thanks for the feedback. I have several other homemade powder coating gun made after this one and I only used materials readily available. It should be a lot nicer with a 3rd printer.
Hi Michael. Thanks for subscribing. That I think is the first homemade PC gun I made during idle times at work. I have since made several improvements. The latest one in this video if you want to see: ua-cam.com/video/aevtL9Id4ms/v-deo.html
let’s not forget a very big part of this scheme. The powder particles must leave the tip of the gun positively charged in order to be attracted to the negatively charged part and adhere. to even stick properly, you’re talking 10,000V plus (especially when navigating the faraday affect I’ve enclosed shapes. I like the inside of a bowl) And that’s where it gets tricky. It’s also where it gets dangerous. Dangerous, as in, one false move… and it’ll blow your feet off your body.
Hi. When navigating faraday cage areas, you want to reduce the kV of the gun. The powder coating guns in general make very high voltages up to 100 kV. But these are low power outputs. The current on these guns are only in 10s of microamps. It will give you a shock but definitely not lethal.
It’s not that dangerous. While voltage is high, current is very low. I made a very similar electrostatic gun a couple years ago and shared it with another UA-cam’er and while it worked great, it was difficult to find wire with thick enough insulation to stop massive static buildup.
If you heat the part to be done first, you don't need the electrostatic charge. Just make sure the part is up to curing temp before you spray it and the powder will cure to it on contact.
Hi. This is an older video and some of my very first attempt to make a homemade powder coating gun. There has been several updates and improvements so please check it out in my channel. Thanks
hi sir sa nakikita ko di pa nag ggrow channel mo sana tumaas na maganda content mo boss marahan lang galawan at detalye swak sa mga katulad ko n nghhanao ng gantong tutorial. excited nku sa dt mo sir
hi sir salamat sa comment. ok lang yun kasi hobby lang naman ito. sinisingit ko kung wala gaano trabaho dito sa pinapasukan ko. ang focus ng channel natin ay informative hindi entertaining, kaya siguro konti lang ang audience.
@@DIYPhil tama sir informative talaga iyong channel. Maraming beses na ako pabalik balik sa engine disassembly/assembly ng DT. Maganda din quality over quantity. Napakadali makita yung kailangan kong video. Madiskarte din approach mo sa tools. Imbes na bumili (at minsan lang ginagamit), gumawa na lang.
Hi. Be sure to watch the other videos in my channel on the Homemade Powder Coating playlist. This is the earliest version and has a lot more improvements since then. Thanks.
thanks bro. may mga kasunod pa yan na video, pati yung DIY ko na oven pang bake nung na powder coat. busy lang sa work kaya hindi ko pa na e-edit video clips.
Yes there is. The construction of the power supply is on another videos. do check these out: ua-cam.com/video/8Nywhih1QJQ/v-deo.html ua-cam.com/video/jJm6EpnzTnQ/v-deo.html
eh nasa 10 psi lang ang kailangan sa pag spray ng powder. kahit yung maliliit na compressor kayang kaya. yung isang version nga sinubukan ko blower lang eh. tingnan mo to: ua-cam.com/video/V3WGkSkLMIg/v-deo.html
yung cylinder block, cylinder head, chassis, tank, swing arm. bale halos lahat po ng part na yari sa metal. yung right crank case cover din sana kasi iyun yung unang unang nagagasgasan ng pintura, kaso napinturahan ko na ng spray paint.
@@DIYPhil yung powder coat daw sa hi temperature at regular ay magka-iba. Nag inquire ako dito sa amin pero specialty nila ay mga rims. Yung sa makina lalo na sa mga mainit na mga part special powder coat ginagamit.
@@idselseno2306 thanks sa info. nakabili na ko ng powder, black. nung bibili ako 2 yung pamimilian. yung mas mahal ang binili ko na made in USA daw. tapos mas mataas yung curing temperature kaya baka yun na yung special powder. pero check ko pa rin sa supplier.
nice idea.. created a whole one piece using 3d printer. and it work FLAWLESS.. been using a 1 year now...
thanks for the feedback. I have several other homemade powder coating gun made after this one and I only used materials readily available. It should be a lot nicer with a 3rd printer.
Can you provide the files for it? :)
Just wow! Very very creative yet super simplistic approach..👍✅
Hi. it is a work in progress trying to solve the short comings of the homemade gun. Hope you look into videos updates of this gun as well
Nicely done!! Can't wait to see it all out together.
Hi TS. I'm glad you found this. It's working fine but still need some improvement. I'll upload the other videos soon.
hello from usa, very nice work! you have a good brain. i bought my powdercoat gun used and cheap, but you really nailed it. make your own.
Hi Michael. Thanks for subscribing. That I think is the first homemade PC gun I made during idle times at work. I have since made several improvements. The latest one in this video if you want to see:
ua-cam.com/video/aevtL9Id4ms/v-deo.html
let’s not forget a very big part of this scheme. The powder particles must leave the tip of the gun positively charged in order to be attracted to the negatively charged part and adhere. to even stick properly, you’re talking 10,000V plus (especially when navigating the faraday affect I’ve enclosed shapes. I like the inside of a bowl) And that’s where it gets tricky.
It’s also where it gets dangerous. Dangerous, as in, one false move… and it’ll blow your feet off your body.
Hi. When navigating faraday cage areas, you want to reduce the kV of the gun. The powder coating guns in general make very high voltages up to 100 kV. But these are low power outputs. The current on these guns are only in 10s of microamps. It will give you a shock but definitely not lethal.
It’s not that dangerous. While voltage is high, current is very low. I made a very similar electrostatic gun a couple years ago and shared it with another UA-cam’er and while it worked great, it was difficult to find wire with thick enough insulation to stop massive static buildup.
If you heat the part to be done first, you don't need the electrostatic charge. Just make sure the part is up to curing temp before you spray it and the powder will cure to it on contact.
Nice! Very creative.
Hi. This has been updated several times. Go check out the latest in the link below:
ua-cam.com/video/aaLc6K-r8Ic/v-deo.html
nice work, looks like quality
Hi. This is an older video and some of my very first attempt to make a homemade powder coating gun. There has been several updates and improvements so please check it out in my channel. Thanks
Mabuhay ka kabayan❤
Maraming salamat po
Nice video.. For DIY.. 👍🏻👍🏻👍🏻
thank you very much. and hope you also see the updates to my homemade powder coating gun and power supplies.
hi sir sa nakikita ko di pa nag ggrow channel mo sana tumaas na maganda content mo boss marahan lang galawan at detalye swak sa mga katulad ko n nghhanao ng gantong tutorial. excited nku sa dt mo sir
hi sir salamat sa comment. ok lang yun kasi hobby lang naman ito. sinisingit ko kung wala gaano trabaho dito sa pinapasukan ko. ang focus ng channel natin ay informative hindi entertaining, kaya siguro konti lang ang audience.
@@DIYPhil tama sir informative talaga iyong channel. Maraming beses na ako pabalik balik sa engine disassembly/assembly ng DT. Maganda din quality over quantity. Napakadali makita yung kailangan kong video. Madiskarte din approach mo sa tools. Imbes na bumili (at minsan lang ginagamit), gumawa na lang.
sir anung purpose ng electrostatic chamber.
So nice and very very good video Muhammad Latif Master Lahore Pakistan
Hi. Be sure to watch the other videos in my channel on the Homemade Powder Coating playlist. This is the earliest version and has a lot more improvements since then. Thanks.
so good i subscribed. well done, sir.
Awesome, thank you!
Nice idea bro.
thanks bro. may mga kasunod pa yan na video, pati yung DIY ko na oven pang bake nung na powder coat. busy lang sa work kaya hindi ko pa na e-edit video clips.
R u provide electrostastic liqvid paint sprey gun project
@@riyenpatel3628 Hi. I have never tried electrostatic charged liquid paint though I read about it.
This is very good and educational.
Thanks. Hope you see the other video updates in my channel about this project.
@@DIYPhil I Did. Done watching them.
Thank you very much. Would you show me how to make some of coating paint powder at home,please?
Hi. Yes I will upload some more videos including the actual powder coating I do at home with my homemade equipment. please stay tuned.
#homemadepowdercoating
#DIYpowdercoating
you can get a air gun on amazon with a flexible hose will work better
thanks. this is the earliest version. I actually already got that 3/8" flexible hose for my setup now.
can i use this instead???? can i convert it to powder coating gun?
yes you can try. this is the first one I actually made and it does work but with some limitation. it is cheap to make and good for experimentation.
How the powder will be charged without current
On another video, I show how I make the power supply to produce electrostatic charge of the gun.
Boss upload m nman yung ginawa mo n powersupply para mgkaidea lahat hehehe salamat boss
yan po yung sa power supply. ua-cam.com/video/8Nywhih1QJQ/v-deo.html
no electrical charge?
Yes there is. The construction of the power supply is on another videos. do check these out:
ua-cam.com/video/8Nywhih1QJQ/v-deo.html
ua-cam.com/video/jJm6EpnzTnQ/v-deo.html
@@DIYPhil You should have put all in the same video tbh.
Hi Phil, where are you located in Thailand?
Hi Mike. I have a house in Sattahip. But I can either be in Songkhla or Phitsanulok because of work.
@@DIYPhil OK you are too far from me. I live in Bangkok.. Would be nice to meet with you if you are ever in my area. Please let me know.
Sir saan kayo bimili ng powder coating paint.. salamat po
Chemrez tech Inc. Sa bagumbayan libis quezon city look for Jen aquino
Sir anu po yung sa likod ng L bow epoxy po ba yan?
oo boss epoxy. yung parang clay.
Ilan horse power compressor at ilan laman ng tangke psi at output ng powder coating si?
eh nasa 10 psi lang ang kailangan sa pag spray ng powder. kahit yung maliliit na compressor kayang kaya. yung isang version nga sinubukan ko blower lang eh. tingnan mo to: ua-cam.com/video/V3WGkSkLMIg/v-deo.html
New sib sir.... Thanks for sharing
May mga kasunod pa yan na video sir, panoorin nyo kasi mas updated. Ngayon may ginagawa ako update nmn ng piwer supply
@@DIYPhil magkanu if bibili ako nang gawa na boss...
Ai from Indonesia tolong
Komponen alat nya tuan
Plis
Anong part ng DT project gagamitan ng powder coating?
yung cylinder block, cylinder head, chassis, tank, swing arm. bale halos lahat po ng part na yari sa metal. yung right crank case cover din sana kasi iyun yung unang unang nagagasgasan ng pintura, kaso napinturahan ko na ng spray paint.
@@DIYPhil yung powder coat daw sa hi temperature at regular ay magka-iba. Nag inquire ako dito sa amin pero specialty nila ay mga rims. Yung sa makina lalo na sa mga mainit na mga part special powder coat ginagamit.
@@idselseno2306 thanks sa info. nakabili na ko ng powder, black. nung bibili ako 2 yung pamimilian. yung mas mahal ang binili ko na made in USA daw. tapos mas mataas yung curing temperature kaya baka yun na yung special powder. pero check ko pa rin sa supplier.
A
my kit b nbbli
Puro mga recycled materials lng po yan. Madali lng yan gawin
Sir paano po yung swing arm wala po kame malaki oven, pwede po ba init ng araw para matuyo?
Hindi pwede. Nasa 200'c ang init para makapag powder coating. At powder po yung paint, tuyo po yun.