Complete Guide for 15A 400W MOSFET AOD4184A to control motor or load
Вставка
- Опубліковано 6 лип 2024
- This video explains using MOSFET as a Switch or as a PWM driver to control motor.
Here is better version for Higher voltage or Higher current • How to use Mosfet Opt...
The best thank you for me is to not skipping ads and Subscribing 🔔 to my channel, and clinking 👍 the video. It is greatly appreciated. 🔔 😊.
I will reply to all Subscriber's 🔔 questions. So make sure to Subscribe.😊 .
** Purchase Arduino Start Kit **
Amazon USA: amzn.to/3z88F9G or just UNO board amzn.to/3aY7KOL
Amazon Canada: amzn.to/31an88J or just UNO board amzn.to/3pYxSNN
Amazon Europe (all Europe): amzn.to/3pMCHge or Just UNO board amzn.to/2PgGItD
AliExpress: s.click.aliexpress.com/e/_9uc7Xe
Banggood: www.banggood.com/custlink/3GD... or UNO board www.banggood.com/custlink/vKm...
eBay: ebay.us/B1JWLi
***** Purchase Authentic Arduino Uno from ***
Amazon USA: amzn.to/2KApAwK
Amazon Canada: amzn.to/37LZ8sW
All Europe Amazon: amzn.to/36YDSzn
Chapters of this video. Click on time to go:
00:00 Start
01:37 Introduction
05:00 Datasheet
05:46 Code explained
08:23 Wiring explained
08:52 Using Mosfet as switch
10:40 Higher current demonstration
16:30 MOSFET as swatch code
Get Arduino code and datasheet: robojax.com/L/?id=181
Learn Arduino in 30 Minutes (video): robojax.com/L/?id=135
Tutorial by Ahmad Shamshiri form Canada
****************************
Learn Arduino from a proven instructor with 100s of projects, code, wiring diagram in structured course in one place. Purchase Arduino Course at Udemy.com : robojax.com/L/?id=153
****************************
If you found this tutorial helpful, please support me so I can continue creating contents like this. Here is PayPal link paypal.me/robojaxTV
Get early access to my videos by becoming my Patreon and and have your name mentioned at end of very videos I publish on UA-cam: robojax.com/L/?id=97
If you want to learn Arduino from proven instructor on **Udemy**: bit.ly/rj-udemy
Follow me on Facebook robojaxTV
Follow me on Twitter: / robojaxtv
Follow me on Instagram: / robojax
Tutorial by Robojax.com
Get other projects code and learn Arduino
robojax.com/learn/arduino
#robojax #robojax_relay #robojax_wifi
#robojax #robojaxMOSFET
*** AFFILIATE PROGRAM ***
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. - Наука та технологія
It is an art to explain some complicated things THE EASY WAY.
Thanks!!!
You are welcome. I am glad you found them useful. The best thank you for me is to Subscribe 🔔 to my channel and thumb up the video. It is greatly appreciated. 🔔 😊.
THANK YOU! It has been extremely hard to fine a good explanation of these and your video summed it up quite well.
You are welcome. You haven't subscribed to my channel. The best thank you for me is to subscribe to my channel and thumb up the video. It is greatly appreciated. 🔔 😊
Excellent overview. Many solderable inputs are no longer confusing. Good job.
An excellent demonstration of all the facets of this tool! Thanks for sharing your knowledge, Ahmad!
Thanks for watching
If my college project gets complete it's because of this video.....
Thank You for heavy load drivers...
Happy to help
Thanks a bunch Robojax, in return for your good presentations, I don't skip ads even in your other videos as gratitude
You are welcome. Thanks for your support.
Finally someone who explains it in details! Thank you! :D
Glad it was helpful!
Thanks you do such a great job explaining as well as showing!
You are welcome. Thank you for not skipping the ads and keep watching them. This will help me a lot.
Very good details and demonstration, thx.
As a "Switch" use, turn it ON with 4.5v for the automotive 10.5v thru 15v range with a thermistor monitoring the Fet temperature, steady state at 70f (120f for Arizona) ambient for at least an hour.... Although for a common ground automotive use, a P-Channel high side mosfet is more practical....
Thank you for sharing in this detail
VERY nice video and explanation. Thumbs up!! I had a strange situation with mine. When I used Ground from my board (24V, stepped down to 5V with 7805), the module failed to work! Yet, when I just used the gate PWM signal, with NO ground attached to the small voltage connections, it works! I'm not very experienced so I'm probably doing something wrong!
Very nice, just want I wanted. I am looking to control a 70w (12v) pump, so I think this will be perfect.
Excellent video. This is how it must be made. TX 4 sharing
Glad you enjoyed it! Please subscribe. It is appreciated.
Wow, excellent, thanks.
And your English is so good!
Thank you too!
Hi sir, excellent tutorial? Can I use this module to maximize the voltage from an esc? I mean without that the motor reaches the max speed 7.2v but when I push a button on arduino it lowers the maximum voltage to 4v for example. The main issue I see here is the change of polarity (to go backwards with my device) can you suggest something for a bidirectional regulator where the vin is came crom an esc?
Hello Sir can I use this for esp32 cam tank robot. I feel the wheel are very slow and sometimes unresponsive. Im using the l293d bridge motor drive. Not sure if it's d battery or not. Will the Mosfet help utilise the battery more and also make the wheel faster and more responsive?
Good stuff man
great video!
@robojax Thanks for the cool video. I'm a beginner and don't really understand such subtleties. Please tell me, can I connect a solenoid as a load and control it? And also if the solenoid winding suddenly burns out and a short circuit occurs, what will happen to this module?
Hello sir, I loved how you are good at teaching. I have the same module. I am designing a buck converter and when I connected this module to my circuit. It didn’t work. What should I do ? It works when I connected a small resistor to the module but when I connect it to the a converter, it didn’t work. HOW COULD I CONTROL THE MOSFET ? PLEASE HELP ME ! Thank you and stay safe 🙏🙏🙏
as usual. an excellent video :-)
Glad you enjoyed it
Really informative presentsation - Thanks a lot
You are welcome.
0
I wld really like to thx to u Mr. ... cuz when ever I want to curious some item about electromechanics, you Sir on the line which gives sufficient/above (such as gives:... ooohhh I got it [what else :) ] information/data. I felt to give furthermore-thx so plz keep go on..! U r u in a business to give big support which help ppl like me who else doesn't know really anything about the core subject of this comment..!
you are welcome. I am glad you found it useful.
Thank you! Good video! The only things is that you don't really need a diode in antiparalell since the mosfet has one incorporated. As long as you don't go over 20 amps you are fine. Acording to the datasheet
You are welcome. That is a good point I ponder upon. Thanks for the tip.
Thanks dude
Thank you for a good video of this module. i went and bought some.
But i Do find they get extremely hot.
I'm using a 11.1 lipo battery at 2000Ah
I'm using it for a small engine and so the Mosfet is being used for the ignition coil
So I have the Mosfet connected from the Arduino and is connected with the Lypo 11.1 and the mosfet is connected to a Ignition Coil that has a spark plug that generates the Spark
But after 5 seconds it gets extremely hot but other devices don.t get hot.
so the coil is drawing to much
i dont know what i can do apart from adding some heat sink but i do think it can be sorted via another way but don't know
Any help from any one I will be very grateful
Hi, just suscribed to your channel. Quick question: If I want bidirectional control on the motor, how could I achieve it using the HW-517 module? Thanks!
Can I use potentiometer to drive the gate of the mosfet? Thanks for the video.
Can this module be used in the car to run up converter 12 to 30 volt. The controller to take a signal from remotecontrol pleyar 12 volt. The idea is to embed up converter 12 to 30 volt + TDA7498E. The controller should start up converter
I'm just curious. . . Can this module be used on an AEG airsoft?
I AM WORKING ON A PROJECT AND NEED YOUR HELP. I have a ZK-12KXV3 voltage regulator, a ZK-PP2K PWM and a X0029KL I DD Cycle Delay Drive Module. I am not sure how to wire the PWM to the driver to pulse a pancake coil. Can you help?
Hello. Nice explain. Thx. But, why when in serial monitor motor speed is 0, motor still turn, or lamp still glow? Why voltage go not to 0V? Thx for explain
The trigger, how much voltage can it receive?
Your videos are very informative. I watched your video on the E-switch. Does this module have an optocoupler like the E-switch?
Thank you Mike. I am glad you found them useful. No it doesn't have optocoupler.
Great video
You are welcome. Here is $200 Arduino course for free Arduino Step by Step Course (over 100 lectures) Starts here robojax.com/L/?id=338
What motor dc do you use
Nice one sir
Thanks.
This is so cool. I really need a help here. I want to change the polarity as well. Using a 12V-3A motor. Is there an h-bridge module of the same mosfet or should we make it by our self ? Or can you recommend another single channel h-bridge motor driver which is not very expensive. Thank you.. Cheers.
You are welcome. The mosfet have been used in chip to control motor but with 1A or 2A. There is L298N that can handle up to 4A www.sparkfun.com/datasheets/Robotics/L298_H_Bridge.pdf and module is sold on eBay or AliExpress and Amazon.
The Rigol visual interface is very interesting, can you tell us more about it in a separate video... I mean the hardware equipment and so.
Hopefully if I find time. I have it on my list to do a review of the Rigol Electronic load.
May I ask you a novice question, Sir? Is is alright to connect the (-) pole V- to the (-) of the load (out) such as motorcycle headlight? I'm going to use it in the motorcycle and all negative pole is connected. Thank you..
I had to watch the video to answer your question as it seems you've skipped the video. please watch from 8:45 (click on this 8:45) and you should know. your motor cycle light is a load. just see how to connect a load.
I check my duty cycle at the output keeps at nearly 100% regardless the input pwm duty cycle
Hello Robojax, I am very glad that I found this video of yours. I would like to to use this board to do 2s vape mod. I am quite concerned with the Rds(on). It is too high for the my application. the mosfets will heat up quite a lot for 20 - 30A amplication. Will it be possible to replace the mosfets with IRBL 3034? If so, will I still be able to control them using PWM? Thank you!
Hi, upon checking the specs of suggested mosfet it seems the IRLB should work. Both have VGS=20V and others specs should not matter in this application.
@@robojax Wow! I wasnt expecting a response from you this quick. Thank you so much, Robojax!
Hi Robojax. Thanks for a great vid. Could you use 2 or more of these modules in parallel to switch higher current or to keep the modules cooler when switching around 400W?
Yes you can .
@@robojax I bought a few of these and I'm putting a 350W resistive load through just one and it hardly even gets warm 🙂
nice. Do you need an arduino or can you just use apply a DC voltage from a battery to trigger the switch?
Yo switch you just need supply at input. But if you want to control the speed u need arduino. Must watch got all answers.
This video is super helpful! Question: I’m using a 12v lead acid battery, to control a DC motor. I’ve burned up 3 of these MOSFET modules. Do I need a resistor somewhere?
Hello, the battery voltage won't kill it. it is the amount of current (or power) that kills it when it is above the limit. See this module different version of this which is much better ua-cam.com/video/eqXaqRFAWrA/v-deo.html and there is resource page link to purchase it.
Could this act as a led driver and provide power for ~30V ~40W led ? (With a ~36V power source).
Thanks.
I have explained it. Watch this with more power ua-cam.com/video/G9uHVcITHf8/v-deo.html
Thank you for making this video. It's great. Quick question: What about reversing the motor? Does this motor driver support reversal?
Not by default, you could use multiple modules to make a full bridge. I think robojax has a video for that.
sir can i use this module as simple ON and OFF control for 12v , 12.3amp dc fan heater?...
Yes you can.
hi sir witch one is good MOSFET for switching AOD4184A or IRFR5305
also support for more voltage & ampere.
Hi, AOD4184A can handle Drain current 50A/40A at DS voltage of 40V and datasheet here www.aosmd.com/pdfs/datasheet/AOD4184A.pdf and IRFR5305 can handle -22A continuously DS Voltage of -55V See datasheet here www.infineon.com/dgdl/irfr5305pbf.pdf?fileId=5546d462533600a401535632522820ff and you will find the answer to all of your questions. Good luck
Wow, perfect video, covering a lot! One question, at 12:45 you say you can change polarity with 4 of those. Would you explain how please?
Thanks. that needs full separate video.
Sir i have to use this for 4 solenoids interface with arduino but this solenoids are operate one by one so I have to use solid state relay to fast switching operation so have to use this solid state relay so how many times this will be a off ,on in 1minute or 1
second
yes you can use two of this to connect.
Hello, would I be about to hook this up directly to an rc reciever?
Hello, no you can’t . This module needs clean PWM while the receiver has encoded different signal. I have not tested it but it will have unusual behaviour if you connect it. Try it. There is no harm.
Hi good explanation. I wonder if this device works really also at 3.3 V Vgs as they say .
Hi, Thanks. I have not tested it but it should work.
Can you put 2 of these in parallel to control a 60A charge ?
yes you can
Looking at a constant current. For. Solar battery to feed inverter
Can you connect more MOSFETs in parallel in order to get more current?
yes you can. If you use heatsink as I mentioned (I believe I mentioned ) you will have 2 or 3 times current than without heatsink.
Can I use ESP8266 with 3.3v logic also? Instead of arduino
Yes you can. I have provided the link to the datasheet in the description and the threshold voltage is 2.6V and it should work. Here is the link once again www.aosmd.com/pdfs/datasheet/AOD4184A.pdf
Hello. Very good explanation! Good job sir! One question.
You mentioned in your video that, if we have four of them we cloud control the direction of DC motor. But how to achieve that? As far as I check the VIN(in, out) is not controlled by MOSFETs only ground line is. So how to using four circuits like this address the direction of motor? Thanks in advance!
Hello and welcome. that is called full bridge. please watch this video to learn about it. ua-cam.com/video/PUL5DZ9TA2o/v-deo.html
@@robojax Thank you. Two more questions. First one about this module. Is it safe to put + (hot) wire to negative pole? To control + rather than ground connection? Is it safe for Source and Drain?
Second one: I'm familiar with H-Bridge concept but in this solution we must use two "P" and two "N" MOSFETs. Here we have only one type of mosfet. How to achieve H-bridge using four of this?
Hi Robojax ..Tell me if I am wrong but does 2 mosfets mean that this board has bidirectional control. if not why is there 2 mosfets? … also is there a circuit diagram for this board
Hi, perhaps you skipped the video. I just watched the video and I have explained it. I can't type everything there. Watch the video fully and you will get the answer.
thank you for the video, could we connect the RC receiver to the PWM and control it? thanks
Yes you can!
@@robojax thanks for the quick replay mate, I've tried, and I get only 0.8V when input from the receiver is 5V, I've connected the PWM to the white signal wire, am I'm doing somthing wrong? thank you
@@robojax ?
hi; at 12:46 looks like that the pwm input are wired into the 2 far side out pins? I have wired the two PWM terminal to the big J1 connector holes , the LED lights up but the motor is not turning , this motor used to work with the other controller ( the one with the pot included ,that you have show us in another chapter) ,can you please suggest what can be wrong?
thank you
We have power that comes to the mosfet. Then we have PWM signal that turns on or off the power. So you have to connect the power.
@@robojax yes I tried it outside and works, must have been a bad connection, thank you for the advice
Can you please explain how to connect a frequency generator module to the XLX?
Thank you
What is XLX?
@@robojax www.amazon.com/XLX-Transistor-Module-PWM-Regulator-Electronic-Switch-Controller/dp/B07ZHC5M7H
I’m trying to build a PEMF device using a Frequency Generator Module = XLX Mosfet Module = Out To Coil any advice on how to hook it up ?
Thank you
this is the same module. they just call it like that. I have no idea what kind of coil you use. I tested it so you know the maximum current. Remember if you use coil when the signal turns OFF, the energy with revers polarity from the coil is might kill the module.
Nice sir, can i use this for thermoelectric/peltier load?
Thank you. yes you can.
You can but efficiency will be reduced
Sir please tell me switching rate of this module that means this will be how many times off and on in one minute?or 1 second
it is in the delay() and if you want it faster, I have provided the datasheet. See it.
Sir, i wanna ask. I use the same mosfet and arduino uno. I'm trying to dim my lamp using the mosfet and LDR. The problem is only the mosfet get dimmed not the lamp. The lamp is still on while the mosfet got turned off. Am i doing it wrong? Thank you
What kind of lamp is it? You can use only DC bulb or DC LED light. Not AC household bulbs.
If the mosfet turn OFF, your light should turn OFF. So you are doing something wrong.
@@robojax oh i see. Yes i am using an AC lamp. I'm still kinda new on this stuff and is doing a project about adaptive lamp. Thank you for your help!
You are welcome.
hi again, how could we connect the RC receiver to the PWM and control it? I did that and it's not working, I've tried, and I get only 0.8V when input from the receiver is 5V, I've connected the PWM to the white signal wire, am I'm doing something wrong? thank you
please help. thanks
the receiver always outputs 5V. So I do'n how you measure it. This module can be easily with RC receiver.
@@robojax thanks for the reply, yes the receiver has 5V, I feed the input with 5V, to the PWM on the board I connect the signal white wire, and then the output is only 0.8V, do I need to connect any resister to the PWM? how to make it work? your responses will be highly appreciated...
Will the Mosfet be fully turned on when the trigger signal is only 3.3v?
I believe I have provided the datasheet in resources page. Look at it there should be table and graph.
Can I use a potentiometer to vary the trigger voltage and thus proportionately vary the output voltage to the load? I am just a beginner skill level with electronics. Thanks
No you can't. this a switch. either will turn ON or OFF. if you want to control a load, then use PWM like controlling the brightness of LED or speed of a motor you can very easily control the speed without changing the voltage. It is better and effecient. load is not controlled by verying the voltage.
@@robojax Thanks, this makes sense now that I think about it.
I am controlling motors with raspberry pi 3model B using relays but when operating other small sensors connected to raspberry pi i2c ports stopped working. Can you explain why this is happening?
I have not tested this with raspberry pi
Can I use two of those to control motor in Forward and reverse.
No. If you don’t need to control the speed then relay could be used. Search my channel I have video on that.
Can I also use this module for LED drivers, I have led strip 12 v 15A, my power supply is 12V, 20 A, I want to dim the LED strip
yes you can. LED strip and motor can be controlled the same way. Can you please post a new comment and tell me what kind of LED strip you have that needs such power? I don't understand why even people need to use LED strips. I have one at home in our kitchen which needs only 2A or 3A. I want to know and make video on that. Thanks.
@@robojax I am using to drive LED strip as well. My LED strip uses 12vdc at 2.6W per foot. I have 16 feet in one cabinet. If I open all 3 cabinets I have a little over 10A.
hello, i want to ask about this mosfet, is this mosfet can hold this? thankyou
Current 2A
Voltage: 12V DC
Initial suction: 20 (N)
Working voltage: 24V
I have provided the link to the data sheet. Check that
Can i use this to drive a Line output transformer?
this can feed DC current to a device with the current I tested. so it is up to you.
Is it okay if I add external diode between Vout+ and Vin+ in this module? Thanks
yes you can.
@@robojax Thanks for the reply and helpful. I just started learning some arduino stuffs. I am sorry for typing mistake, what I meant was external diode between Vout+ and Vout-, not between Vout+ and Vin+.
You can edit comment at any time. just click on the 3 dots. between output pins that goes to the mosfet.
this mosfet good for 12v or 24v inverter??
small cute and good for high amp
I believe I mentioned the voltage in the video. I don't remember.
Can it be used for an upstream car converter to run from a cassette recorder remote 12 volt out
I believe the test I presented show give you the answer.
@@robojax Pioneer remote control 12 volt make a circuit and put the module in the car and start the module up conwertor 12-14,2volt 15 amper to 24 volt 7Amper max amper. I think it will be thanks a lot for the video.
the reason I said that , I don't remember what happened in the video and in order to answer your question, I would have to watch the video and answer. So I suggested that you watch it. You can come to conclusion by looking at Maximum Current I have tested.
Can you control using a potentiometer?
yes you can. I just add it to my "to do" list.
Hi Mr. Shamshiri,
I want to use this module to control the speed of DC Pump 12V with the current 5A. I know from your video demo, that the module should be ok and can handle it. But I want to know further, if I use it for continuous current (5A) in SIX HOURS of an operational pump (without stopping), will the module still work well? I mean what about its temperature? Or can you give another recommended module for that purpose? Your suggestion would be helpful. Thank you.
salam alaikum, of coruse it can . 40A is continouse current at 100C and and 50A at 25C don't every trust free talk. Look at datasheet www.aosmd.com/sites/default/files/res/datasheets/AOI4184.pdf
@@robojax Wa'alaikumsalam. Thank you for your response. I'll go to try this module. One more question Sir, if you may. What size of the diode used in this video demo? 10A?
Yes 10A.
@@robojax Thank you Sir. May Allah Azza Wa Jalla bless you always.
hello everyone....i need it for 105vdc i'm afraid if i use it like that it may burn ...any suggestion thanks ?
Here is the the better option ua-cam.com/video/eqXaqRFAWrA/v-deo.html
Since the two are in paralel the D-S resistance is double for each MOSFET
Thanks
In 5:11 Vds max is 40V when Vgs is assumed to be 0 ?
You are welcome. Gate-Source voltage is your source voltage to the motor. VGS turn ON and OFF with PWM between 0 and 5V.
And what does 40V Vds mean?
Does this module can be use for solar light led light 1100 lumens?
to find the rate of an electronic switch like this, usually the current in Ampere is important then the voltage. I assume the voltage is low and the current for 1100 lumen is very low. this device can handle 15A and if voltage is 12V, then it would be like 180W and I am sure your 1100 lumens less than 50W. Check the information and if the current is less than 15A you can use it.
I need some help. My Mosfet drivers seem to work perfectly just like in the video, but then something happened and now my module outputs the same voltage as the input voltage without the PWM pin being powered, almost like it is short circuiting. Has anyone had any problems like this ? Please help if possible
I had the same issue. I found that a load needed to be put on the out put before the unit would put out the adjusted volts
can it run at 12V 1.5A constantly without a heat sink?
I can run a 24V 2A motor without a heat sink.
i have tried using same module to control motors ,as i increase load on motors ,it draws current around 3-4 amp and mosfet starts warming up ,i looked into data sheet it says Id is 50amp(Maximum) ?
HELP me with THIS ISSUE ...
thanks
Hi, when you said " looked into data sheet it says Id is 50amp" it show you have skipped the video as I have explained this. Please watch without skipping .
@@robojax ok
Hello I want to see a circuit of this Mosfet trigger switch drive
Please if u have it show me
It’s very important for our project
We r making the electronic device with pwm input signals and we need a higher power of this signals that’s why pwm amplifier needed
Thanks appreciate it
Hello, please contact me via robojax.com contact page and provide your email in the body of your text. I will contact you and collect the details then I will tell you the cost, write the code, make demo video and you pay only if you are satisfied with the demonstration video.
If I use 10S Li-ion battery power supply (36v), which when fully charged ranged mostly at 42v,
will it blow the mosfets?
This was great channel btw, just subscribed!
Thanks. I've shown the datasheet and I just checked it. 40V is the "Absolute maximum" meaning it blow anything above 40V. However you can replaced the mosfets with IRFZ44N. See datasheet for IRFZ44n here www.vishay.com/docs/91291/91291.pdf
@@robojax cool, thanks for the advice, appreciate that. 🙏🏻
Can we use this MOSFET as HIGH SIDE switch ?? Please reply
no you can't . on the high side, the Gate voltage needs be higher the source pin. when you have load of 12V on the source, then gate needs 12V+GSv, if GSv=5V, then you need 12V+5V=17V. for that reason you need gate driver chip which will take care of this for you.
Yet p type h ya n type mosfet module
it happens.
It is possible to change the direction of rotation of the motor?
no. this is half bridge. you need full bridge. Here learn about Half and Full bridge ua-cam.com/video/wn5D7j1ybxY/v-deo.htmlm40s
Can i use DRV8833 Motor Driver ?
a.aliexpress.com/_dWgC5TJ
Yes this is full bridge and you can control motor in both direction.
what is the name of windows application you are using?
which window? The first on is Arduino IDE a free program you can get from Arduino.cc and the 2nd, you can see the title Rigo Ultra Load. it comes with my Electronic Load (hardware).
I have a motor that works with 24v how do I tell the MOSFET to give 24v? Sorry if this is to o obvious I'm a beginner
Just connect 24v
@@robojax Thanks also why do I need to connect the diode when I use the motor?
Hi. Thanks so much and dear sir.
This module is only CW (clockwise) function, no has CCW (counterclockwise) function. I want to use module has two functions (CW, CCW) So I would like to know what's kind of it (my motors: max current 10A, 12VDC).
Note:
I have been using BTS7960 for controlling my motors with arduino. But because of expensive.
I'm not programmer, architerth, coder.
I'm waiting inf form you. Thanks
see this L298N ua-cam.com/video/wn5D7j1ybxY/v-deo.html
@@robojax Thanks sir reply. Yes off course L298N has two 2 functions (CW and CCW), But L298N module has max current 2A. I can not use L298N because my motors (7A - 10A).
search for the word PWM and you will see more than 10 videos and modules with very higher current.
@@robojax Honesty, After you reply. Sundden idea in my mind, and it's done well. Thanks you
how to use it for rotating motor reverse
if you want only CW or CCW direction just change the wire connection. but if you want to revers the direction of rotation, this module is not for that.
can this be used to a charger for 18650 batteries?
No. not at all. Watch this to learn about Lithium battery and protection ua-cam.com/video/0mOqpCfAdy4/v-deo.html or for 1A watch this ua-cam.com/video/3dwA8A8VrrE/v-deo.html
@@robojax But can this module adjust the PWM voltage for charging battery?
@@robojax can this module adjust the PWM voltage using Arduino?
someone please tell me the difference between this drive module and a 3 pin mosfet please?
this is driver module. A module is made of components and mosfet is one of the important components of it.
@@robojax WOW thank you for the prompt reply appreciated. Sorry just starting out, used 3 pin mosfets, with resistors and 1 way diodes, with12v. transmitter and receiver, to power 9v motor. But mosfets keep failing, i dont know much about electronics. Would i be better using these? instead??
pwm 50% duty cycle on me doesn't give me 50% of voltage input.. how could that be?
May be you have waring understanding of PWM. It is not redesign voltage at all. Voltage must stay constant.
@@robojax Okay your statement i totally correct. I forgot to mention that I add capacitor at the output an alas the voltage doesn't give me 50% of voltage input
can this be used to an airsoft gun?
It can be used with DC load and the current is important. You can't go beyond the load limit. I have explained and tested the load capacity of this in video. Please watch it till the end.
@@robojax i sent a message on fb. Do you reply there?
How to switch motor direction?
get different module. this can't do it. I have a lot of videos on that. search my channel.
I guess the motor supply ground is the same as the arduino supply ground ?
yes. Shared ground.
Please explain how to create an h bridge or reverse the direction of motor using MOSFET trigger switch. You can PM me