp version.
Does yours make noise from the camera area??
Great video 😃
No ois in note 10 series..
I have note 10 pro and it also has rattling vibration from the camera..
i too have that rattling vibration when tapped or placed on surface ...... it is because the phone has an inbuilt micro gimbal to stabilize video ..so that might have caused the rattling//
@@someoneeternal7575 BS. No it doesn not have any sort of OIS or Gimbal. Its just the housing of the LEns it needs more area to move for focusing. Thats all. When u take a video with Stabilization it will crop the video a lot for EIS. If it had OIS it wouldnt crop it too much. And when taking night shots it will come shaky af. U need a tripod to take night shots.
I have 108 on my 10 pro
@@anonroof2172 noice*
Bhai meri nye phone k redmi note 10pro ki trey fas gyi hai ab Bo niklati hi nhi hai bhoot koshish ki sb ne to ab mai kya kru mi service care k pass jau kya
Kitne paise lge aapko service centre me ??
Good video
Thank You..
সুন্দর ভিডিও
FYI: the easiest way to disconnect the frame is to start under the SIM card tray, there just a thin plastic piece that can be easily bent away of the frame.
Thax 😍😍😍
Sir redmi note 10 me screen guard laga hua hai ya alag se lagana padega
it's there but if u want u can....ok
Internal components ki quality realme 8 ki Better hai ya Mi note 10 pro ki. Waiting for your reply.
Redmi note 10 pro
Imagine. From one phone. How much money he earned.
Not much, UA-cam ad revenue is very less
Reassemble able
Wow 👏 😮 👏
Nice sir ❤️
Bro make teardown video of moto g40 please bro 🤘🏼👍🏼👍🏼
Wow nice
do i need to removeall the camera if im going to remove the whole motherboard?
or i can remove the motherbord withot removing cameras?
You have to Remove the camera
Good👍
You have skill and love for your work keep it up
There is not a OIS, thats focus mechanical, there is mi10t pro which use OIS in budget price
suggestion I would love if you just remove the bgm. and teardown like asmr videos.
Sir apne sab kuch dikhsya phon me vote log to dikhe hi nahi jinhe ham roj dekhte h 😂😂😂😂😂😂😂😂😂😂
really nice. but can also speak up
I have diassambled mine and learnt that there are three diffent screw sizes - please advise which goes where??
Main cam lens for M2101K6G model should be 108MP
Yes
Vedio watching from 10pro 🥳😄
Sir mere mi note 10 pro ka frosted glass break ho gaya hai kya wo change ho Sakta hai and price kya hoga ..
Kis city me h aap
Chennai me sir
Haa bhai mera bhi breake ho gya h frosted glass
Go to mi store and they will replace it with new. But around 2-3k they will charge
Bhai aapko redmi note 10 pro mein Kya Kya problem face ho rahi Hain Kya Kya bugs dekhne ko mile Hain please batao bhai mujhe Bhai Lena hai Kya le Sakta hoon please help
Bro, 1 question, why does your Redmi Note 10 pro have OIS in the main Camera ? I read in spec sheet that the Redmi Note 10 pro don't support OIS on the Main Camera.
No OIS to redmi note pro on 108mp sensor
@•Itz_Justin• note 10 pro with 108..
@•Itz_Justin•
Note 10 pro indian version with 64mp
Note 10 pro max indian version 108mp HM2 samsung sensor
Global there is:note 10 pro with HM2 samsung 108mp sensor.
All phones got same characteristics...
The global note 10 pro and the indian version note 10 pro max is the ones with same samsung 108 camera
If only this guy changed the audio, I wouldn't be so annoyed at this.
Note 10 pro ka display kiyaa note 10 pro max me laga sakte hai ??? Everything to sam hai dono model ka..🤔🤔🤔🙄
Bhai mera redmi Note 10 Pro mex me battery charge ka imoji Dekha raha hai But charge store Nahin ho raha hai kya karne se tik hogaa bhai please bataiye😢😢
Kitna din hua mobile liye hue 😢
Is that a thermal paste at the back of the motherboard?
5:48 weird flex but OK 👌😄
Watching on redmi note 10 pro .... 2023
How to change internal power and volume button strips? How are they attached? Are they soldered? Because I see four silver dots.
Super!!!
Pantastic work so nice
Watchimg using my note 10 pro, i want my phone to be afraid by watching this video together with it so that it will last longer more than 20 years
watching from note 10 pro max🤟
To change the display to an LCD. Does it make a difference to buy with frame or without frame?
Why would you change it to an LCD? An amoled display is better.
@@RanaKhan-dk2ml cheaper to replace, and not that bad compared to a Amoled.
@@matheus-sm7860 AMOLED is better the LCD (except for the burn ins)
I bought this phone recently 😆😆
What's the built-in DAC of redmi note 10 pro since it's hi-res audio certified?
I also want to know this
@@godspeedfilthypeasantblack1968 yeah me too
Which DAC use this mobile
Phone bhaut badiya hai agar ap ke room ka temperature 25-35 tak hai battery draining ki koi problem nahi ayi gamming me bhi bas temperature shai ho aur lag hai camera mast hai
That's not OIS mate, that's PDAF.
This device doesn't have OIS, If it did you could've moved the lens easily 360°