Great video! We have been dealing with a problem in a CTG 1200A ATS with the MX150 controller. The thing is, we set up the everything and genset run every test fine from the controller including load test, no load start, etc. The thing is that when we shut down the utility to test like in a real life situation: 1) I takes 1 exact minute to close the start relay, even when the start delay is set to the minimum time. 2) When it finally starts, as soon as the generator runs, the start relay opens and turns the genset off, and closes and open again and again until when stop it manually. 3) I’m not very familiar with the MX150, but the controller screen is supposed to turn off when the utility goes out? Any input on this will be appreciated!! Thanks 🙏🏻
have you tried setting the engine start for something like 10 seconds? you may have lost the coin cell battery, power down the ATS, and remove the back cover form the controller and you'll see it. lastly and most likely the logic is corrupt, if it is send it to these guy's www.flightsystems.com/ i use them a lot, i think the last one we did cost about $550
Hi chainsaws and generators. I’m trying to figure out where to connect my “remote start” wires coming from my backup generator to the automatic transfer switch mx150. Based on your video. I just need to connect my two wires to the P relay on terminals 1 and 2? Great video by the way buddy!
I HAVE A TRANSFER EXACTLY THE SAME, I HAVE A PROBLEM, THE ACTUATOR ONLY RECEIVES VERY FAST PILSES, BUT IT DOES NOT CHANGE FROM SOURCE 1 TO SOURCE 2, AND THE DISPLAY TELL ME "MACHANICAL FAILURE" " EXPECT: SE" " ACTUAL: SN" CAN YOU HELP ME PLEASE. TANK YOU.
Yeah, power down the swich and see if it moves freely, not binding up. Check to see if the coil has power while transferring, if so the coil maybe bad. Check the resistance of the coil.
Great video! We have been dealing with a problem in a CTG 1200A ATS with the MX150 controller.
The thing is, we set up the everything and genset run every test fine from the controller including load test, no load start, etc.
The thing is that when we shut down the utility to test like in a real life situation:
1) I takes 1 exact minute to close the start relay, even when the start delay is set to the minimum time.
2) When it finally starts, as soon as the generator runs, the start relay opens and turns the genset off, and closes and open again and again until when stop it manually.
3) I’m not very familiar with the MX150, but the controller screen is supposed to turn off when the utility goes out?
Any input on this will be appreciated!! Thanks 🙏🏻
have you tried setting the engine start for something like 10 seconds?
you may have lost the coin cell battery, power down the ATS, and remove the back cover form the controller and you'll see it.
lastly and most likely the logic is corrupt, if it is send it to these guy's www.flightsystems.com/
i use them a lot, i think the last one we did cost about $550
Hi chainsaws and generators. I’m trying to figure out where to connect my “remote start” wires coming from my backup generator to the automatic transfer switch mx150. Based on your video. I just need to connect my two wires to the P relay on terminals 1 and 2? Great video by the way buddy!
Hey Chainsaw and Generators can you show how to program the MX150 to run under gen load for a few hours?
Is the P relay take power from the controller? Can you explain how the SCR get signal from controller?
Hey I get a question
interesting, but i wished you had talked a little slower and clearer.
I HAVE A TRANSFER EXACTLY THE SAME, I HAVE A PROBLEM, THE ACTUATOR ONLY RECEIVES VERY FAST PILSES, BUT IT DOES NOT CHANGE FROM SOURCE 1 TO SOURCE 2, AND THE DISPLAY TELL ME "MACHANICAL FAILURE" " EXPECT: SE" " ACTUAL: SN" CAN YOU HELP ME PLEASE. TANK YOU.
Yeah, power down the swich and see if it moves freely, not binding up.
Check to see if the coil has power while transferring, if so the coil maybe bad. Check the resistance of the coil.
@@chainsawsandgenerators9952
I also have an mx150.
Seems Older one - with mechanical failure- SNO SE
SNO SEO
ANY INPUT WOULD BE GREAT
@@me2ten294 its in the micro switches beside the contactor, probably one has failed
Hello I have a GE zinth controls mx150
You are totally wrong body the transition coil its not 480 ..you start the video back ward's jajajaja
Micro switches....check.
with most transfer switches micro switches control everything..
was that you looking into my house last night?
@@chainsawsandgenerators9952 you are low on milk to go with the cookies..