I just got this kit last week from Mr.King , I am astonished on how my Vulcan3 700 transformed, I was able to push NSA 43.5g slugs 6.35 @ 990 fps with almost no effort, the adapter for extra air tank volume 700cc is a must-have mod The regulator seat metal piece did clearly improve the fps consistancy Thanks Jeremy, Well done 👍🏻👍🏻👍🏻
@@salmanaljuaid6359 ولاتهون أخوي سلمان ، ركبت اسطوانة ٧٠٠ ، ورميت اربع محالات (اربعين رصاصة نيلسن ٤٣ قرين) على سرعة ٩٨٠ ونزل الضغط من ثلاثمية بار الى ميتين بار ، يعني بيكفيك الى ستين طلقة حتى يوصل ١٥٠ بار ، وكنت اقدر اوصل السرعة فوق الالف بالراحة لكن خفت على البلف من قوة الطق فكانت هذي أفضل سرعة من ناحية راحة الهمر وضغط المنظم ( اللي رفعته الى ١٥٠ بار )
@@salmanaljuaid6359 ماامداني أجرب تجميعها لكن اتوقع ماراح تختلف عن أي تجميع بسرعة ٩٨٠ سواء كانت ثلاثة وثلاثين او اربعة وثلاثين قرين، الكت هذي تعطي الفولكان قوة لدفع السلق الثقيل ، التجميع يعتمد على تويست سبطانتك ونوعية السلق فما راح يختلف عليك
I purchased this kit and got delivered from SA to EU in no time. Install was easy, did a little mistake and AAO replied instantly for a fix. Everything works as described. Could ‘t recommend more.
Great kit. Seems like you could have made the depinger into a gauge block/port for a pressure gauge. That way we could check the plenum pressure like they do on some of the high end guns. I understand that not everyone wants to drill a hole in their plenum but it at least could be offered as an option.
@African Air Ordnance .. I purchased this kit and installed the black spring with the debounce spring. With the hammer adjustment backed out as far as will fit into the stock the gun is almost impossible to cock. Feels gritty even though I lubed the slip collar well with silicone grease. You have to really yank the cocking lever hard to engage the sear. Also the magazine plates don't fit well. They hold some of the screws at a slight angle so you really have to tighten them down to make the magazines fit the gun again which displaces the o-rings causing them to drag on slugs in two spots. The magazines can no longer be loaded from the top due to the new plate opening being smaller than the original. Now the mags must be loaded from the other side. No problems with any other parts but I have not tried the super heavy spring. V3 .30 cal long, from USA. Please help.
You will need to open the loading slot up on the plate with a Dremel to work for 30 cal also you can slightly open up the screw holes on the mag plates to using a small drill bit when you install the hammer springs you need to remove the plastic guide and install the springs without the plastic guide it Also you only need to put the debounce spring in if you are going to run the Reg over 200 bar please note the springs will be hard to cock at first given that they are more powerful but they will break in
@@AfricanAirOrdnance Removing the debounce spring made it much better. The magazine top plates just have the holes misaligned so drilling them larger still leaves the screw heads at an angle that stops the magazine fitting in the gun. Also the o-rings prevent the magazine indexing. The fix was to open the holes to a little over 3mm and grind the bevel around each hole larger with a 45 degree stone. I designed and 3d printed plastic spacers to replace the top plate o-rings. Available free at thingiverse. Tagged Vulcan 3 and African Air Ordnance. You or anyone else may use them freely. This is not a complaint. I'm happy with the kit and I thank you for your work. AVS 70 grain .30 cal flat base slugs fit my magazines perfectly now.
@@AfricanAirOrdnance I'm happy with the kit so far. You can find my thread titled "Vulcan 3 Power Kit From African Air Ordnance" at airgunnation forum.
These are such dope guns.... EXCEPT they absolutely need an operating pressure gauge (100% critical) and an externally adjustable regulator! Maybe you guys can develop something like that? 😉
A garrafa de fibra de carbono é de 700cc em comparação com 580cc do original a peça instalada no plenário é para reduzir o ruído twang que vem para a arma quando você atira nela como ele cany ser bastante irritante em seu ouvido cada vez que você atirar a arma
what makes the new bottle adapter different than the original? i dont get why u can put a bigger bottle on the new one as apposed to the old one. are the threads different? ill be installing this kit in a few days . i dont know if it makes any sense to even change that part out as i dont plan to get a bigger tank.
You can't remove the threaded end off the original bottle its actually part of the original bottle so if you want to use a aftermarket carbonfibre bottle you need a adapter
@@AfricanAirOrdnance so would the 580 cc bottle from an impact then fit the gun if i change that part out? meaning size of the bottle wouldnt be to big in dia probably close to the same as original?
@@andrefigueroa7315 you can use the same kit for all calibre if you have 25 cal or 30 cal then you only need to open the loading slot on the magazine back plate that comes with the kit. this is easy to do with a Dremel
By keeping pressure on the back of the hammer after the gun is fired on the factory set up after the gun is fired there is a small amount of free space this space let's the the hamer rebound off the back of the valve stem as the poppet closes the small spring eliminate the free travel The hammer bounce is only a issue when you run over 200 bar regulator pressure at low reg pressure its not a issue u do you need to change out the hammer spring you only need to change over if you want to run much higher reg pressure that the factory spring cannot over come to open the valve
Hola buenos dias alguien sabe a cuanto esta regulada esa valvula para lograr esas velocidades de mas de 1000 fps con 40 gr ??? ??? Muchas gracias por responderme
You could do away with the regulator but you would need to make a part that seals of the regulator hole in the airtube or simply adjust the regulator that its open and not regulating the air pressure down
@@AfricanAirOrdnance I do not understand. With my AEA HP I removed the pressure regulator that was inside the tank and I reached 230 jaules without problems. Obviously I have fewer shots but deadly. And compared to the Vulcan 3 it is very small and compact.
@@AfricanAirOrdnance YES also AEA CHALLENGER BULLPUP I'm watching and without regulator. and with the same system. I think that the Vulcan 3 can be improved and reach 200 Jaule easily
@@AfricanAirOrdnance AEA hp 9 mm caliber reaches 274 m/s // 900-905FPS 79gr I can fire 5 good shots. Then the fps drops because it obviously doesn't have the regulator. But as I repeat, it is deadly. The AEA produces large caliber pcp rifles. 30 (7.62mm) 0.35 (9mm) 0.45 (11.45mm) 0.50 (12.7mm)
@African Air Ordnance ok. I did find it. Thanks! Do you have a video for installing these parts for the uragan 2? I've watched your 3 videos on testing and reg adjustment on it. Great helpful information! As with all your videos.
Why because pushing 40 gn Slugs at high verlocity let's see you push 40 gn Slugs at that speed and not get a drop off FYI they don't drop off a cliff it's a gradule slope
@@AfricanAirOrdnance Thank you very much, then it is worth waiting? Please in your opinion which is the best between Vulcan 3 and 2? Shoot only with slugs. Thank you and I'm waiting for the answer.
@@drywallman1986 you need to take the reg out and install in a reg tool, then adjust it where you want it, pretty simple but little more complicated than a gun with a reg gauge
I just got this kit last week from Mr.King , I am astonished on how my Vulcan3 700 transformed, I was able to push NSA 43.5g slugs 6.35 @ 990 fps with almost no effort, the adapter for extra air tank volume 700cc is a must-have mod
The regulator seat metal piece did clearly improve the fps consistancy
Thanks Jeremy, Well done 👍🏻👍🏻👍🏻
Great thank you for your kind support
لاهنت يا حمد كم طلقة تجيك بتنظيم ممتاز تقريبا بعد تركيبك لترقية كيف التجميعات ? افيدني لاهنت
@@salmanaljuaid6359 ولاتهون أخوي سلمان ، ركبت اسطوانة ٧٠٠ ، ورميت اربع محالات (اربعين رصاصة نيلسن ٤٣ قرين) على سرعة ٩٨٠ ونزل الضغط من ثلاثمية بار الى ميتين بار ، يعني بيكفيك الى ستين طلقة حتى يوصل ١٥٠ بار ، وكنت اقدر اوصل السرعة فوق الالف بالراحة لكن خفت على البلف من قوة الطق فكانت هذي أفضل سرعة من ناحية راحة الهمر وضغط المنظم ( اللي رفعته الى ١٥٠ بار )
@@hralhajriify طيب كيف تجميعها ممتاز
@@salmanaljuaid6359 ماامداني أجرب تجميعها لكن اتوقع ماراح تختلف عن أي تجميع بسرعة ٩٨٠ سواء كانت ثلاثة وثلاثين او اربعة وثلاثين قرين، الكت هذي تعطي الفولكان قوة لدفع السلق الثقيل ، التجميع يعتمد على تويست سبطانتك ونوعية السلق فما راح يختلف عليك
I purchased this kit and got delivered from SA to EU in no time. Install was easy, did a little mistake and AAO replied instantly for a fix. Everything works as described. Could ‘t recommend more.
ا
Great kit. Seems like you could have made the depinger into a gauge block/port for a pressure gauge. That way we could check the plenum pressure like they do on some of the high end guns. I understand that not everyone wants to drill a hole in their plenum but it at least could be offered as an option.
Thanks Jeremy for the nice video. What is the amount of pressure on the regulator?
Anytime if I recall it was around 180 Bar
Very nice kit.
Thanks for watching
@African Air Ordnance .. I purchased this kit and installed the black spring with the debounce spring. With the hammer adjustment backed out as far as will fit into the stock the gun is almost impossible to cock. Feels gritty even though I lubed the slip collar well with silicone grease. You have to really yank the cocking lever hard to engage the sear. Also the magazine plates don't fit well. They hold some of the screws at a slight angle so you really have to tighten them down to make the magazines fit the gun again which displaces the o-rings causing them to drag on slugs in two spots. The magazines can no longer be loaded from the top due to the new plate opening being smaller than the original. Now the mags must be loaded from the other side. No problems with any other parts but I have not tried the super heavy spring. V3 .30 cal long, from USA. Please help.
You will need to open the loading slot up on the plate with a Dremel to work for 30 cal also you can slightly open up the screw holes on the mag plates to using a small drill bit when you install the hammer springs you need to remove the plastic guide and install the springs without the plastic guide it Also you only need to put the debounce spring in if you are going to run the Reg over 200 bar please note the springs will be hard to cock at first given that they are more powerful but they will break in
@@AfricanAirOrdnance Will do. Thank you sir.
@@AfricanAirOrdnance Removing the debounce spring made it much better. The magazine top plates just have the holes misaligned so drilling them larger still leaves the screw heads at an angle that stops the magazine fitting in the gun. Also the o-rings prevent the magazine indexing. The fix was to open the holes to a little over 3mm and grind the bevel around each hole larger with a 45 degree stone. I designed and 3d printed plastic spacers to replace the top plate o-rings. Available free at thingiverse. Tagged Vulcan 3 and African Air Ordnance. You or anyone else may use them freely. This is not a complaint. I'm happy with the kit and I thank you for your work. AVS 70 grain .30 cal flat base slugs fit my magazines perfectly now.
@@AfricanAirOrdnance I'm happy with the kit so far. You can find my thread titled "Vulcan 3 Power Kit From African Air Ordnance" at airgunnation forum.
Good evening, I would like to know what is the thickness of the wire of the hammer spring that you put?
What is the thickness about anti-creep?
These are such dope guns.... EXCEPT they absolutely need an operating pressure gauge (100% critical) and an externally adjustable regulator!
Maybe you guys can develop something like that? 😉
Their regulator is one of the best. You can get a reg tester from talon tunes
Amigo quais as medidas da rosca do adaptador de cilindro?
Qual a diferença desse cilindro para o original e essa válvula que foi colocada .qual a função dela?
A garrafa de fibra de carbono é de 700cc em comparação com 580cc do original a peça instalada no plenário é para reduzir o ruído twang que vem para a arma quando você atira nela como ele cany ser bastante irritante em seu ouvido cada vez que você atirar a arma
Olá teria um kit desse para o vulcan 2?
Como faço para adquirir um kit desses?
Very nice
what makes the new bottle adapter different than the original? i dont get why u can put a bigger bottle on the new one as apposed to the old one. are the threads different? ill be installing this kit in a few days . i dont know if it makes any sense to even change that part out as i dont plan to get a bigger tank.
You can't remove the threaded end off the original bottle its actually part of the original bottle so if you want to use a aftermarket carbonfibre bottle you need a adapter
@@AfricanAirOrdnance so would the 580 cc bottle from an impact then fit the gun if i change that part out? meaning size of the bottle wouldnt be to big in dia probably close to the same as original?
@@craftsman2533you would need to remove the fx valve from the bottle then you could use it with the adapter even the 700 cc bottle will work
How May shot's per fill on standard factory settings?
around 6 mags before you fall off reg
How do i purchased you depinger?
Do you have to degas the vulcan 3 if you re only removing barrel to clean?
Thanks
You can email me at africanairordnance@gmail.com
You don't need to degas to remove the barrel
The upgrade kit = is it the same kit across all calibers ? I’m interested in one but when I look it up only one kit is listed. Thanks in advance
@@andrefigueroa7315 you can use the same kit for all calibre if you have 25 cal or 30 cal then you only need to open the loading slot on the magazine back plate that comes with the kit. this is easy to do with a Dremel
@@AfricanAirOrdnance okay thank you ! Yes it would be for .25 caliber .
@@andrefigueroa7315 you can email your order to africanairordnance@gmail.com
@@AfricanAirOrdnance will do thank you for your help
@@AfricanAirOrdnance Does the website still work ? That’s where I seen the kit or would it be faster / easier to just order via email ?
How does that small spring stop hammer bounce?
By keeping pressure on the back of the hammer after the gun is fired on the factory set up after the gun is fired there is a small amount of free space this space let's the the hamer rebound off the back of the valve stem as the poppet closes the small spring eliminate the free travel
The hammer bounce is only a issue when you run over 200 bar regulator pressure at low reg pressure its not a issue u do you need to change out the hammer spring you only need to change over if you want to run much higher reg pressure that the factory spring cannot over come to open the valve
With the bottle upgrade could you then remove the bottle without degassing?
No
what is the anticreep plate actually doing?
It raises the regulator so that the reg orings dosent block the breather hole in the Plenum tube which can cause a sudden loss of power
What's the price of the rifle
I have already written two emails that I would like to buy and whether he would send me to the Czech Republic, without an answer.🙄
You can email me directly at africanairordnace@gmail.com
Is this only usefull for the .22 mag or also for the .25 and .30 magazine?
You can use the plates on bigger calibres but you will need to open the load slot with a dremel
Hola buenos dias alguien sabe a cuanto esta regulada esa valvula para lograr esas velocidades de mas de 1000 fps con 40 gr ??? ??? Muchas gracias por responderme
Good Day el regulador está funcionando a alrededor de 220 bar
@@AfricanAirOrdnance Gracias por responder y cuál es la autonomía con esa regulación?? Muchas gracias por ayudarme
@@CenturyTTR mirando entre media vuelta en el regulador en sentido contrario a las agujas del reloj a 3 cuartos de vuelta en sentido anti horario
@@AfricanAirOrdnance NO me refiero a que cantidad de disparos da en forma pareja con un buen sprint...tu me comprendes ??? Muchas gracias
what happens you delete. the pressure regulator?
You could do away with the regulator but you would need to make a part that seals of the regulator hole in the airtube or simply adjust the regulator that its open and not regulating the air pressure down
@@AfricanAirOrdnance I do not understand. With my AEA HP I removed the pressure regulator that was inside the tank and I reached 230 jaules without problems. Obviously I have fewer shots but deadly. And compared to the Vulcan 3 it is very small and compact.
@@AfricanAirOrdnance YES also AEA CHALLENGER BULLPUP I'm watching and without regulator. and with the same system. I think that the Vulcan 3 can be improved and reach 200 Jaule easily
@@fabiofrtfratantonio8681 AEA what caliber is your AEA the AEA a completely different design so to compare the regulator issue would be silly
@@AfricanAirOrdnance AEA hp 9 mm caliber reaches 274 m/s // 900-905FPS 79gr I can fire 5 good shots. Then the fps drops because it obviously doesn't have the regulator. But as I repeat, it is deadly. The AEA produces large caliber pcp rifles. 30 (7.62mm) 0.35 (9mm) 0.45 (11.45mm) 0.50 (12.7mm)
Love your videos. Very informative. I'm in the state's. How can I get the magazine mod for my uragan 2. Or any upgrades for it? Thank you!
You can order off our website www.africanairordnance.com
@African Air Ordnance ok. I did find it. Thanks! Do you have a video for installing these parts for the uragan 2? I've watched your 3 videos on testing and reg adjustment on it. Great helpful information! As with all your videos.
@@randycombs112 video for the new Uragan 2 upgrade kit will be out on Friday
@@AfricanAirOrdnance that's excellent! Thank you!
How to order one to Egypt
Email me at africanairordnance@gmail.com
I mean to say hello not hell sorry for the typo
how many joules can it dispense?
154 joules in 5 5 cal
Thought it was regulated? Why is your pressure continue to drop?
Why because pushing 40 gn Slugs at high verlocity let's see you push 40 gn Slugs at that speed and not get a drop off FYI they don't drop off a cliff it's a gradule slope
where did u get this larger bottle?
From a local importer but a Google search for 700 cc bottle should help you find one
Hell from Greece may I ask what distance are the targets?
80 meters
Hi sir, this kit work for Uragan 2? Thanks
No but our Uragan Kit will be out end of January 2023
@@AfricanAirOrdnance Thank you very much, then it is worth waiting? Please in your opinion which is the best between Vulcan 3 and 2? Shoot only with slugs.
Thank you and I'm waiting for the answer.
@@Adytzu1979 both are awesome rifles the Vulcan is more powerful and bigger air capacity and a bigger Plenum
@@AfricanAirOrdnance Ok, thank you!
Can I order one I'm in California?
Yes you can also email me directly at africanairordnance@gmail.com we ship to USA with DHL
Why do you only sell to USA? Couldn't you make a way and send it to europe as well?
We ship Worldwide with DHL If you would like to order you are welcome to email me at africanairordnance@gmail.com
@@AfricanAirOrdnance I've already sent an email, I'll be waiting for a response.
@@starlightHT I just sent responded to your email
Hi i want to buy this kit how we can to contact
email me at africanairordnance@gmail.com
Can I order one I'm from Libya
Yes email me at africanairordnance@gmail.com
Awesome, what did you have the reg set at?
There's no Guage you just make small adjustments I believe.
It's not an impact or something lol
@@drywallman1986 you need to take the reg out and install in a reg tool, then adjust it where you want it, pretty simple but little more complicated than a gun with a reg gauge
@@Crazyhorseracing461 I understand how it works bud thank you. I'm about to buy one
Đep thế
What is the TP hole size?
Oval hole that's about 5mm
@@AfricanAirOrdnance is there any isert inside The breach? There is a threaded hole ho Change the TP
@@flightsimulatorx98 there is no insert the barrel is one piece with the transfer port machined into the barrel
So, by simply increasing the spring tension (stronger spring) this will more than double the guns power?
Also need to increase the Regulator pressure.