Thanks so much. This really helped me. I was activating the coils in the order 11, 10, 9, 8 from following other programs but it didn't work. Using your 8, 10, 9, 11 worked perfectly. Why does a sequential order not work?
Hi, Love your video... I'm very new about this kind of programming... I have a question: is necessary to connect the ground and the 5v between Arduino and the driver?
Could you please give me some advice? Is it possible for the engine to work even without a computer? I need it to keep spinning at 20 rpm. It is possible?
Hello dear bro, i followed this video step by step but when i send the code to my board, the board disconnect from the PC. notice that i have "Az-Delivery ESP32 Wroom" . i thought that the Stepper motor absorbs the energy. to solve this problem i brought an external enrgy source (Breadboard Power Supply), finally worked well but, i got the same problem that "Rajat parkkal" got, the motor don't rotate to the other way i mean the negative orientation. i'll be thankful to help us solving this problem. *Notice: i'm fresh in Arduino and i have no idea befor this is my first steps on this world.
when i put a negative number the motor is not turning the opposite direction whereas going in the same clockwise direction towards the angle. Is there a solution??
Sir please make a more video one motor 180 degree rotation after stop after number 2nd motor run 3 round after stop after 3rd rotation 4 pound after 1st motor rotation reverse 180 degree
Same question - in the arduino tutorials it shows defining the pins in numerical order - 1,2,3,4 while you are using 1,3,2,4 Can you explain the difference? Did the stepper library change?
Incredibly simple explanations, which is very difficult to find on the internet these days. Well done.
I am so thankful that you like it 😊
Clear and concise. I set my stepper while watching your video and it worked 🙂, thank you for sharing
Glad it helped!
THIS IS THE BEST VIDEO I'VE SEEN ABOUT HOW TO USE ANY ARDUINO DEVICE!!
Really appreciate your interest
Most of my parts were different but the tutorial was so good I could make it work. Thank you!
First video where is all explain step by step - thanks, it works well
Glad it helped!
Thanks so much. This really helped me. I was activating the coils in the order 11, 10, 9, 8 from following other programs but it didn't work. Using your 8, 10, 9, 11 worked perfectly. Why does a sequential order not work?
Nice, very helpful. I agree with the guy just below me, simple explanation, again, very helpful.
Great to hear!
Very well explained! Thank you, just wanna know if using that code, will the motor continue rotating endlessly ?
Help! My setup only runs clockwise and doesn't reverse! Everything is just as you wrote it, Paul. Also, I can run mine without the power supply.
same as mine
Hi, Love your video... I'm very new about this kind of programming... I have a question: is necessary to connect the ground and the 5v between Arduino and the driver?
Yes, absolutely
How can we control the stepper motor using RC remote
Could you please give me some advice? Is it possible for the engine to work even without a computer? I need it to keep spinning at 20 rpm. It is possible?
probably yes if you have an arduino battery.
Doesn't the starting current affect the arduino power pin connected to the driver??
It should not tolerate more than 20mA
Very nice! Thank you for creating such a helpful video. Your explanations were very clear for a beginner like me.
Thanks for your interest, and I hope you are doing well.
I tried with this but my stepper motor doesn't work , one more thing do I need to use the way you have used some pin on it
Whats the maximum speed and torque of this motor?
great video
Thanks!
Thank you🙂
No problem
what to do if need the motor to rotate in constant rpm ?
could you give me the code?
Hello dear bro,
i followed this video step by step but when i send the code to my board, the board disconnect from the PC. notice that i have "Az-Delivery ESP32 Wroom" .
i thought that the Stepper motor absorbs the energy.
to solve this problem i brought an external enrgy source (Breadboard Power Supply), finally worked well but,
i got the same problem that "Rajat parkkal" got, the motor don't rotate to the other way i mean the negative orientation.
i'll be thankful to help us solving this problem.
*Notice: i'm fresh in Arduino and i have no idea befor this is my first steps on this world.
You need a separate supply for stepper motor your facing that problem due to current limitation
how to move it faster? Its a bit slow
How to do 90 degrees?
please give the link or code
please just add a link for the code
It never works just showing us it'
is it possible to control the motor without the driver?
No
Thx it works.
No problem
when i put a negative number the motor is not turning the opposite direction whereas going in the same clockwise direction towards the angle. Is there a solution??
استاذ شاكر هي الحاجات دي بتتجاب منين؟؟
ممكن من موقع amazon
بالنسبة لنا في تونس هناك متاجر تسوق لها أو من خلال مواقع بيع موجودة في تونس.
Sir please make a more video one motor 180 degree rotation after stop after number 2nd motor run 3 round after stop after 3rd rotation 4 pound after 1st motor rotation reverse 180 degree
why does INT 1 and INT 2 stay on after the first command and only turn on after a reset?
Plss can to tell me why the order is 8,10,9,11
Same question - in the arduino tutorials it shows defining the pins in numerical order - 1,2,3,4 while you are using 1,3,2,4 Can you explain the difference? Did the stepper library change?
Can I change the rotation of the motor manually??
Yeah you could control it using push-buttons, potentiometer, or joystick 🕹....
can u teach how to do stepper motor analog rpm gauge diagram and thank you
Your Gode erro from myStepper ! Tell me please
ممكن تعطيني الكود لان كل ما اكتبه يطلع غلط انا سويت نفسك بالضبط
It doesn't work
'mySteper' was not declared in this scope
When I compling
What I make mistakes
THANKS SO MUCH
No problem