This video shows how to block the CKV line with this type of T-con and remove the bar lines. Tips and Tricks. Please like share and subscribe. thank you.
Hi engineer All ckv, s must be addressed through a flat cable to the board? The information between the two fields that are parallel to the address board
I have a very bad success rate on fixing Samsung panels with such a problem. It is the TU7000 series if you know them. The ones that the back cover has no screws.
Sir i have a question. I want to change pixels response time because its response is very slow and is bothering me when watching. Is there any trick with the components so i can modify then and improve it?
Picture drawn by 2 sets of ckv signals ...if one shorted...lines appear...seperated the shorted one by disconnecting it will let tv work show picture with reduced resolution ...the seceen will only work full resolution if both ckv signals are connected...but one ckv is shorted inside the lcd glass itself so no better solution but to disconnect it
Goodmorning po. May tanong po sana ako. Salamat po at nakita kopo ang tutorial nyo about po dito sa samsung same po sa tv po namin at nipagyan ko po ng papel sa mga ckv nya. naging maayus po at nagawa ko kaso po pag pinatay kona yung tv ay may mga guhit po horizontal sa may itaas ng screen pero after mga 15 minutes nawawala napo at ok napong muli ang picture pero kada patayin ang tv ganun na nman po at ok na maman after mga 10 to 15 mins. Ano po kaya ang sira. sana mabigyan nyo po ako ng advice. maraming salamat po....
Sharp 32le185 m in mirror mode(upside down)after burning bin file, no option in service mode,how to set it normal, how to enter panel setting, in service mode no panel setting option,
@@tevzTVTevatronics thanks for your support and help, didn't replaced the panel, set was in continuos on and off mode due to software issue, so burned the flash, with a bin file, but now set is ok but picture upside-down , i opened the service mode , but there is no option to panel setting, how to reverse it?
@@tevzTVTevatronics tried all 4 bin files available in internet, same problem, where is the panel mirror option , r how to open mirror option, I have saw your video of lamp error resetting service menu of sharp 40le185m 40 inch tv, in that service menu, no panel setting option , I have tried menu1147 , no use, it's a 2019 model, 32le185m, and 40le 185 m both have same motherboard
@@JeanDAVID Yes horizontal signals, but that does not mean it fixes only horizontal lines, but also the vertical lines, because if the horizontal signal is defective the outcome is vertical lines.
Hi, I have 42 inch A Samsung Plasma TV Has Two Vertical Thick black Bars On It, It Suddenly Came, each has a width about 1 and half inches, with about 20 inchesh interval, i cheched all the x board connection and reseated all of them but it won't go away, also cleaned the connections with spray an alcohol, but no locu, what should i do ?
@@tevzTVTevatronics what should i do ?! is it repairable ?! it's a complete deep black line, not a blinking one, does cof ic's are burnt ? is there a manual that i can read ? do you have any videos repairing one ? it's a plasma tv, it has two X boards, lef and right
U R master of the masters.
I learned a lot of informations from you .
Thank you very much sir.
lupet tlga sir
nice
Maestro thank you very much for the video 👍
watching master
Buenas tardes colega excelente vídeo saludos desde Argentina
I realy like your videos I have learn a lot whit them
Not like any other easy learn great time thanks
Thank you for knowledge 🇰🇪
V Good❤
you are a great master ❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤🎉🎉🎉🎉🎉
Mais um serviço rápido e preciso, parabéns 🇧🇷
Bahut achha video
Brilliant thanks 😊
süper
❤❤ thank you sir❤❤
❤❤u r great teacher❤❤
Good job 👏
Good. Thanks.
Bom conteúdo
Nice work sir
good
Bravo Tevz tv. Sayenizde yeni bir bilgi öğrendim. Sağlık ve huzur dolu günler.
This is great
Hallo Tevz sehr gut weiter so Gruß aus Greece F.G.Alex-Polis
Thank you for educating us but please can you make a video on how to know the T-con that support this kind of connection
yes will do
Same request here @tevz
Thank you sir for your knowledge that you share with us
It's my pleasure
Always tevz best repair man
Thanks Master.
Can you plz show us how modify crt tv power supply that uses ic 5Q0565tr by strw6053?
Regards
Desmond
From south africa
Thanks sir ..
Obrigado.
Hi engineer
All ckv, s must be addressed through a flat cable to the board?
The information between the two fields that are parallel to the address board
Very very nice sir soooooooper.
Sir I want Panasonic 32inc blank display solution please sir send one video sir.
I enjoyed to watch your vedio but it is not easy to repair tv. Some test point i understand ... More leasons again thanks..
Thanks for watching
Bonjour à toi excellente vidéo comme d'habitude 👍👍dis moi si mon commentaire et traductible d'en ton côté merci encore
Very nice vdo sir
Thanks and welcome
Thank you sir
Welcome
Good boy
Nice work. Is this a permanent fix, or will the problem come back later?
إن شاء الله
Hello Tevz, I hope all is well ❤
👏👏
Nice
Thanks
please answer my q, i really need to fix that tv.
👍👍👍👍
Hiii i'm new here i have problem in toshiba tv flash ic programe i have commented in that video pls reply
Sir I am from India
Please add subtitles for understanding easy.
subtitles are available, click CC on your browser and select your language.
I have a very bad success rate on fixing Samsung panels with such a problem. It is the TU7000 series if you know them. The ones that the back cover has no screws.
Most of them are the same problem panel.
Engineer, some repairmen announce that cutting off the information of a part of the flat will cause full hd movies to not be displayed, right
not all,
Hi tevz
Sir i have a question. I want to change pixels response time because its response is very slow and is bothering me when watching. Is there any trick with the components so i can modify then and improve it?
Slow motion image? There is a problem with the t con or the panel. Check vgh and vgl voltage.
Good morning sir from India
I don't understand how this works at all. I watched another video of similar fix and some of the color was gone.
Picture drawn by 2 sets of ckv signals ...if one shorted...lines appear...seperated the shorted one by disconnecting it will let tv work show picture with reduced resolution ...the seceen will only work full resolution if both ckv signals are connected...but one ckv is shorted inside the lcd glass itself so no better solution but to disconnect it
"working amazingly"
with half of vertical resolution..
What is buck Converter ?????
en.wikipedia.org/wiki/Buck_convert
Goodmorning po. May tanong po sana ako. Salamat po at nakita kopo ang tutorial nyo about po dito sa samsung same po sa tv po namin at nipagyan ko po ng papel sa mga ckv nya. naging maayus po at nagawa ko kaso po pag pinatay kona yung tv ay may mga guhit po horizontal sa may itaas ng screen pero after mga 15 minutes nawawala napo at ok napong muli ang picture pero kada patayin ang tv ganun na nman po at ok na maman after mga 10 to 15 mins. Ano po kaya ang sira. sana mabigyan nyo po ako ng advice. maraming salamat po....
Check mo kung tama yung na blocked mung line.
How many lines did you bloke it look like 18 or more ?
12 lines
@tevz
There is 8 ckvs and 2 are lc1 lc2
Whats the others 2?
@@abrarothay6874 VSS and VST
@@tevzTVTevatronics thank you
new subscribe new friends
Sharp 32le185 m in mirror mode(upside down)after burning bin file, no option in service mode,how to set it normal, how to enter panel setting, in service mode no panel setting option,
No mirror on service mode. That's will happen if the panel is replaced.
@@tevzTVTevatronics thanks for your support and help, didn't replaced the panel, set was in continuos on and off mode due to software issue, so burned the flash, with a bin file, but now set is ok but picture upside-down , i opened the service mode , but there is no option to panel setting, how to reverse it?
@@trinity3388 try other bin file
@@tevzTVTevatronics tried all 4 bin files available in internet, same problem, where is the panel mirror option , r how to open mirror option, I have saw your video of lamp error resetting service menu of sharp 40le185m 40 inch tv, in that service menu, no panel setting option , I have tried menu1147 , no use, it's a 2019 model, 32le185m, and 40le 185 m both have same motherboard
usualyy, black horizontal lines are solved by isolating CKV leads on the flat wire but here you have vertical black lines !!! How come ?
I think I never said horizontal lines on this video
@@tevzTVTevatronics cvk are horizontal signals ! how can you cure vertical black lines ?
@@JeanDAVID Yes horizontal signals, but that does not mean it fixes only horizontal lines, but also the vertical lines, because if the horizontal signal is defective the outcome is vertical lines.
Hi, I have 42 inch A Samsung Plasma TV Has Two Vertical Thick black Bars On It, It Suddenly Came, each has a width about 1 and half inches, with about 20 inchesh interval, i cheched all the x board connection and reseated all of them but it won't go away, also cleaned the connections with spray an alcohol, but no locu, what should i do ?
some vertical bar line can not resolve for this method,
@@tevzTVTevatronics what should i do ?! is it repairable ?! it's a complete deep black line, not a blinking one, does cof ic's are burnt ? is there a manual that i can read ? do you have any videos repairing one ? it's a plasma tv, it has two X boards, lef and right
@@bzfarbodjz I think it is the panel issue. not fixed by disconnecting the CKV lines.
Ur making fool
What you want to say adjectly?🙄
watching master