To everyone whose device still does not work. Turn it off, try turning it upside down for 10 seconds. Clean if a little water leaks somewhere and return it to its normal position. Plug it in and it should work. Before, the device only lit up and sounds were heard. But there was no smoke. When we did this, it worked. To be honest, it's not the same model as in the video, but it's all similar. All the best, greetings.
Wowwww! Tip #1! I even had a suspicion that it needed to be wet and I kept it in the unit with the water just sitting there for 2 days! and it didn’t work! ONLY when I took it out and soaked both ends for a few seconds it worked!! I even tried to return it but they wouldn’t take cus it’s a cheap store! There was a whole adventure with that whereas all that was needed to add to the instructions was to SOAK the tube!! 😵💫😵💫😵💫
The operating instructions in our manual all explain about soaking the cotton filter inside the tube, perhaps the instructions from different manufacturers vary.
Issue 7: I suspect that the very small diaphragm holes of the atomizer head get clogged easily, especially if using ANY kind of fragrance oil, or plain (instead of distilled mineral-free) water. Worst case: the small container of water runs dry and there is just the sticky oil left getting sucked up (recognizable by a colorization of the wick at the top end - havoc is guaranteed. My cheap China humidifier (looking very similar to this one shown here) gave up working after a mere 50hrs or so. I tried all known 'issue' remidies with no success. I even completely disassembled the unit, tried to clean the two 'speaker' diaphragms carefully, used a brandnew cotton wick, all in vain. It is NOT the electronics, it is the ultrasonic head that is the weakest design spot.There is nothing you can do when it starts sputtering or failing completely. All left is to avoid this cheap Chinese crap with a lifetime of a few hours..
@@gladysalfaro3021 Hola, la lámina de aluminio que mencionaste es un disco de atomización con función de vibración de alta frecuencia, no es una simple lámina de metal.
you can check the inner diameter of the tube in your product. Then, refer to the inner diameter to buy a spring that can fit inside. The height of the spring should be around 1cm, in a compressed state is approximately 2-3mm. A simpler solution is to use a spring from a pen as a substitute, and it should work fine in most cases.
It could be due to poor contact in the power supply section, or the touch switch being either insensitive or overly sensitive, resulting in multiple accidental touches that caused it to shut down directly.
A feasible solution is to contact the seller for product replacement or replacement of parts. Since we cannot ascertain the product specifications, we are unable to recommend replacement part options to you.
It works thanks, I never knew that I need to wet the cotton
To everyone whose device still does not work. Turn it off, try turning it upside down for 10 seconds. Clean if a little water leaks somewhere and return it to its normal position. Plug it in and it should work.
Before, the device only lit up and sounds were heard.
But there was no smoke. When we did this, it worked. To be honest, it's not the same model as in the video, but it's all similar.
All the best, greetings.
Useful to know. I will remember to wet the cotton first before using it. Thank you. 😊😊
Wowwww! Tip #1! I even had a suspicion that it needed to be wet and I kept it in the unit with the water just sitting there for 2 days! and it didn’t work! ONLY when I took it out and soaked both ends for a few seconds it worked!! I even tried to return it but they wouldn’t take cus it’s a cheap store! There was a whole adventure with that whereas all that was needed to add to the instructions was to SOAK the tube!! 😵💫😵💫😵💫
The operating instructions in our manual all explain about soaking the cotton filter inside the tube, perhaps the instructions from different manufacturers vary.
@@entulyse yea it was Miniso
Thank you so much for your information
Solved my problem, thanks!
Issue 7: I suspect that the very small diaphragm holes of the atomizer head get clogged easily, especially if using ANY kind of fragrance oil, or plain (instead of distilled mineral-free) water. Worst case: the small container of water runs dry and there is just the sticky oil left getting sucked up (recognizable by a colorization of the wick at the top end - havoc is guaranteed.
My cheap China humidifier (looking very similar to this one shown here) gave up working after a mere 50hrs or so. I tried all known 'issue' remidies with no success. I even completely disassembled the unit, tried to clean the two 'speaker' diaphragms carefully, used a brandnew cotton wick, all in vain. It is NOT the electronics, it is the ultrasonic head that is the weakest design spot.There is nothing you can do when it starts sputtering or failing completely. All left is to avoid this cheap Chinese crap with a lifetime of a few hours..
Thanka for helping ❤
Here 😊😊
This is helpful
Thank u yr u solved my problem
What if I have removed the aluminium steel on the top of the humidifier?😢
broken then.
Se consigue el aluminio de la parte superior del humidificador?
Se puede reemplazar por papel aluminio,?
@@gladysalfaro3021 Hola, la lámina de aluminio que mencionaste es un disco de atomización con función de vibración de alta frecuencia, no es una simple lámina de metal.
My issue is that my diffuser nozzle is break down how can i fix it?
Thanks
My diffuser suddenly stop smokes come out...what to do
Pls can anyone help me where I can get the spring for this particular filter I lost my spring and I have not found it
Very helpful
Mine hasn't got a spring ...?can I buy a replacement?
you can check the inner diameter of the tube in your product. Then, refer to the inner diameter to buy a spring that can fit inside. The height of the spring should be around 1cm, in a compressed state is approximately 2-3mm. A simpler solution is to use a spring from a pen as a substitute, and it should work fine in most cases.
Thanks works ❤❤
I mistakenly created a hole at where the vapor is supposed to come from. Does it mean I can’t use it anymore??
yes
My diffuser is not turing on..
It's just giving me a blink of light for a second and turns off
Please give any solution
It could be due to poor contact in the power supply section, or the touch switch being either insensitive or overly sensitive, resulting in multiple accidental touches that caused it to shut down directly.
@@entulyse Thank you 😍
What kind of cord i have one and was giving to me
Mostly a USB cord without a power adapter.
Mine is not turning on. Its new, i dont know whats the problem😢
If the LED light doesn't turn on the first time you use it, there may be a quality issue with the product. Contact the seller for after-sales support.
thx
how to fix issue 5?
A feasible solution is to contact the seller for product replacement or replacement of parts. Since we cannot ascertain the product specifications, we are unable to recommend replacement part options to you.
the one I have doesn't turn on? What I can do
I'm also facing the Same problem
@@chaitanyakumarmoguluri4556same here
Why is always in charge?
Because no battery inside.
MY CONTAINER MELTED :(