bhai ji agar hm aquafresh ro me sb kuch hata kr kewal aquaguard ki puri kit bina sv aur bina LPS aur bina tds controller ke lagaye to kya result achcha rhega
My kent RO's motor switches on for 1 second then switches off, after 5 seconds it turns back on for 1 second and again turns off, it keeps on repeating in the same manner. If I turn off my ro for 2-3 hours from main switch, my ro starts working normally. My technician said that there is a problem with low pressure switch, but my ro started working normally when the technician came, so I told him that I'll have LPS changed when it'll completely stop working. What do you think about this problem?
I m using Kent grand plus , in it there is no lips, so if I want to instal it what psi powered pls should I use. 2nd , is there DC and ac float switch or DC and ac foot switch are same. Plze guide me Sir, and this video is really very helpful, thank u sir...
hello ! kya booster pump laga sakhte hai jab main input source water pressure kam hai, for increasing the pressure can i use this ro booster pump? my purifier is not a ro purifier.
our commercial RO 1000lph stops due to low pressure.It works on manual mode from 2 months.problem not resolved yet.what may be the problem.Input water supply is OK.please clarify.
Sir ji low prusere sutch commercial RO m lagta hai ki nhi agar lagta hai to kaha commercial ro m batao.please sir ji aap ke bhouth video deka hai bhut samaj nhi aaya .video ho to link batao please sir ji.
As far as I understood thru your video that water will not pass thru low pressure switch. It will only sense the water pressure and switch off pump. Better make a diagram for water flow and power connection also.
Sirjee Overhead tank Khali ho Gaya yani inlet supply stop ho Gaya. Lekin booster pump chalu Tha, isko to automatically stop hona tha. Kya karan ho sakta Hai? Please reply (Lps installed hai-kent ace model)
Dear Sir My water purifier is wasting a lot of water than in the normal case and it is also purifying very less of water to the storage tank. Please guide me how can I repair it ?
Dear, You seem to be confused while speaking , can you please clarify the exact positioning of LPS and SV some time you say it should be at 1st inlet water then you say it should be after Carbon and Sediment filter, kindly clarify or if possible redo the video with proper demonstration and words.
the lps must be before the SV so it can sense the water pressure., and it must be after the sediment filter and pre carbon filter. so it can sense the pressure drop due to clogging of the filters... ok .. ?
Reviewmaza Thanks for the information, I really appreciate your work but please prepare well before posting videos so that it improves quality and trust in your videos. Best of luck!
sir 1 confusion hai is video ko dekhne k bad....aapne SMPS ki positive wire to LPS se laga di but agar RO system m FLOAT switch laga ho to kya karoge? aapne FLOAT switch k bare m to socha hi nahi. agar FLOAT switch or LPS dono lagane ho to wiring kaise hogi...please sir is confusion ko dur kre...mehrbani hogi aapki
Reply to doge nahi per fir bhi....SV Ko, pre carbon aur pre sediment filter ke Baad lagae..ki direct? Ek Baar hindi me jitne advance accessories hai w purifier ki Laga ke Bana do.
Jai Hind. Hindi hai hum... proudly speak hindi
Very useful video and informative
thanx.
bhai ji agar hm aquafresh ro me sb kuch hata kr kewal aquaguard ki puri kit bina sv aur bina LPS aur bina tds controller ke lagaye to kya result achcha rhega
My kent RO's motor switches on for 1 second then switches off, after 5 seconds it turns back on for 1 second and again turns off, it keeps on repeating in the same manner. If I turn off my ro for 2-3 hours from main switch, my ro starts working normally. My technician said that there is a problem with low pressure switch, but my ro started working normally when the technician came, so I told him that I'll have LPS changed when it'll completely stop working. What do you think about this problem?
I m using Kent grand plus , in it there is no lips, so if I want to instal it what psi powered pls should I use. 2nd , is there DC and ac float switch or DC and ac foot switch are same. Plze guide me Sir, and this video is really very helpful, thank u sir...
Lps is connected series with pump or sv?
can you make a video on how to install a HPS with a pressure tank??
Am using for water sprayer. Useful video
Great 👍
Thank u very much. Good video.
hello ! kya booster pump laga sakhte hai jab main input source water pressure kam hai, for increasing the pressure can i use this ro booster pump? my purifier is not a ro purifier.
Very informative, thank you sir !☺
Lps Ac supply main use kre ya DC supply main???
Good work bro i need more details about low pressure switch how to buy what is the actual name about this switch reply please
Good video... thank you.. I now know how to connect my RO unit
Hi How to connect with You I have some queries regarding under sink ro
Hi...could you pls draw schematic of the system in the video? Thanks
Can we use lps to turn on/off on booster pump based on valve open and close ? Does it work without solenoid valve ?
I just want an indication, using LPS Whether water supply from municipal is still coming or not.
Bhai Maine LPS ka connection SV ke saath apke bataye tarike se Kiya but meri SV heat karne lagti hai 2 SV Badal Chula him kya karun
Is it useful for uv
Sir ac before smps me connection kare to jyada acha rahega
many many thanks ❤️
Can i use LP switch to cut off air compressor if pressure is above a certain psi
Air pressure switch are different.this is for water
@@reviewmaza oh i am looking for a alr pressure switch to cut 9f at 18psi and start at 10psi
what kind of lps use for ro aqua grand model, name the products name good one
kya Ro filter hony k baad Weaste water washing machine m use kar sakta ho ?
+abid hussain tds jyada hoga to nhi
I need PCB/MOTHERBOARD of Aquaguard Enhance RO+UV. Please help.
What. Is the need of solenoid valva?
You have not connected it to the float switch? Does this makes any difference?
flow switch is very important because it will cut off current when tank fulled but in this man's case he miss that.
Solenoid valve ko parellel mein lagaya hai with DC output
2) LPS ko series mein lagaya with DC current output
our commercial RO 1000lph stops due to low pressure.It works on manual mode from 2 months.problem not resolved yet.what may be the problem.Input water supply is OK.please clarify.
Low pressure switch kharab ho gya hoga ya uska setting karna padega
There is any electric connection of los & uv.
Sir ji low prusere sutch commercial RO m lagta hai ki nhi agar lagta hai to kaha commercial ro m batao.please sir ji aap ke bhouth video deka hai bhut samaj nhi aaya .video ho to link batao please sir ji.
Commercial ro me ye nhi lgta alag wala lgta h
As far as I understood thru your video that water will not pass thru low pressure switch. It will only sense the water pressure and switch off pump. Better make a diagram for water flow and power connection also.
Can we remove the connection of low pressure switch in kent RO? If no than tell me the contraindications from this.
+Tarun Jadoun yes you can remove , but you will have to take care if the input water is not available
Reviewmaza Thank you very much
Sirjee
Overhead tank Khali ho Gaya yani inlet supply stop ho Gaya. Lekin booster pump chalu Tha, isko to automatically stop hona tha.
Kya karan ho sakta Hai?
Please reply
(Lps installed hai-kent ace model)
Float switch change karo na yar
Sir low pressure switch kis liye use karna hai aur use karne say kya fayida hai plz explain
+Syed Iqbal plz see my video on lps
bhai hindi mai bol lo agar english mai comfartable nhi to..kuch smjh nhi aara
If I will remove connection of uv from ballast what happen.
Thnks dear its very usefull for me
What about float wall connection bro. Please explain connection
Nice information
Super brother👌👌👌👌👌
Dear Sir
My water purifier is wasting a lot of water than in the normal case and it is also purifying very less of water to the storage tank.
Please guide me how can I repair it ?
+Rahul Soni replace the inline filters and ro membrane
Sir, will that be necessary to change the sediment and post carbon filter while changing RO membrane ?
Dear, You seem to be confused while speaking , can you please clarify the exact positioning of LPS and SV some time you say it should be at 1st inlet water then you say it should be after Carbon and Sediment filter, kindly clarify or if possible redo the video with proper demonstration and words.
the lps must be before the SV so it can sense the water pressure.,
and it must be after the sediment filter and pre carbon filter. so it can sense the pressure drop due to clogging of the filters...
ok .. ?
Reviewmaza Thanks for the information, I really appreciate your work but please prepare well before posting videos so that it improves quality and trust in your videos.
Best of luck!
Mujhe bhi lps ka diagram paper mein chahiye. Jadhav ji will u help me.....
If motor run dry what happen
Water seal damage and waste power
I have thimbal wire can i do the same connection coming to sv
Yes
@@reviewmaza thanks
thank u for the video!!
+dev Km thankx 4 watching
@@reviewmaza can I get your email id
sir 1 confusion hai is video ko dekhne k bad....aapne SMPS ki positive wire to LPS se laga di but agar RO system m FLOAT switch laga ho to kya karoge?
aapne FLOAT switch k bare m to socha hi nahi. agar FLOAT switch or LPS dono lagane ho to wiring kaise hogi...please sir is confusion ko dur kre...mehrbani hogi aapki
+vicky singh pehle wire lps me jayegi , fir uske baad float switch me jayegi. Fir aage pump aur sv me jayegi
Reviewmaza thank you sir....ab smaj gya
Jadhav is tarah to smps me 220 volt ki direct supply chaalu rahegi .
Kya hai yar tera english,hindi me baat kar to... problem hai kya ...kuch be smj me nahii aaya
school ja pehle...fir vapas aa
Jadhav ji yadi aap lps ka diagram paper pr bna sake to easily samajh me aa jaega isme thoda confusion create ho raha hai
+Sharad Chitransh Johri ok
Jhadhav ji very very thnx.
Mujhe bhi lps ka diagram paper mein chahiye. Jadhav ji will u help me.....
Good video sir
Sir, what is the use of Low Pressure switch?
low pressure switch is used to protect motor from dry running .and also protect the membrane.
Thank you so much sir.. Your videos are awesome.. Very enlightening..
+Abir Karmakar thankyou
Bhai English gruri nahi gruri hai satisfaction Hindi mai bat kro please
Where to install TDS adjuster
+zeeshan zafer i have a video on it . Pl see
Reply to doge nahi per fir bhi....SV Ko, pre carbon aur pre sediment filter ke Baad lagae..ki direct? Ek Baar hindi me jitne advance accessories hai w purifier ki Laga ke Bana do.
+S.A Everything kyu nahi denge bhai,
Sv Ko sediment aur carbon k Baad lagana hota h.
Reviewmaza thanks bro...you are too sweet....
low pressure switch kya kaam karta hai
Please upload circuit diagram pictures end of the video
mere sabse acche bhai please talk in hindi... your eglish is so bad
भाईजी जिनदी बोलने में शर्म क्यों करते हो। जिस भाषा में अच्छे से बता पाओ वो इस्तेमाल करनी चाहिए ।
Los is to.connect series
भाई साहब वीडियो शुद्ध हिंदी में या पूरी तरह इंग्लिश में बनाया करें कुछ भी समझ में नहीं आता है आप हिंदी और इंग्लिश की खिचड़ी बना देती है
भाई हिंदी नाही आती क्या?
Bhsi hindi bolate to bhi chalata
Hindi me bataya kejiye
ac& dc mantion there is no clear
Dc only
बोलना सीख लो, आपको खुद doubt है
Hindi m bolle ya America chala ja
Hindi mein jyada acche se tum bata sakte the English nahin aati Tumko
पहले हिन्दी में बोलिये, वर्ना England जाओ
Hindi me hi bol le
Hindi ata ha ka
You need to rehearse what you want to convey. Your content is ok but So much repetition and so uncomfortable with language your good video is ruined
English nahi bolini ati mat bol.
hindi mai bolne mai sharm aati h kya
Your lecture delivery capability is very very poor. Please do not try r
to do this and leave it.
Very bad