Can u make a video showing us how to make that pushing tool u used to push the button please, part list and how to make it properly aligned, thanks and awesome video, new sub
@@ottowhack9248 I think the fifth grade is dangerous for a 9 mm bullet, as there is a possibility that the bolt barrel will explode , cuz once i asked a glock company about theirs opinions on 8.8 grade they didn't recommended to even to made a barrel from a bolt 🔩 for 22 lr bullet it's okay any other calibre , for safety no
Have a look at these barrel tests by the Idahoan Show Aluminum .45acp ua-cam.com/video/eku8TNTGQ2s/v-deo.html Plumbing Pipe .40s&w ua-cam.com/video/9loXa-H0crE/v-deo.html Grade 5 bolt .40s&w ua-cam.com/video/D43ZeYu9dnM/v-deo.html DOM Tube .50ae ua-cam.com/video/RdKFE0AbbcY/v-deo.html
@@garfieldcz3415 I used a 23/64 drill bit. The actual measured diameter was .355". I found that the shank of a drill bit is not hard enough to survive the job. You might remember from the video that the rifling it produced was very rough and the button was ruined in the process. That original video and a photo showing the condition of the button are still on my instagram under "ottowhack".
Really good, man.
He's so strong he cut the bolt with a single stroke each time
Can u make a video showing us how to make that pushing tool u used to push the button please, part list and how to make it properly aligned, thanks and awesome video, new sub
What length of the whole like what bullet or caliber is needed
Ótima ideia.👏👏👏
Sir tutorial how to make barrel
Where can i buy that type of bolt , what grade ???
This was a 3/4-10 thread Grade 5 bolt from a hardware store.
@@ottowhack9248 I think the fifth grade is dangerous for a 9 mm bullet, as there is a possibility that the bolt barrel will explode , cuz once i asked a glock company about theirs opinions on 8.8 grade they didn't recommended to even to made a barrel from a bolt 🔩 for 22 lr bullet it's okay any other calibre , for safety no
Have a look at these barrel tests by the Idahoan Show
Aluminum .45acp ua-cam.com/video/eku8TNTGQ2s/v-deo.html
Plumbing Pipe .40s&w ua-cam.com/video/9loXa-H0crE/v-deo.html
Grade 5 bolt .40s&w ua-cam.com/video/D43ZeYu9dnM/v-deo.html
DOM Tube .50ae ua-cam.com/video/RdKFE0AbbcY/v-deo.html
@@ottowhack9248 What size drill bit did you use for rifling button in your (now deleted) 9mm pistol video?
@@garfieldcz3415 I used a 23/64 drill bit. The actual measured diameter was .355". I found that the shank of a drill bit is not hard enough to survive the job. You might remember from the video that the rifling it produced was very rough and the button was ruined in the process.
That original video and a photo showing the condition of the button are still on my instagram under "ottowhack".
Meu COLEGA VC NA TERRA DO TIO SÁM ache muito bacana a sua capacidade. Porém vc tá ANOS LUZ Q FAZER CANOS .
TheIdahoanShow😄
that looks cheap to try
To much work. Everybody have a tool in toolbox for riffling 22lr. But they dont know it😎
Can you open my eyes?
Instead of a press, pound the button through with a hammer.
Cual?
Please tellme !
AnalWrench
👎👎👎
German?