How to repair a Volitation 9053, 9101, and other coaxial RC helicopters

Поділитися
Вставка
  • Опубліковано 27 січ 2025
  • PLEASE TURN ON ANNOTATIONS FOR MORE INFORMATION AND LINKS TO RELATED VIDEOS. The most common problems for low power are a weak battery, loose linkage, or worn motor. This video describes how to fix the most common problems of coaxial helicopters.

КОМЕНТАРІ • 229

  • @hammydude12345
    @hammydude12345  13 років тому

    @mrrobvs No, if you use a 7.4v lipo it won't produce too much power. The lights are LEDs.

  • @stephenreynard8551
    @stephenreynard8551 10 років тому

    My 9053 was doing this aswell there are 2 little black screws just above the 2 big cogs all i did was tightened the screws worked for me good luck

  • @hammydude12345
    @hammydude12345  13 років тому

    @mrrobvs You should use 7.4 volt lipo batteries. These helis use JST type connectors, you can find batteries with these connectors already attached, but I have switched to Deans connectors. To fit the housing measure the stock battery and look for an upgrade that is the same size or use velcro to fit the battery below the canopy. Any 7.4v lipo charger will work.

  • @hammydude12345
    @hammydude12345  13 років тому

    @burgna If you want to use a more standard connector like a Deans connector you will have to solder the wires on.

  • @mohsinsaida
    @mohsinsaida 2 роки тому

    How to open main bled grip

  • @audis6m
    @audis6m 12 років тому

    I searched the internet and I know that I lost also bush from main shaft ,so now I know what I need to repair 9053 thanks

  • @0269Reaper
    @0269Reaper 12 років тому

    Should the bottom blade have any play in it? I can hold the gear and turn the blade mabe an inch before it catches. The screws that hold the plade to the shaft came out of the holes after a crash, and could not be tightened enough to make contact with the holes again, so I used a slightly longer screw. It flys fine, but I wonder about the play in the lower blade. The top blade has no play in it.

  • @metalheadmike1000
    @metalheadmike1000 12 років тому

    when i crashed mine it hit the ground nose first, broke both screw studs that hold the board down and the antenna wire came off the board. i had to desolder the wire that was still in the board and run the wire again. its very close to the upper frame too if that matters?. but after a few replacement parts its flying again. what bugs be is a lag time between the transmitter and the helicpoter, about a 1/2 a second. when i throttle down the it still keeps spinning which is bad when it hits dirt.

  • @AceMcSpade
    @AceMcSpade 13 років тому

    when i push up on the left control stick the blades spin for about a quarter of a second and then cuts out. I've had it for a week and and had about 7 sessions with it. Your video makes me think it could be a battery issue.

  • @hammydude12345
    @hammydude12345  13 років тому

    @GamerKing112 I recommend using Dean connectors. I use lipo batteries, 7.4v from 1800 mAh to 2200mAh.

  • @babyeater1228
    @babyeater1228 13 років тому

    i recently got this helicopeter and it was awesome while it lasted. one day i was flying it in the garage and all of a sudden the motors quit working and the helicopter landed. then i tryed to take of and it burst into flames. i changed all the wires and fixed the chio up a llittle and everthing seems to be workin fine but exept for the mototrs. even the lights and the power but not the motor what do u think i should do? i already replaced all the burnt wires but wnt work. what should i do?

  • @teratonexplosion
    @teratonexplosion 13 років тому

    Thank you very much for your video. My helicopter only flies backwards, even if the forward/backward joystick is all the way up. The most i can get it to do is stand still. I hope the modeling clay will solve my issue. I have one question though: Why is my helicopter always swaying to the side? Mainly to the left. I don't mean like spinning to the left but moving parallel to the X axis? I would appreciate it very much if you could help me. Thank you in advance.

  • @hammydude12345
    @hammydude12345  13 років тому

    @freediverga If LEDs don't come on it is either a connection, the on-off switch or your receiver.

  • @55andovagaming
    @55andovagaming 13 років тому

    This video was very helpful it gave me the idea to use crazy glue on the lower blade grip to the hollow shaft because I stripped the screws he was talking about @1:25 into the video.Oh yeah the crazy glue worked like a charm.

  • @esteban19h08m
    @esteban19h08m Рік тому

    i actually have 2, and i am going to desolder the microncontroller to see the hexadecimal rx and tx from the brand, thank you for the tips

  • @0269Reaper
    @0269Reaper 12 років тому

    The problem is the screws that hold the blades to the shaft are very small and barely make contact with the holes in the shaft. I used a slightly longer screw and that fixed the problem. You can't use a paperclip, because the upper blades' shaft has to go thru the outer shaft. The other problem you might have is the gear on the lower blades might need the screws tightened. I had to use longer screws on it too. Just not too long. You don't want the screws to touch the inner shaft.

  • @hammydude12345
    @hammydude12345  13 років тому

    @simmons527 I have no idea. My 9053 is rock stable. I would try more weight on the right side.

  • @CYOTsNiper
    @CYOTsNiper 13 років тому

    @hammydude12345 I traced all the wires coming from the battery and switch and found a really loose wire from the switch that was from poor soldering job. I'm going to pick up a solding iron tomorrow. I'm going to do some practice runs on some scrap wire. I have some new mods for you Super Cub coming up so I'm going to need to the practice.

  • @mikelutz32
    @mikelutz32 13 років тому

    with the new battery was there any modifications you have to do to the connectors that connect the battery to the heli or the charger? Or are the connectors pretty much universal?

  • @hammydude12345
    @hammydude12345  13 років тому

    @biggs374 It could be many things. Are you sure your battery is charged? Else it could be bad receiver, poor connection etc.

  • @metalheadmike1000
    @metalheadmike1000 12 років тому

    there was always a delay when tring to shut down the main blades. i tried setting the trim man times and have the transmitter as low as it will go to turn the blades on, but just keeps spinning after i throttle down. its not good cause it will end up stripping the gears or break somehing on the heli by not shutting down when falling or tring to miss an object in flight. i replaced the board so it shouldnt be that.

  • @gillieskyler
    @gillieskyler 12 років тому

    hey the paperclip through it to hold it together is stupid idea the other bar has to pass through it and spin freely

  • @hammydude12345
    @hammydude12345  13 років тому

    @brickman9876 Take off the canopy and see if the motor towards the back is running. If not, then the motor is probably burned out or you have a loose connection.

  • @hammydude12345
    @hammydude12345  13 років тому

    @teratonexplosion Try putting some weight on the right skid this may help.

  • @NikhilThanikella
    @NikhilThanikella 11 років тому

    there is a plastic thing between the upper wings and the black stick. In that one is not there and i think it is not flying because of this. can you show me a video about this problem. I want your answer fastly. pls pls show

  • @ajwgtnz
    @ajwgtnz 13 років тому

    Hi Mate,
    One more thing could you explain the battery connectors. Is it the JST-XH connectors I require on a new battery want to keep it the same and not fart around changing over to the deans connector ,but in saying that would the Lipo battery burn out the the JST plug?

  • @sonicalstudios
    @sonicalstudios 13 років тому

    Thanks Mate, I Have Revell's Version Called The Big One. Its exactly the same Unit But Made from Revell. I had some battery Questions but you just fixed that....lol! Thanks for that.

  • @Allaraine88
    @Allaraine88 12 років тому

    I have also crashed once with mine and the bottom set of blades barely turn now. I have tried to tighten the screws but they will not tighten anymore. How can I fix this? I thought I heard him say "Put paperclip in the hole and bend the ends around to fix this"? Is this correct? Won't this take it out of balance?

  • @N2RIT
    @N2RIT 12 років тому

    I purchase one of these Double Horse last week from a Hamfest. Got it home charge up the battery. Then tried to fly it. The helicopter would not lift up off the ground. Blades spin very fast, I can get it to turn left and right but will not lift off the ground. What could be wrong.

  • @ToolforPychos
    @ToolforPychos 11 років тому

    my bottom blades aren't wanting to spin on my FQ777. I think I have a loose wire.

  • @dougschif
    @dougschif 13 років тому

    i have a similar helicopter the black widow. looks just like yours. mine keeps cutting out of power after like 5 seconds, it gets up in the air a little and comes right down. it powers right back up and cuts right back out. any ideas. i have fresh batteries and have charged it.

  • @hazza2910
    @hazza2910 12 років тому

    my main rotor head snapped so i ordered a new one and now i cant get the old one of the shaft

  • @nickdu88
    @nickdu88 12 років тому

    Thanks for the video. I got a used identical model volitation. I replaced it with a new balance bar and main board and i am having some trouble. I am wondering what might be causing the heli to spin out of control at first flight? (something with gyro not working im guessing? Also, sometimes, the heli runs out of sync with the joystick on the transmission. It shuts off in mid flight or slow startup/shutoff of the blade rotation. Any hints or ideas? greatly appreciate, thanks!

  • @olakeonda9471
    @olakeonda9471 12 років тому

    i have a 9051 volitation heli but it wont fly because it drifts it self to the right if you can tell me how to fix it i would appriciate that thank you

  • @markjohnson6224
    @markjohnson6224 11 років тому

    Any suggestion on how to repair what I believe to be stripped screws on the top gear that drives the bottom blade? Thanks!

  • @Demon11775
    @Demon11775 13 років тому

    Where can i get a battery and a charger that you mentioned? like the ones you got

  • @hammydude12345
    @hammydude12345  13 років тому

    @freediverga Good luck, if you can't solder the wire back on you can simply disconnect the other wire and twist the ends together with some tape for insulation. Plugging in the battery will work ok as an on-off switch.

  • @AceMcSpade
    @AceMcSpade 13 років тому

    Do you have any videos on how to replace the battery? I got a new battery but the plugs are a different size.

  • @hammydude12345
    @hammydude12345  12 років тому

    If the main board is new it is probably ok. Since the heli is used, my guess is that one of the 2 main motors is wearing out. the video will give some suggestions to find out which one is the problem, or you could replace both motors. good luck.

  • @hammydude12345
    @hammydude12345  12 років тому

    do both main rotors do this or only one? did you used to work? my guess is that your motor is wearing out and needs to be replaced.

  • @Zippo765
    @Zippo765 12 років тому

    One thing I would recommend when unraveling the antenna wire, is to use cable ties to secure it to the tail tube. Less chance of it coming undone from the rear stabilizer fin, and getting tangled in something.

  • @Tracino234
    @Tracino234 12 років тому

    I have a doublehorse 9101, and whenever i start it, i slowly throttle it from slow to fast, and as i increase the speed, the rotor spins faster, but then bogs down and stays at the same speed, and then stops completely at full speed. Then the red LED blinks. Please tell me how to fix as soon as possible? Thanks.

  • @hammydude12345
    @hammydude12345  13 років тому

    @ajwgtnz Try a half ounce (14 grams) in the nose of the canapy to start. I don't have a 9101 but I think the blades are farther apart than in the 9053, unless your blades hit each other your won't need to reverse the lower blade grip.

  • @simmons527
    @simmons527 13 років тому

    HELP.....I just purchased the 5093 and it drifts to the left, what is the problem? I tried weights on other side (2 AAA BATTERIES) which helped. But it still wants to fall over to the left side.

  • @CYOTsNiper
    @CYOTsNiper 13 років тому

    @dougschif My hello just started doing that and now won't power up at all with either of the two batteries i I have. led's don't even come on so I think my reiver is shot.

  • @teratonexplosion
    @teratonexplosion 13 років тому

    @hammydude12345 Thanks for your reply. Yes, 3ch coaxial DH 9101. Yes it always moves to the left.. The balance bar is all straight, no bends. I guess the problem is the cheap quality.

  • @hammydude12345
    @hammydude12345  13 років тому

    @khonglap Can't tell, it could be the transmitter or receiver.

  • @butzjr
    @butzjr 11 років тому

    I need to replace the plastic gears that sit between one of the main motors and the large gears that turn the drive shaft. Do you have any videos that show how to take those out and replace them? Thanks in advance!

  • @mrrobvs
    @mrrobvs 13 років тому

    @hammydude12345 Nevermind, I see that it also says "LI-ON" on the item itself. Is there some sort of setting on these things to make sure you're not pumping too much juice? Also, how do the lights work on these things? The "directions" printed on the item, indicating how the lights work- appear to be written in Chinglish.

  • @carlosslghouston
    @carlosslghouston 12 років тому

    Where can I get a new battery and the battery charger you have?

  • @tivop17
    @tivop17 13 років тому

    what kind of lipo battery use these heli and whats the life of battery

  • @Zippo765
    @Zippo765 12 років тому

    Also, what is the smaller coax on the left at 3:43 ? I have one that is similar in size and build, and I am looking for replacement motors that will fit. The Heli I have is a knockoff of some sort (from Haktoys) and The B motor is shot.

  • @MiDLiFECRYSiS
    @MiDLiFECRYSiS 13 років тому

    so what type of connector does the volitation need for batteries? i can't seem to find the battery you show.. what is it called?

  • @hammydude12345
    @hammydude12345  13 років тому

    @kdabiznessman Thanks for the comment, that is a great suggestion.

  • @gregsylvester66
    @gregsylvester66 12 років тому

    Hi, I've recently bought a double horse 9115 & I've got a problem turning right. Simply put both motors are spinning fine and I can see and hear the change in the motors when I turn left, but when I turn right there is no change both motors spin at the same speed.
    The heli is brand new out of the box and I've only had it a week! Can you help?
    Cheers G

  • @hammydude12345
    @hammydude12345  13 років тому

    I don't know what kind of helicopter you have, but many have screws you can loosen, move the motor over, then re-tighten.

  • @danbutton781
    @danbutton781 6 років тому

    Just had one transistor desolder it self n fall out it’s the small ones you talk about Could you please tell me the larger transistor code?

  • @laphong341
    @laphong341 13 років тому

    Please help if the remote control won't work ?. What is wrong with remote control ?.
    Thanks

  • @johnllewellyn6720
    @johnllewellyn6720 12 років тому

    hi can some one help i av a 9053 double horse
    i need to change the gears an motor is there a video to show you how
    thanks

  • @mrrobvs
    @mrrobvs 13 років тому

    I am using a 9104 and thinking about the purchase of a 9101. I've been unable to find more specifics as to what I'm looking for in a battery upgrade in these types of helis. Is it possible to find one with the correct connectors already attached? Where? A direct link would be great.A certain size that will fit in the stock housing? What cap. volts or amps? How do I find a charger which pairs properly? Is it user-friendly to charge these lipo batteries (an indicator) or Will stock charger work?

  • @TuningFork426
    @TuningFork426 13 років тому

    Do the tail rotor mod and switch the balance bar to a 9077 that should get u going forward

  • @hammydude12345
    @hammydude12345  13 років тому

    @dougschif Did it ever fly okay? My guess is that the receiver is bad.

  • @mrrobvs
    @mrrobvs 13 років тому

    @hammydude12345 Okay...last question I promise. The model you pointed me to says the output is 800mah. The battery is 1300mah. Will this produce only a partial charge? Is it inadequate?

  • @callofdutyfreak39
    @callofdutyfreak39 13 років тому

    and will it cause im getting a li-po battery and i have a li-ion charger plz plz i need to know thankyou so much

  • @hammydude12345
    @hammydude12345  13 років тому

    @mikelutz32 No, there are lots of different connectors. I like to use Deans type connectors.

  • @RCFreak1231
    @RCFreak1231 13 років тому

    can we replace the battery with an alkaline 9 volt
    bateries and is that idea is save
    please reply

  • @LostJ
    @LostJ 11 років тому

    Mine doesn't even start up but the l.e.ds come on, although I don't have an antenna? Could this be the problem

  • @N2RIT
    @N2RIT 12 років тому

    I purchase a 3300 mah battery and found out its to big for the 9053 Heli, will a 2200 mah battery work in the 9053 heli Would like to get more flying time out this heli

  • @hammydude12345
    @hammydude12345  12 років тому

    Did it respond quickly before the crash? Perhaps the receiver board was damaged to cause the 1/2 second delay?

  • @hammydude12345
    @hammydude12345  12 років тому

    The top rotor head on 9053 and 9101 is glued on the inner shaft and you will need to replace it and a new inner shaft.

  • @hammydude12345
    @hammydude12345  13 років тому

    @sinaland You're welcome, glad it helped!

  • @hammydude12345
    @hammydude12345  13 років тому

    @mrrobvs They are wrong, lipo batteries are best. The higher the mAh the longer the flight, but the battery will weigh more.

  • @mrrobvs
    @mrrobvs 13 років тому

    @hammydude12345 Great. Thanks. Would you recommend any particular mah? A hobby shop that sells these things recommending not using lipos because the "board can't handle it." I guess you would disagree?

  • @hammydude12345
    @hammydude12345  13 років тому

    @teratonexplosion I assume your heli is a 3 channel so there is no control of lateral movement. Is it a coaxial? If the shaft to the blades is bent that can cause it to sway. Did it always move to the left? Good luck...

  • @JollyRogga
    @JollyRogga 13 років тому

    Purchased a 9101, I used the trim slides to obtain a neutral trim but the helicopter still seems to, in flight, bear backwards and rotate slightly. Do you have any suggestions or videos you know about that I need to look at to fix this? I thought that a slight relocation of the tail fin might assist this. Yes/No? Thanks in advance :)

  • @brickman9876
    @brickman9876 13 років тому

    wat do you do if the bottom blades dont move but the top do.PLEASE HELP!!!!

  • @johnllewellyn6720
    @johnllewellyn6720 12 років тому

    hi does any 1 no y my bottom blade is freely spinnig on my 9053 i av changed the gears there is no power 2 the bottom blade it does spin but wen moter stops the blade still spinns freely

  • @hammydude12345
    @hammydude12345  13 років тому

    @ThePerkipro Look for a loose connection. Cant say for sure but probably is a bad receiver, I think you can get them on ebay for about $10 - $15.

  • @angelamyers3900
    @angelamyers3900 6 років тому

    We have a 9101 double horse that the spindle fell out. We can not figure out where to put it back. Can you help??

  • @hammydude12345
    @hammydude12345  11 років тому

    it could be one of many problems, have you checked the connections on the heli control board?

  • @hammydude12345
    @hammydude12345  13 років тому

    @ajwgtnz They are standard JST plugs, they can handle the power from a lipo battery and won't burn out.

  • @MotorcycleRiderUK
    @MotorcycleRiderUK 11 років тому

    Any reason why both blades would spin the same way on a coaxial?

  • @hammydude12345
    @hammydude12345  12 років тому

    sorry, i haven't tried shortening the flybar so i don't know, also don't know about the 9077

  • @PrimerCord
    @PrimerCord 12 років тому

    hi there verry informative looking for that battery and charger

  • @aboengeducation6410
    @aboengeducation6410 5 років тому

    Menurut pengalaman yg sy alami, ketika gear sdh di cek gak ada masalah dan battery yg keadaan full. Tp gak bs terbang jg, itu bs disebabkan signal dr remot atau transmiter lemah

  • @bobbymalta73
    @bobbymalta73 12 років тому

    Hello mates whar`s the best the volitation or the 9118 the one with the writings of HELICOPTER?

  • @hammydude12345
    @hammydude12345  12 років тому

    Yes I bent the balance bar up and attached it to a carbon rod (it is in the decorative bars). Please see my videos on DH 9053 for more info.

  • @hammydude12345
    @hammydude12345  13 років тому

    @mrrobvs Lipo and Li-ion chargers are the same.

  • @Jdowns32_
    @Jdowns32_ 13 років тому

    Where do u get lithium battery?

  • @my74vette
    @my74vette 7 років тому

    Excellent demonstration. My problem is my double horse 9053 will not back up. The rear blade seems to be working correctly. any ideas?

  • @96kicking
    @96kicking 13 років тому

    what if th back blade wonte spin pleas help

  • @ajwgtnz
    @ajwgtnz 13 років тому

    @hammydude12345 >>>I have a DH 9101 wanting to know how to improve fwd momentum how much weight do I need to add to the front end of the craft? Also have tried the reverse lower blade shaft, but it looks like it will strike the canopy is there anyway to overcome this? I've tried adding weights on top of the battery but it ended up snapping the lower fan clip.

  • @metalheadmike1000
    @metalheadmike1000 12 років тому

    I have this same model also, does anyone know what other models are interchangable as in motors, batterys, rear blade and any other parts to make this work much better? I dont plan on dumping a bunch of cash into this hobby so just some good low cost but good quality parts that will direct bolt on to this 9053. i havent flown this very much but it does not like to move forward or backwards very well. the battery has about 6-8 uses on it and it doesnt last as long as it did. its a great heli tho!

  • @hammydude12345
    @hammydude12345  13 років тому

    @AceMcSpade Sorry, I don't have a video on how to solder. But it's not hard treat the surfaces with acid flux and I bet you'll be successful.

  • @audis6m
    @audis6m 12 років тому

    hi i crash my 9053 , upper blades mount is broken and pin who hold mount is missing , i have new mount but i cant find and buy nowhere new pin , please make movie wher you show how look pin and how put everything back together

  • @odlanyersurabia3774
    @odlanyersurabia3774 8 років тому

    how fix tail blade not work thats why no forward and reverse help me please

  • @brualkiller831
    @brualkiller831 12 років тому

    wat if the bak tail wing wont spin?

  • @hammydude12345
    @hammydude12345  12 років тому

    You will need to solder it back onto the receiver board.

  • @hammydude12345
    @hammydude12345  12 років тому

    That is surprising, I've flown my 9053 hundreds of times and plastic gears are okay. Did something jam the blades? This could cause the gears to be chewed up.

  • @hammydude12345
    @hammydude12345  13 років тому

    @Kryptosuras Hard to say. My guess is that your battery or the battery charger is bad.