Hey Jubee, I’ve got a 68 Camaro that getting new firewall and cowl, full floor and truck, new outer rockers both rear quarters and a roof skin. What advice could you give as to the order I should follow to cut and replace these panels? I was leaning toward starting at the cowl and firewall
Question Jubee. Are the upper fender bolts(the ones you measure to get your 18 7/8) off from one side to the other? If I measure from the floor up to the top bolt hole I get a different measurement. Any advice?
Jubee , You where recommended by a friend to watch your content . I'm working on a rare 68 Camaro and ordered a complete floor pan frame rails and trunk pan from RDS How ever it has many Issues . I did post a video if you have time to view it . Thanks in advance C1
Thanks for your help! Also - the 18 7/8 measurement, does that go to the top of the upper cowl at the front OR at the hump created around the fender bolt hole located on the cowl?
Did you watch the video? I showed you where. It comes from flat surface where frame bolt goes in on torque box to the top of cowl. Yes the top of hump created where fender bolt goes.
Jubee, puhleese make a complete video! You know so much! Thanks! 67 SSRS CAMARO
You show stuff that matter to the finished job! Getting it all in the right place and how! Damn good video!
Hey Jubee, I’ve got a 68 Camaro that getting new firewall and cowl, full floor and truck, new outer rockers both rear quarters and a roof skin. What advice could you give as to the order I should follow to cut and replace these panels? I was leaning toward starting at the cowl and firewall
GOT IT, thank you.👍🏻👀
Funny- I just had the same question about the fender bolt hole dimension.
Jubee is a VERY patient person. Bet he gets this question a lot.
Jubee - I posted a recent video of the work you helped me do…gave you a couple of shout outs!
Awesome. Thank you. Hope your build is going well
Question Jubee. Are the upper fender bolts(the ones you measure to get your 18 7/8) off from one side to the other? If I measure from the floor up to the top bolt hole I get a different measurement. Any advice?
Do you have any drawings for that floor jig?
Jubee , You where recommended by a friend to watch your content . I'm working on a rare 68 Camaro and ordered a complete floor pan frame rails and trunk pan from RDS How ever it has many Issues . I did post a video if you have time to view it . Thanks in advance C1
Yea none of thier stuff is anygood. I will go check out the video and see what I can tell. I am sorry that you are having issues.
@@aMAYSingMetalWorks I have done a few Chevelles this is my first camaro rebuild metal wise . Thank you for your help
@@aMAYSingMetalWorks well today i was test fitting my cocktail shakers and the mounts are way off as well : (
Thanks for your help! Also - the 18 7/8 measurement, does that go to the top of the upper cowl at the front OR at the hump created around the fender bolt hole located on the cowl?
Did you watch the video? I showed you where. It comes from flat surface where frame bolt goes in on torque box to the top of cowl. Yes the top of hump created where fender bolt goes.
@@aMAYSingMetalWorks - yup! Got it! Thank you again!
Was one of these a Right Hand Drive firewall?
Gotta love those ratchet straps. They can get you out of a lot of problems. Dynacorn better than AMD? Is that just firewalls or all metal?
AMD is better with most all the parts. Just right now the dynacorn Firewall is better. I am going to try to get with them about this issue
Jubee How can I contact you
Jubeemays@gmail.com and I'll get you my number
@@aMAYSingMetalWorks sent you an email