Low-Tech circular saw blade sharpening jig!

Поділитися
Вставка
  • Опубліковано 24 гру 2024

КОМЕНТАРІ • 44

  • @MakerBoyOldBoy
    @MakerBoyOldBoy 21 день тому +3

    Excellent video. "Dropping On" in Yanklish speak is a Plunge Cut. He is exactly correct as to its danger. A friend lost his thumb doing this technique. I'm subscribed.

  • @jordanadams4595
    @jordanadams4595 7 місяців тому +4

    Thanks for all your generous vides, Steve. Your woodworking channel is one of, if not the most informative on UA-cam and deserves many more subscribers. Keep up the great work!

    • @SteveMaskery
      @SteveMaskery  7 місяців тому

      Thank you very much indeed. It's taken 16 years to get to 18K subscribers...

  • @martinlouden9005
    @martinlouden9005 8 місяців тому +5

    Great info Steve. That's the only jigajig I'll get these days!

  • @MrPatdeeee
    @MrPatdeeee 8 місяців тому +4

    As always, Steve KNOWS how to do it! Thank you. For you are one of the Best DIY'rs! Keep it going in! 😀

  • @Randy.Andy.
    @Randy.Andy. 4 дні тому +1

    This guy is a pro. This jig is very good. I have always been concerned about the dust from carbide blades. Rather than use a file, is it possible to use a sharpening stone if the stone fits between the gullets ? Thank you for teaching and sharing.

    • @SteveMaskery
      @SteveMaskery  4 дні тому

      Yes, I don't see why not. But my diamond fine is very fine, so I use that.
      I hope you make this, you won't be disappointed.

    • @Randy.Andy.
      @Randy.Andy. 2 дні тому

      @@SteveMaskery Thanks for your answer. Which diamond file are you using ? Where can I get it. Yes, I will make the jig.

    • @stevemaskery3568
      @stevemaskery3568 2 дні тому

      @@Randy.Andy. I thought it was unbranded, but there is a very faint embossed name on the side - DMT Duofold. It doesn't say what grit it is. I've had it for years.

    • @SteveMaskery
      @SteveMaskery  2 дні тому

      @@Randy.Andy. I thought it was unbranded, but there is a very faint embossed name on the side - DMT Duofold. It doesn't say what grit it is. I've had it for years.

    • @Randy.Andy.
      @Randy.Andy. День тому

      @@SteveMaskery thanks

  • @MCsCreations
    @MCsCreations 8 місяців тому +2

    Thanks for the tip, Steve! 😊
    Stay safe there with your family! 🖖😊

  • @simonfraser1624
    @simonfraser1624 16 днів тому +1

    Can I use this jig for high speed steel blades, or do I need to jig an angle to the top block?

    • @SteveMaskery
      @SteveMaskery  16 днів тому +1

      Yes you can. But normally you would only touch up the face. But if you really do want to file the back, adjust the jig so that the back of the tooth is flush with the top of the jig and use the file flat rather than upright. HTH.

  • @frankherring6253
    @frankherring6253 8 місяців тому +3

    Very nice Steve! Thank you!

  • @henrywilliams1965
    @henrywilliams1965 11 днів тому

    Way back when i took my hollow ground planer blade to a guy who sharpend blades at his saw shop. When i got home with it i found that the dumb ass had put a set in it. It tore the wood all to heck. Will never do that again. Ive found that with the carbon tooth blades that mostly you just need to keep them clean. Just get you some simple green and a soft brass or nylon brush. Clean them in a five gallon bucket top, works really well. Rinse them of and make sure their good and dry to prevent rust.

  • @davidpitts9086
    @davidpitts9086 7 місяців тому +1

    Off to the shop I go...Thank you

  • @eduardo_2805
    @eduardo_2805 8 місяців тому +2

    Nice and simple! Thank you

  • @magnatimberworksclinthurst6209
    @magnatimberworksclinthurst6209 8 місяців тому

    Great video
    Call me tight but I’ve been sharpening jigsaw blades. Had a load of vinyl click flooring to lay, hammers the blades.

  • @Woodgate425
    @Woodgate425 8 місяців тому

    Yet another great jig Steve and one l will definitely be having a go at. I wonder how many swipes I’ll get singing the first few lines of Dad’s Army 🤔🤣

  • @dougfrazer9202
    @dougfrazer9202 Місяць тому +1

    Steve: Pretty much all the TCT Saw blades here in N.Z. are either ATB blades, or, if you find one, they are hundreds of dollars for a single blade. My question is: can an ATB blade be reground to a "flat cut" blade with a Diamond file, or Diamond grindstone? I know where I can use one of these Grindstones if careful resharpening of the blade is possible. By the way; a great video you have just put up here. 🤠

    • @stevemaskery3568
      @stevemaskery3568 2 дні тому

      I'm afraid I don't know, you'd have to ask your saw doctor. If it is any consolation, they are getting harder to find over here as well.

  • @ryanlemons7831
    @ryanlemons7831 7 місяців тому +1

    Ah this is great sir! Thank you!!

  • @DavidEdgeTripeBroadcasting
    @DavidEdgeTripeBroadcasting 7 місяців тому

    Splendid! Now what do you use for getting resin off sawblades? I can't believe there isn't something better and cheaper than the Axminster stuff which seems to be ethanol at a higher price than Calvados

    • @SteveMaskery
      @SteveMaskery  7 місяців тому

      I don't have much trouble with resin, TBH, but when I do I use WD40 and a toothbrush. Oven cleaner is popular, but someone told me it doesn't do the welds any good.

    • @DavidEdgeTripeBroadcasting
      @DavidEdgeTripeBroadcasting 7 місяців тому

      @@SteveMaskery I'll give it a go, thanks. Thinking about it, I don't suppose you can weld carbide, so perhaps it's brazed. And if there's aluminium in the braze, caustic will certainly get up to no good.

    • @scottrhoades9056
      @scottrhoades9056 Місяць тому +1

      Rockler and other companies sell a citrus based cleaner (judging by the smell) with a round plastic bin that holds the cleaner and the blade to be cleaned. I place my blades in the bin and add the cleaner to soak for 5-10 minutes depending on the pitch saturation on the blade. Using a brass or nylon toothbrush sized brush, it takes 10-15 minutes to clean both sides. I then filter the solution before returning it to the container. I imagine over time, the solution will become saturated with suspended resin however, after six years I have had no reduction in cleaning efficiency.

    • @Bob_Adkins
      @Bob_Adkins 21 день тому

      I've had great success with spray-on oven cleaner (mostly lye, aka sodium hydroxide). Use it outside with safety glasses and rubber gloves.

  • @crossgrainwoodproductsltd9230
    @crossgrainwoodproductsltd9230 7 місяців тому

    Some very good tips within your video. As simple as it may seem to other's, the use of a magnet to mark your stating tooth is brilliant to me. Yes you can use a permanent marker or even a dot of enamel paint and re-use that same dot for every sharpening, but eventually it will wear off. A magnet solves that issue and can be stored with the jig so it's not lost when stored.
    I also like the different spindles/ arbors you made for each size blade. A clever idea. The rest of the jig for me, just seems over built. If sharpening with a diamond file, all you need is two pieces of wood to clamp the blade between to keep it up right. You can add a hinge at one end and hook and eye to keep the 2 boards tightly closed around the blade. You could take it another step by using a router circle jig and route grooves deep enough so as you spin the blade to the next tooth it will move freely. For me, I modified a pretty beat up, antique handsaw clamp. I paid $5 for it at a flea market, knowing it was not in good enough condition to restore and sell as I do with most acquired Antique tools if not for my personal collection. I remove the rust from the frame and parts, then repainted it to prevent further rusting. I added strips of wood to the jaws to prevent any damage to the teeth and added to partial round grooves in the strips for each size blade I sharpen. The smallest being 115 mm or 4.5"
    I will be tapping a drilled hole in the frame to accommodate your various sized wooden spindles so the blades will have something to spin on.

  • @SteveMaskery
    @SteveMaskery  Місяць тому

    Hi Doug, I'm afraid I don't know, it's more of a question for engineers. Sorry I can't help further.

  • @andreasbentz6106
    @andreasbentz6106 8 місяців тому +1

    Excellent Jig Steve. But please wear a mask and wash your hands - even if the air is not filled with dust, there will be toxic tungsten-carbide debris around.
    BTW - what sort of file do you use? Did I miss that in the video?
    Cheers
    Andreas

    • @SteveMaskery
      @SteveMaskery  8 місяців тому

      Hi Andreas, good advice about the handwashing. The file is a flat diamond file. I don't know the brand, it's not labelled and I've had it for donkey's years. I did mention it in the film but it would be easy to miss, I guess.

    • @andreasbentz6106
      @andreasbentz6106 8 місяців тому

      @@SteveMaskery Thank you for the info on the file, Steve. In addition to washing hands, I would also put that file now in quaratine and use it only for this particular purpose. I am maybe a bit nervous about cross contamination (since I am a microbiologist), but better safe than sorry.
      Have a nice weekend!
      Andreas

  • @davidpitts9086
    @davidpitts9086 7 місяців тому

    Just wondering, what is the name of the file you are using, please and thank you.

    • @SteveMaskery
      @SteveMaskery  7 місяців тому

      I thought it was unbranded, but there is a very faint embossed name on the side - DMT Duofold. It doesn't say what grit it is.

    • @davidpitts9086
      @davidpitts9086 7 місяців тому

      @@SteveMaskery Thank you

  • @ronnyrider722
    @ronnyrider722 2 місяці тому

    top class !

  • @koningbolo4700
    @koningbolo4700 13 днів тому

    13:24 I do have an alternative way to count 31 odd strokes, but it may make me sound quite racist...which I am actually not...

  • @LarryB-inFL
    @LarryB-inFL 8 місяців тому

    ARE YOU KIDDING????? Every blade I own varies in the set and rake of the carbide tips, plus *many* blades are ATB, where there are THREE different angles. Your jig wouldn't work on ANY of my blades.

    • @SteveMaskery
      @SteveMaskery  8 місяців тому +11

      I don't understand you. The top bevel is irrelevant, this only touches the face. Now if you have alternate FACE bevels, and such blades do exist, then this would not be the jig to use (although making a bespoke sliding fence for an AFB would be very straightforward). I don't think you understand what this jig does.

    • @rafezetter8003
      @rafezetter8003 8 місяців тому +5

      You don't need to sharpen the top bevel. As for alternating face bevels, you can add a removable guide to the correct angle for both faces, then sharpen all the faces of one angle, then swap angle guides and then do all the opposing faces. This entire jig can be altered to suit your needs, just a little 3 dimensional thinking required so I don't see a problem here, but feel free to move along to your next YT video and keep paying to have blades sharpened.

    • @gcarson19
      @gcarson19 8 місяців тому

      Lacks the ability to understand the jig so leaves a whiny, griping comment instead...

    • @CredibleHulk10
      @CredibleHulk10 29 днів тому +1

      Larry, you need to calm down, sir. My goodness.

    • @Bob_Adkins
      @Bob_Adkins 21 день тому

      @@gcarson19 Probably throws his dull blades away because he doesn't know how hey work.