Hey Bars if I could leave one humble opinion about the center bars for Teknos (I’ve used all racing and m2c center bars in my Teknos) is to not over tighten the screw that bolts down into the front top plate. Alot of pressure goes into that part and if it’s overtightened it will eventually break the small piece that holds that bolt. It’s happened to both center braces that I have used. Hope it’s some help awesome video again brotha! 🤙🤙🤙
@@BarstoneRC leaving it loose allows for some very slight flex and it will help from breaking the small piece, although when it breaks it doesn’t really make a difference but I’m sure you’d rather have it in one piece than two 🤣
Nice man make sure you watch your temps with that stock motor it gets hot pretty fast. I put protek fans in the stock fan mount and it seems to help a lot but the stock fans are not that good I melted one stock motor with the max 5 but if you keep a eye on it then it’s not to bad.
That’s what I’m running as well. Stock motor with Max5 and WFO plate with 20/50 gearing. Also got the m2c wide kit and some DuraTrax Lockup. I think it’s a nice setup.
I bought that one but from M2C,I installed yesterday and it just make my MT410 awesome,God bless u my friend 🙏
Thanks for the tekno brace install video ! Just got mine.
No problem 👍
Your welcome brother , I love that brace been running it on my et 48 2.0 since I built it. It’s about time you got it lol
Yeah, I know you told me about it a dozen times I think lol I finally decided to do it. Thank you brother.
Love your shoptime videos. Thanks for posting I always learn something on these
Thanks for stopping by Avery. I appreciate it buddy.
Awesome RC and upgrades
Thanks 👍
Nice little bench video!! Can't wait to see the Teckno out for its next bash!!
Coming soon!
Hey Bars if I could leave one humble opinion about the center bars for Teknos (I’ve used all racing and m2c center bars in my Teknos) is to not over tighten the screw that bolts down into the front top plate. Alot of pressure goes into that part and if it’s overtightened it will eventually break the small piece that holds that bolt. It’s happened to both center braces that I have used. Hope it’s some help awesome video again brotha! 🤙🤙🤙
I appreciate the information buddy I haven’t talked to many people that use these yet, so it’s good to know
@@BarstoneRC leaving it loose allows for some very slight flex and it will help from breaking the small piece, although when it breaks it doesn’t really make a difference but I’m sure you’d rather have it in one piece than two 🤣
It's the only time of the year all my trucks are up and ready to go.Shame the weathers not.✌️
I know everything‘s ready to roll and it’s cold and nasty out
@@BarstoneRC I planned ahead and got myself a V5 kraton ,plus M2C XL kit and various other goodies to put together,keep me sane.✌️
Nice man make sure you watch your temps with that stock motor it gets hot pretty fast. I put protek fans in the stock fan mount and it seems to help a lot but the stock fans are not that good I melted one stock motor with the max 5 but if you keep a eye on it then it’s not to bad.
Yeah, I was beating on it pretty good for about 20 minutes straight the other day and checking it on and off. It was staying pretty decent so far.
That’s what I’m running as well. Stock motor with Max5 and WFO plate with 20/50 gearing. Also got the m2c wide kit and some DuraTrax Lockup. I think it’s a nice setup.
Awesome setup
That brace looks so sweet
Really digging it and it works great
@@BarstoneRC good stuff
What are you running on the servo / servo saver again. All i caught was Hot Racing....? 9:53?
I’m running the whole aluminum, hot, racing, servo saver, set up
Thing is great
On the techno DJ does your battery still fit all right
Yeah, the battery still fit good in there. I run the smaller ones in it the 4000 mA most of the time.
Is that a blx 185 amp esc and a blx motor??
Yes it is.