Hi. Great job. I have just bought the lip spoiler (only). Is it possible to fit it to the standard bumper, or are there other bits I need. I can't tell from your vid, if you're reusing original plastic bits, or if they came with the spoiler ? Basically, is it possible to whip off the old chinless spoiler and fit the new chin spoiler straight on ? Thx.
OK. Parts have arrived. Only bit, I'm unsure of is at about 7m48s you have a little bag and use these at rear of the spoiler ? I don't have these. Can elaborate ? Thanks. Your video has been very helpful.
@@wjones3492 these are the original clips that were included in the kit I got from Suncoast. I could only use those clips in 4 locations. Then, I used the clips I got from Amazon for the rest of the locations because supplied clips would not fit. I think you can reuse these 4 clips as they are the same you will be removing from your current trim. Just be careful removing these clips so that you don’t break them and can reuse them.
did not see another way to contact you so had to use an unrelated video??? I am getting ready to do a coolant change and wondered if you have done a video on this process for the macan??? if so please send the link, if not, well get crackin' so I can watch...... 🤠
Haha… I did a coolant change, but unfortunately it was before I started recording videos…. Maybe this will help: www.macanforum.com/threads/diy-thermostat-replacement-coolant-pump-replacement-macan-s-2015.178740/#post-2631167 In the link above on Macan Forum, I address thermostat change, and I empty and refill coolant. Did my best to document it in writing…. See post # 6 for refilling process.
@@porscheDIY thanks for the info, it is informative but, a lil more involved than a basic coolant change plus different year model parts/places/equipment/etc? If you wanna fly to TX and do mine I will be your cameraman & chef, plus you will get out of that nasty east coast Wx… thanks again 🤠
I have a question sir if i have only this parts (95B807061M1E0) can i use only this parts for mod ? the other parts are necessary or optional ? Actually i dont care perfect fitment on my car. look is more important. Thank you for ur service
I’m not sure if there is a way to make it fit without other parts in the kit. Some parts are there to build the center part of the spoiler and direct air to where it needs to go. Some other parts are there to be able to bolt the spoiler assembly to the bottom of the car. Therefore, I think you will need all the parts. However, maybe you can find a way to attach it without them? Not sure.
Did they not supply the proper parts to complete the installation? Where did you get the white box with all the different black clips? Could you have completed the installation with out it?
Thanks for watching! They provide clips, but they won’t work for some of the spoiler parts. I got an assorted clip box from Amazon (in the video description - included link here as well). I could not have finished installation without those clips. Limited-time deal: GOOACC 415 Pcs Car Retainer Clips & Fastener Remover - 18 Most Popular Sizes Auto Push Pin Rivets Set -Door Trim Panel Clips for GM Ford Toyota Honda Chrysler a.co/d/gyQdWZH
wish i had that much space in my garage..... i have to stop watching your mod videos, i'm spending tooo much $$ on projects :) what is the purpose of those wheel discs/spacers, do you really think/have u noticed a real difference after install that they are doing anything performance wise, or have they turned out to be an optical illusion mod for your high speed trips to the wht mtns?? please send me a link for those jacks
Thanks for watching. The wheel spacers modify the wheel offset, making them more flushed to fender. They have a small effect in handling dynamics, some would say detrimental, others would say it improves handling dynamics, but in my honest opinion, 10 to 12mm change in offset is fine, with no detriment nor significant improvement. It makes the car look more aggressive. To your specific question, I added those more for looks than performance…😉. Here you go: www.quickjack.com I have the 7000TLX, although for the Macan you probably be OK with the 7000TL or even the 5000 series. I have a large SUV I needed to factor into my purchase. They have a purchase guide you can use, and by taking some measurements plus knowing the curb weight of the car, you can make the selection.
Hello, I enjoy your videos. If you have any information please let me know. Can the sports front spoiler be installed with the aero package?
Not that I know of. Thanks for your support.
Thank you for your quick response. Do you think that's possible?
@@rumafarn I don’t think so. This spoiler was specifically designed for the basic bumper. But can’t say for sure.
@@porscheDIY Thank you so much for your valuable opinion.I might try that.
Hi. Great job. I have just bought the lip spoiler (only). Is it possible to fit it to the standard bumper, or are there other bits I need. I can't tell from your vid, if you're reusing original plastic bits, or if they came with the spoiler ? Basically, is it possible to whip off the old chinless spoiler and fit the new chin spoiler straight on ? Thx.
If you look at the description, you will see exact part numbers you need. I’m not reusing parts. All parts are needed.
@@porscheDIY Thx, I'm a bit of a boomer, I'll take another look.
OK. Parts have arrived. Only bit, I'm unsure of is at about 7m48s you have a little bag and use these at rear of the spoiler ? I don't have these. Can elaborate ? Thanks. Your video has been very helpful.
@@wjones3492 these are the original clips that were included in the kit I got from Suncoast. I could only use those clips in 4 locations. Then, I used the clips I got from Amazon for the rest of the locations because supplied clips would not fit. I think you can reuse these 4 clips as they are the same you will be removing from your current trim. Just be careful removing these clips so that you don’t break them and can reuse them.
Perfect, Thanks. Wayne.
did not see another way to contact you so had to use an unrelated video??? I am getting ready to do a coolant change and wondered if you have done a video on this process for the macan??? if so please send the link, if not, well get crackin' so I can watch...... 🤠
Haha… I did a coolant change, but unfortunately it was before I started recording videos…. Maybe this will help: www.macanforum.com/threads/diy-thermostat-replacement-coolant-pump-replacement-macan-s-2015.178740/#post-2631167
In the link above on Macan Forum, I address thermostat change, and I empty and refill coolant. Did my best to document it in writing…. See post # 6 for refilling process.
@@porscheDIY thanks for the info, it is informative but, a lil more involved than a basic coolant change plus different year model parts/places/equipment/etc?
If you wanna fly to TX and do mine I will be your cameraman & chef, plus you will get out of that nasty east coast Wx… thanks again 🤠
@@meseahunt I’ll think about it….😂
I have a question sir
if i have only this parts (95B807061M1E0) can i use only this parts for mod ?
the other parts are necessary or optional ?
Actually i dont care perfect fitment on my car. look is more important.
Thank you for ur service
I’m not sure if there is a way to make it fit without other parts in the kit. Some parts are there to build the center part of the spoiler and direct air to where it needs to go. Some other parts are there to be able to bolt the spoiler assembly to the bottom of the car. Therefore, I think you will need all the parts. However, maybe you can find a way to attach it without them? Not sure.
What is the thickness of your wheel spacers, and do you have it both in the front and rear>?
10mm front and 12mm rear. I got the Flat6 kit.
Did they not supply the proper parts to complete the installation?
Where did you get the white box with all the different black clips?
Could you have completed the installation with out it?
Thanks for watching! They provide clips, but they won’t work for some of the spoiler parts. I got an assorted clip box from Amazon (in the video description - included link here as well). I could not have finished installation without those clips.
Limited-time deal: GOOACC 415 Pcs Car Retainer Clips & Fastener Remover - 18 Most Popular Sizes Auto Push Pin Rivets Set -Door Trim Panel Clips for GM Ford Toyota Honda Chrysler a.co/d/gyQdWZH
Great thanks
Is it possible to identify what clips they are so if I have some one else install it I can supply them
What lowering springs are on your Macan?
I have air suspension and lowered about 30mm using PIWIS.
nice how much spoiler i had 2017 macan s v6
He literally showed the price and where to get it within the first 40 seconds of the video bruh
Yes, please watch the video again, your answer is in fact in first few seconds of the video as stated.
wish i had that much space in my garage..... i have to stop watching your mod videos, i'm spending tooo much $$ on projects :)
what is the purpose of those wheel discs/spacers, do you really think/have u noticed a real difference after install that they are doing anything performance wise, or have they turned out to be an optical illusion mod for your high speed trips to the wht mtns??
please send me a link for those jacks
Thanks for watching. The wheel spacers modify the wheel offset, making them more flushed to fender. They have a small effect in handling dynamics, some would say detrimental, others would say it improves handling dynamics, but in my honest opinion, 10 to 12mm change in offset is fine, with no detriment nor significant improvement. It makes the car look more aggressive. To your specific question, I added those more for looks than performance…😉.
Here you go: www.quickjack.com
I have the 7000TLX, although for the Macan you probably be OK with the 7000TL or even the 5000 series. I have a large SUV I needed to factor into my purchase. They have a purchase guide you can use, and by taking some measurements plus knowing the curb weight of the car, you can make the selection.
@@porscheDIY thanks for the info 🤠
On to the next project 👍🏻
@@porscheDIY im not seeing those same jack stand bridges on their site guess they did away with them??
Does it fit the GTS bumper?
No. The GTS bumper is different and this spoiler won’t fit.
@@porscheDIY thanks for the reply 🙌🏼