@@zeemixvideos6485 पावर वापस आने पर इसकी टाइम काउंट वैल्यू होल्ड रहती है या रिसेट हो जाती है (जीरो हो जाती है ) p 1.1 सेटिंग में >ट्रिगीर इनपुट रुककर चालू होने पर ? क्या मुझे इन्वर्टर से सप्लाई रखनी होगी, वैल्यू होल्ड करने के लिए ?
पावर वापस आने पर इसकी टाइम काउंट वैल्यू होल्ड रहती है या रिसेट हो जाती है (जीरो हो जाती है ) p 1.1 सेटिंग में >ट्रिगीर इनपुट रुककर चालू होने पर ? क्या मुझे इन्वर्टर से सप्लाई रखनी होगी, वैल्यू होल्ड करने के लिए ?
Sir mery incubator mey timer jb thori dair chalta h fr wo sec mey a jata h or sec down hony lgty Han zero hny k bad time again apni limit mey phnch jata h ot tray rotate ni hoti kya masla h bta dain
Bhai motor ko aap ne supply 220 volt ka dena hai relay ko aap ne sirf switch k tor par use karna hai {Normaly close aur normaly open par aap ne 220 volt kay wires( jo k eik 220v supply se aata hai aur dosra wire jo k moter se ata attached karnay hai )aur neutral direct motor par jae ga Agar samaj nahe arahe to channel ko subscribe kardo aap k leye special video bana k upload kardonga
bro i dont know where u from but if you are from pakistan you can find it on daraz. pk hallroad. com and their are many other websites if you are not from pakistan you can find it on international website
@@techzen186 to bhi teek hoga bus rotat karna hai jitna bhi ho nichay wala side lana chaheye aur ooper wala nichay Sorry mein ne 360 bol deya hai lekin 180 he karna hai
P1: Trigger signal, the relay is on "OP" time, and then disconnect; Within the "OP" time, proceed as follows: 1. P1.1: signal is triggered again, invalid 2. P1.2: signal is triggered again, re-clocking 3. P1.3: Signal is triggered again, relay is disconnected, stop the clock; P-2: Trigger signal, after the "CL" time is off , the "OP" time is on. When the timing is completed, the replay will be disconnected; 4. 5. P3.1: Trigger signal, after the "OP" time is on, the "CL" time is off, then cycle the above actions. If trigger signal within the loop, the relay will be disconnected and stop the clock. The number of cycles ( "LOP ") can be set. 6. P3.2: No need to trigger the signal after powering up, the "OP" time is on, the "CL" time is off, then cycle the above actions; The number of cycles ( "LOP ") can be set. 7. P-4: Signal holding function. If the signal is triggered, timing is cleared, the relay remains on; when the signal disappears, the relay will be off when the "OP" time is over; if another signal is triggered during timing, timing will be cleared. 8.
Are bhai bahot hi achchha video banaya hai bhai bilkul sahi se samjhaya hai umne..Very Good. Kya tum mujhe help karoge ki mujhe agar ishe Microwave Oven me Lagana hai to ishka ishtemal kese kar sakta hun me...mail adddress hei " dharmendra.jhaveri@gmail.com
Omg ty ty ty so much....itni acche se samjhane ke liye. Connection dikha dete to aur v accha hota
Thanks for watching next video me pora incubator bananay ka tarika sikaonga aur connection bhi kar kay dika donga thanks for commenting
Bohat acha samjaya hai yar Alah aap ko kamyabi ata kare dunia main bhi aur akhrat main bhi
Ameen bohot shukria bhai
@@zeemixvideos6485 पावर वापस आने पर इसकी टाइम काउंट वैल्यू होल्ड रहती है या रिसेट हो जाती है (जीरो हो जाती है ) p 1.1 सेटिंग में >ट्रिगीर इनपुट रुककर चालू होने पर ?
क्या मुझे इन्वर्टर से सप्लाई रखनी होगी, वैल्यू होल्ड करने के लिए ?
Very good video. Sajid from Rawalpindi
thanks
Pathan bhai zinda baad kia achi tarah samjaya hay buht khoob der kha thumsup
Thanks
Dera dera manana please channel subscribe kae❤
Kamal ki information 👍 hai Khan ji...zabardast.
Bohot bohot shukria
Nice explain
Thanks 👍
Asalamvalekum bhai kiya ye 2gante ke liye on .our parment of rak sakth hai
Bahut helpful video hy ye thank you
Thanks bro
@@zeemixvideos6485
Bhai our satings ki videos ka link bataiye ga
Bhai mera channel visit kijeye
W1209 ke settings
Aur homemade incubator k baray mein aapko videos mil jae ge
Good
Verry good
excellent explaination and video
Thanks bro
Great job 🎉❤
My timer is showing countdown in increasing order like : 12345...
I want reverse count down like 54321...
Any settings for this? Please
Bhai aapka knowledge batane ka tareeka bahut hee kabile tarif , ye upkaran kaha se purchase kare pls tell me.
thanks bro
bhai online search karo mil jae ga
aap kis country se ho
wow
superb
MashaAllah
new frnd here
Have a Blessed day
Thank you for watching g
Kindly subscribe
Best information
vhai thank you
thanks for watching bro
One time kitni motor connect kar sakte he ?
Bro isme ghanty k hisaab sy setting kr sakte hn jesy ek light hai wo subha 7a.m bajay on ho jaye or sham ko off hojaye 7p.m ?? Ye possible hai
No
Good work brother
Thanks bro
Fine
पावर वापस आने पर इसकी टाइम काउंट वैल्यू होल्ड रहती है या रिसेट हो जाती है (जीरो हो जाती है ) p 1.1 सेटिंग में >ट्रिगीर इनपुट रुककर चालू होने पर ?
क्या मुझे इन्वर्टर से सप्लाई रखनी होगी, वैल्यू होल्ड करने के लिए ?
I want to continue the timer till the Trigger pressed On, please help
i like it
thanks
Good 👍
thanks bro
A DC motor of 24 v or 48 v.
Or any ro booster pump operate ho sakta ha
Please btayee
g hosakta hai
Thanks good work
Sir tell me forward and reverse becoz egg turned need it
Bha ap ne jo arduino egg incubator bnaya tha un ki coding shear nhi ki plz wo shear kardy
Bhai email send karo us par send kardonga
Thanks for watching💞
????360 munit KHATUM HONY k bad kia seating dobara KRNA HOGi .yea EIAK hy bar KRNA hogi
eik he bar karna hai
sir ji muje 1h to 300h ka timer bana na he
Great job can you tell me how to reset the timer
Thanks for watching bro kindly subscribe my channel thank u
Bro aap q reset karna chahtay hai yane koe masalaa hai circuit mein ya koe aur waja hai
Timer display sahi data ha lakin kabhi work karta khabe nahin
Sir mery incubator mey timer jb thori dair chalta h fr wo sec mey a jata h or sec down hony lgty Han zero hny k bad time again apni limit mey phnch jata h ot tray rotate ni hoti kya masla h bta dain
timer ko reset karay aur pir dubara se setting karay agar pir yahe masala aata hai to pir timer ko change karay
@@zeemixvideos6485 reset kesy hna bta dain jazak Allah
Turner. Moter kiwair keder lagani hai...? Meri moter220ac hai timer 12v hai
Bhai motor ko aap ne supply 220 volt ka dena hai relay ko aap ne sirf switch k tor par use karna hai
{Normaly close aur normaly open par aap ne 220 volt kay wires( jo k eik 220v supply se aata hai aur dosra wire jo k moter se ata attached karnay hai )aur neutral direct motor par jae ga
Agar samaj nahe arahe to channel ko subscribe kardo aap k leye special video bana k upload kardonga
seconds count 1 2 3 4 5
seconds count 5 4 3 2 1
Is there any setting for this?
Sorry i dont understand
Same problem...
Want reverse countdown like 5 4 3 2 1...
Kindly share the link to buy the product
bro i dont know where u from but if you are from pakistan you can find it on
daraz. pk
hallroad. com
and their are many other websites
if you are not from pakistan you can find it on international website
Daraz
What happened if Ac voltage is 300 volt .
supply 12volt hona lazmi hai
controle aap 300 volt bhi kar saktay hai
relay k uper rating lika hoga
Egg kitna turn krna chahiye half ya full
360 bro
@@zeemixvideos6485 full 360
Agr 180 kia jaye to ???
@@techzen186 to bhi teek hoga bus rotat karna hai jitna bhi ho nichay wala side lana chaheye aur ooper wala nichay
Sorry mein ne 360 bol deya hai lekin 180 he karna hai
Mujhe iske settings samaj nhi aari hai
Mujhe isko 5min on karna hai fir off permanently kaise karu settings plzzz help
Whatsapp +923080440995
Bhai mera timer opposite work kar raha hai. Open time py off rehta hai or close time py on ho jata hai
Long press on up or down button position will be reveres at F1 or F2
How do I do the micro seconds setting
Bhai only seconds and minutes ke setting ho sakte hai
Brother ye kitny egg Wala incubator hai
ye sirf eik timer aap is se jitna banana chahay bana saktay hai
What will be it's life if we on/off 9 times per minute.
Bro life not changes with on off life of a circuit id directly proportional to current and voltage
Voice buhat slow he bro apki
Full video
Price and availability pls ?
Please check online in your country
Flipkart se Aaj hi purchase Kiya hai 270 me
Lop is not set brooo minits converts nahi he
Help bhai mujse ye shet nhi horha he
Bhai kia masala araha hai
Bhai P 3.2 kyun rakhna hai ??
P1: Trigger signal, the relay is on "OP" time, and then disconnect; Within the "OP" time, proceed as follows:
1.
P1.1: signal is triggered again, invalid
2.
P1.2: signal is triggered again, re-clocking
3.
P1.3: Signal is triggered again, relay is disconnected, stop the clock;
P-2: Trigger signal, after the "CL" time is off , the "OP" time is on. When the timing is completed, the replay will be disconnected;
4.
5.
P3.1: Trigger signal, after the "OP" time is on, the "CL" time is off, then cycle the above actions. If trigger signal within the loop, the relay will be disconnected and stop the clock. The number of cycles ( "LOP ") can be set.
6.
P3.2: No need to trigger the signal after powering up, the "OP" time is on, the "CL" time is off, then cycle the above actions; The number of cycles ( "LOP ") can be set.
7.
P-4: Signal holding function. If the signal is triggered, timing is cleared, the relay remains on; when the signal disappears, the relay will be off when the "OP" time is over; if another signal is triggered during timing, timing will be cleared.
8.
@@zeemixvideos6485 thank you for replying in detail.
Price
Aap kahan se ho bhai
Pakistan kohat sa
Whatssap chak kar
Are bhai bahot hi achchha video banaya hai bhai bilkul sahi se samjhaya hai umne..Very Good.
Kya tum mujhe help karoge ki mujhe agar ishe Microwave Oven me Lagana hai to ishka ishtemal kese kar sakta hun me...mail adddress hei " dharmendra.jhaveri@gmail.com
sound problem vaia!
Bro sound is ok
teri wajha se mera 2.5 lac ka laptop jal gaya
Kis waja se jal gaya
Short circuit karo to usb port jal jata hai laptop to nahe jalta😂
Laptop mein q lagaya mein ne to laptop k baray mein bataya bhi nahe
Koe nahe yar dosra lain laingay ab karo subscribe
bhai koi pata ni me na laptop usb port sa lagaya but laptop on he ni hu raha ab