Nkapaka informative ng tutorial sir. Dmi q nkuhang bagong teknik. Kaso parang nacra nyo pa ung isang clip lock dun sa may power box ng epson naputol eh. 😁. S kbilang bnda Parang nanuod din aq ng palabas ni chaplin. Wlang script at dialogue. Hihihi. 😁✌️
Saludo talaga ako sa mga magaling mag ayos ng mga electronic good jod engineer your new friend her from red ninja team hoping you will visit my house too
Sir what was the voltage output of the power supply, and the 2transistor you said is it the 2 big component at the back of the board? and where the power ic located sir?
The Epson L3100 does not turn on. F1, A2222 and C6144 are working. The button and loop are also working. The power supply gives voltage to the board. The voltage on the button is not stable, about 1.5V. Disconnecting all the cables except the effect button is not the case. I reflashed. What else can be tested to revive the printer?
so ano po yung may problema sir? ang power supply ba or yung switch? tinest nyo lang ata wala naman repair nangyari. and pag cut sa video then magic na on na. 😅
Good day! I had a minor problem on this case na reheat q po yung mainboard. Ok lang po ang power supply. Pero sa ibang na repair q ng Epson L3110 same problem no power, nagpalit aq ng transistors A2222 at C6144 at nag ayos naman po. Another scenario po pwde thin masira ang power IC and also fuse (F1). Hindi q na videohan ang ibang troubleshooting na ginawa q. Hope nasagot q po ung mga katanongan nyo. God bless.
so anong nangyari sir? ano sira sir? ano gagawin? kalikot lang nmn nakita ko.. ganon ba yong pag fix ng printer? kalikotin lang? ang title kasi how to fix..
same issue sa epson L3110 ko. no power pero after unplug replug ng mga ilang beses, nag-o-on naman sya. mukang nagpapahiwatig na ata ung sira ng printer ko. di ko rin nakita ung repair boss. ano po mismo sira nyan? ano po mismo yung ni-reheat nyo? paano po ung re-heat process? cguro maganda kung lagyan mo ng content kung ano mismo ung nasira, pano nagawa, bakit nangyayari tong ganitong sira, at pano maiiwasan. TIA
Salamat sa pag comment. First thing to do, you need to clean the printer using brush and blower is applicable. Next do some testing to diagnose the problem. Then in my case I tried to reheat the mainboard and solved the problem. If the problem is still no power, do check the fuse, Power IC and the Transistor ICs. Then if you find out busted ICs, then try to replace new one, you can order online. If you want immediate solution, you can replace the mainboard that can also order online. Maybe from my next video tutorial I will show on how to replace ICs for no power. Thank you for your comment. God bless.
Paano po gagawin sir kapag halimbawang may kumislap o nagspark sa likod ng printer doon banda sa saksakan ng power cord sa likod. Nangyari siya pagkasaksak ko outlet.
Thank you for your comment. In my case sir pwde pang ma reheat ung mga pyesa in main board. Most probably pag No Power ung dalawan Transistor ang nasira. You can order it online.
sir good day po..yung epson l210 printer ko po nung nilinis ko po yung printerhead then pag balik ko po..pag open ko po ok pa nag power tapos gumalaw pa ang cartridges then ilang minuto lng po bigla nlalang po namatay ang power.ano po kaya posibleng nangyare..ayaw na mag on ng power..thanks po sa sagot
Thank you for your comment. Troubleshooting tips for no power: 1. Check the power source, 2. Check the power cable and make sure properly connected. 3. Check for any loose connection inside the printer, such as flex cable and other wire connected to the main boar. 4. Mainboard problem, maybe the power IC or the fuse.
Good day! Thank you for your comment. Common problem for this kind of printer L3110 No Power problem. First you need to check the power adopter. Then check the mainboard and try to hot air or use soldering iron. If the problem is the same, maybe some of the IC's or Transistor (A2222 and C6144 )are damage. Try also also check the fuse (F1). Hope I can solve your problem.
Sir ano Po ba itsura ng fuse nya? . Na try ko na Po reheating board, na On sya pero pagkatapos ko ma assemle ayaw na naman mag ON, Kaya baklas na naman ako ,re heat uli, nag ON na naman, pero pagkatapos maassemble ayaw na naman mag ON
Tanx for the message. Tangalin mo yong power supply at gamitan mo ng blower, para matagal ang mga langgam. Kung wlang blower gamit kalang ng paint brush.
Kulang po ng naration, sana all engineer para maintindinhan proseso niyu po 😄✌️
Hi Sir Roncat! wow, marami ka pong matutulungan na mga teachers nito at mga students lalo na sa panahon ngayon.
Galing po kapatid talented super galing mo po all the best po GOD bless
Nag tester lang naayos agad ang printer what a nice video 😅😅
Reheated mainboard. Minsan pag d madala ng reheat, needed to replace ICs, Power IC, or maybe the fuse. Pwd din kung malaki budget replace mainboard.
Very smart of you engineer fixing this epson
Very informative.thanks for sharing this tutorials content.nag iwan na po ng maagang pamasko
Nkapaka informative ng tutorial sir. Dmi q nkuhang bagong teknik. Kaso parang nacra nyo pa ung isang clip lock dun sa may power box ng epson naputol eh. 😁. S kbilang bnda Parang nanuod din aq ng palabas ni chaplin. Wlang script at dialogue. Hihihi. 😁✌️
iba talaga ang galing mo lodi... how to be you po.
You are a legend engineer, you did a great job. Helpful blog, keep it up.
Restored, it's ready to work again. Great job sir!
thank you boss ok na more power sa yt channel mo
You're very creative thanks for sharing us your knowledge Sir Engr.fullpak watching from France
Salamat Sir EngineerFix Dagdag Kaalaman.
Galing nyu tlga sir engineer fix!
Salamat po ng marami sa pag share, malaking tulong po ito lalo na sa mga guro natin ngayon na gumagawa ng mga modules. Resbak ko po ito na
Thanks for sharing this video... This is the problem i encounter sometimes in my printer... Your video will be my guide in fixing it...
Good job Sir, 100 points ang grade mo kc ang galing2 po.
Good job sir.. you are very talented 😍
What was the issue? You repair switch or power supply?
Power jud kaayo ka bai sa pag repair ug mga printer ba. Keep vlog and share your ideas.
Very helpful thank you for sharing this
Great job sir & thanks for sharing👍
Saludo talaga ako sa mga magaling mag ayos ng mga electronic good jod engineer your new friend her from red ninja team hoping you will visit my house too
Wow! Kamaayo moayo nimo Sir sa printer. Good job!
This is very helpful content thank you for sharing po.
Thanks sir.
Natawa ako sa ipis.😂
another great and informative content
Wow sosyal to ah grabi congrats
Very informative tutorial thank you
A skillful Engineer is here! Thank you Sir for this vlog💞
Sir what was the voltage output of the power supply, and the 2transistor you said is it the 2 big component at the back of the board? and where the power ic located sir?
salamat sa pag share nito malaking tulong
Sana may step by step na narration kung panano ginanagawa, hindi puro sounds lang background.
oo nga e, parang midali lang
@@francisjimiera1808 tama, sana din pinakita panu inopen yung printer hehe
Ty for sharing sir, next time sana ibahin title kc misleading, sir dapat: Watch me fixing
Thanks for sharing the engineer
Thank for sharing this it real help
Hi po idol her na me fullpack support sayo kapatid..god bless
Thanks for sharing your video sir..
New friend here.. sending my support and great kindness
ganun pla un pag ayos salmat po keep vloging
Hi there
Can you the different voltages that should come out of the power supplu
I have
Red 42
Blue 40
Yellow 0
Is that normal?
salamat sa pag share po, keep vlogging po :)
Reheated?
Ano po ba issue dun boss?
Yung power button ba sira? or yung battery pinalitan ng bago?
nice info. but your music is louder than your voice
Alin ang inayos mo di nman nakita namin
yes fixing is hard for others..
How to open the printer you did not show it to your video
Thanks for sharing. Stay safe
The Epson L3100 does not turn on. F1, A2222 and C6144 are working. The button and loop are also working. The power supply gives voltage to the board. The voltage on the button is not stable, about 1.5V. Disconnecting all the cables except the effect button is not the case. I reflashed. What else can be tested to revive the printer?
so ano po yung may problema sir? ang power supply ba or yung switch? tinest nyo lang ata wala naman repair nangyari. and pag cut sa video then magic na on na. 😅
Good day! I had a minor problem on this case na reheat q po yung mainboard. Ok lang po ang power supply. Pero sa ibang na repair q ng Epson L3110 same problem no power, nagpalit aq ng transistors A2222 at C6144 at nag ayos naman po. Another scenario po pwde thin masira ang power IC and also fuse (F1). Hindi q na videohan ang ibang troubleshooting na ginawa q. Hope nasagot q po ung mga katanongan nyo. God bless.
so anong nangyari sir? ano sira sir? ano gagawin? kalikot lang nmn nakita ko.. ganon ba yong pag fix ng printer? kalikotin lang? ang title kasi how to fix..
Thanks for sharing sir
bakit naka faced mask ka Engr. Fix?hehehe,e nasa loob ka naman?nasira mo pa yung lock ng power supply ng printer?hehehe
Mukhang ang hirap nman po yan wla ako patience sa ganito heheh. God bless
gulantang ako sa paipis sir , but then good job po
Thanks sir your vidio
good pm po sir saan Po shop nyo dalahin ko Po epson ko salamat po
Sir, are l315 and l360 supply same or not?
I guest they are different based on their form factor. Same voltages but the design of power supply case is different.
Sir can you help fix my printer? epson L3210 no power on
Sorry Epson l3111 turns on and off automatically how can I fix it
same issue sa epson L3110 ko. no power pero after unplug replug ng mga ilang beses, nag-o-on naman sya. mukang nagpapahiwatig na ata ung sira ng printer ko. di ko rin nakita ung repair boss. ano po mismo sira nyan? ano po mismo yung ni-reheat nyo? paano po ung re-heat process? cguro maganda kung lagyan mo ng content kung ano mismo ung nasira, pano nagawa, bakit nangyayari tong ganitong sira, at pano maiiwasan. TIA
Sir pwede po malaman ang iyong mga range sa pag check?
Salamat sa pag comment.
First thing to do, you need to clean the printer using brush and blower is applicable. Next do some testing to diagnose the problem. Then in my case I tried to reheat the mainboard and solved the problem. If the problem is still no power, do check the fuse, Power IC and the Transistor ICs. Then if you find out busted ICs, then try to replace new one, you can order online. If you want immediate solution, you can replace the mainboard that can also order online. Maybe from my next video tutorial I will show on how to replace ICs for no power. Thank you for your comment. God bless.
After water splash i cannot turn on my epson printer. Please help
pag cut sa video ayus na!!!! hahaha
Switch po ba ang issue sir?
You have a good skill engineer but hopefully next time you have to remove your face mask to make you more comptable of what you are doing..
Hi po, pag nabaso po ung printhead and nag no power, maayos pa po ba?
salamat po
Mga magkano po paayos ng printer?
Paano po gagawin sir kapag halimbawang may kumislap o nagspark sa likod ng printer doon banda sa saksakan ng power cord sa likod. Nangyari siya pagkasaksak ko outlet.
I am having the same problem.....plz explain more
Explain q po sa next video tutorial. Salamat po.
Bkit nag open kana sir ng housing baka cord lng pala sira... Sana una test jan cord
Show us properly how to open tray/cover
Paano sir pag nagpalit na ng board at power supply tapos umilaw at namatay din. Saan kaya cause nun para ma sira board?
Sonar video dicho ki vabe machin open hoy
Ang nakita ko lang po nagtanggal at nagbalik ng screws, nagcheck continuity at voltage pero wla ako nkita na inayos
Sir natanggal po ung 3 white cables na nakaconnect sa power button kaya di mag on. Paano po uto ibalik?
sir same issue po ng l3110 ko..ano po ginawa nyo po?
Thank you for your comment. In my case sir pwde pang ma reheat ung mga pyesa in main board. Most probably pag No Power ung dalawan Transistor ang nasira. You can order it online.
ganyan din po nangyare sa epson l3110 namin, may patay na daga at puro langgam po sa may bandang power supply 😢
Saan po shop nyo
Mindanao po ma'am.
sir good day po..yung epson l210 printer ko po nung nilinis ko po yung printerhead then pag balik ko po..pag open ko po ok pa nag power tapos gumalaw pa ang cartridges then ilang minuto lng po bigla nlalang po namatay ang power.ano po kaya posibleng nangyare..ayaw na mag on ng power..thanks po sa sagot
Thank you for your comment. Troubleshooting tips for no power: 1. Check the power source, 2. Check the power cable and make sure properly connected. 3. Check for any loose connection inside the printer, such as flex cable and other wire connected to the main boar. 4. Mainboard problem, maybe the power IC or the fuse.
why only epson has "No Power Issues" Other printers no such problems ? Bad Design?
Some epson printers are designed not for heavy duty, but due to our needs we didn't think for it's proper operation.
Sir mera l3110 pinter hai or power se on nahi ho raha hai
Good day! Thank you for your comment. Common problem for this kind of printer L3110 No Power problem. First you need to check the power adopter. Then check the mainboard and try to hot air or use soldering iron. If the problem is the same, maybe some of the IC's or Transistor (A2222 and C6144 )are damage. Try also also check the fuse (F1). Hope I can solve your problem.
Sir ano Po ba itsura ng fuse nya? . Na try ko na Po reheating board, na On sya pero pagkatapos ko ma assemle ayaw na naman mag ON, Kaya baklas na naman ako ,re heat uli, nag ON na naman, pero pagkatapos maassemble ayaw na naman mag ON
Have to lower music so that we can hear your voice 👍🏼😁
ganon pa la pag aayos . babaklasin tapos i aasemble ulit . tapos gawa na. wahanjo di manlang nag paliwanag kung ano sira .
nag tester kalang repair na. hanip...
Tanx for the message. Actually sir gumamit aq ng hot air at soldering iron. Test q din ung mga pyesa. Buti lang nadala pa ng reheat.
Paano po boss kung no power pagkatapos ng power cleaning epson l3110
Sir mas okay ata inalis mo ang mask
Who out the background music I want to kick on aaaaas, this video is for music or technical support?
anu po naging problem nan... got the same printer, wala din po power
bakit po after ikabit yung powerbox, wala pa ring ilaw yung power. samantalang sabi nyo nai reheat nyo lang yung pcb ng powerbox, then umandar na ulit
Depende kc sa problem, in my case pwd pa ma reheat. Pag di na pwd ma reheat. It might be some problem such as transistor IC need to replace.
bhai mera printer on nhi hota hai kya kare samaj nhi aata hai
Good day, please translate to English, sorry but I can't understand.
You didn't even state the what is the problem
sana sir, sinabi ninyo kung ano ang nakita nyong problema at kung ano ang ginawa nyong solusyon🙄
Sana sir di mo na po nilagyan ng bg music, di po kasi maintindihan yung sinasabi mo.
Sir, paano po kapag pinasok ng mga langgam yong power supply?
Tanx for the message. Tangalin mo yong power supply at gamitan mo ng blower, para matagal ang mga langgam. Kung wlang blower gamit kalang ng paint brush.
Nabuksan po namin gang sa loob ng P/S, andaming patay na langgam. Thank you video.
Sir ano po solution pag nag on tapos off agad
Maybe in your cable wire. Please check power cable connector.
anu sira ng printer
Please sir help
Hahahaha.. Parang nag demo lang kung paano mag tanggal.. Sana nag explain ka kung anong sira.. Mukhang wlang sira yong prenter mo.. Jejeje.. Joke
Oo nga hindi inexplain kung ano yung sira at paano iSolve. Brand new naman printer
Patamsak po