Why do fluids in plate heat exchanger typically flow in opposite direction ? This design of heat exchanger is to provide a thermal equilibrium between the 2 fluids( Inlet and outlet). I asked myself that question 2 days ago as well. Excellent video . Thank you .
We use 3 stages plate heat exchanger to preheat the milk/custard/chocolate milk from 4> around 75 degree celcius before pasteurization or sterilization. After the pasteurization it flows back through the heat exchanger to cool it down and heat the cold milk.
Does it matter if you pipe your hot water in from a outdoor wood boiler to the top port flowing down or do you have to pipe hot water in on the bottom port flowing ip
I am a maintenance tech for a major automotive manufacturer. We have 1200 Hydrolic presses that use plate type heat exchangers to cool the hydraulic fluid. Water in one direction and oil in the other. My question is should the water that is leaving the heat exchanger always be on top since heat rises or does that make a difference at all since there is so much volume that flows thru?
The port of water/oil come out or in depends the designer, have to many variables. The transfer of heat will happen because the flow, check pump or sometimes you heat exchangers needs to be cleaned.
also, you promote Defoss, quite a lot. but i dont see any courses with certification option on the website as mentioned in this video couple of times 8:55 am i missing something here?
@@EngineeringMindset oh that's nice. So, that means all course offered have certification? Also, what will the certificate say on it, and what's the validity of it? How to prove it's authencity (other than knowledge, cuz I'm sure I'll be learning it all)
I work for the University of Texas Arlington. Our Thermal Energy Plant started turning steam on yesterday 5-21-2020 and today I'm walking the buildings and some tunnels. My question, what should the guys in the HVAC Department check for on the steam tree, guages, pipes, condensate pumps, etc. in each mechanical room once steam is fully back on? Such as checking gauge PSI before and after. Meaning low/high, before Spence and after Spence PSI. And what to look for on a spence/spirax and pilot valve? What about pop offs? I'm still new to this field and want to learn best and safe practices to shut down and especially start up and after startup. Is there a checklist for the steam tree pipes, valves, and pumps, etc. Thank You, Carl Browning
Before finishing the video I'd say that the reason the flow is flipped every plate is because the heat will be as far as possible from the other heat source so that the water can cool down before it hits the warmer water(in the other plate) coming towards it and thus as you said the colder water will absorb the heat of the warmer plate. Otherwise, the plates will have no thermal difference thus no heat exchange.
I haven’t found any answer regarding irreversibility which is connected to the 2nd law of thermodynamics. Basically, another possible explanation to why is the counter flow more efficient is that it maintains more stable temperature difference during the heat transfer process. For parallel flow, the temperature difference varies a lot during the process. It is a well-known fact that the higher the temperature difference, the higher irreversibility. To prove a better efficiency of the counter flow arrangement, look for the LMTD method and compare both arrangements. You will get a representative value of deltaT higher for the counter flow, hence, considering the same size, the same fluids, heat transfer must be higher for this arrangement.
I will comment and participate. The fluids run counterflow to be more efficient. The fluids running Against the Grain causes hottest fluids to mate with the coldest in order to push the two fluids closer to an equilibrium Or that's my hypothesis.
Can someone help me? I have 2 chillers and a PHX for “free cooling” im always confused on when to run the PHX instead of the chillers. I need a cheat sheet that says medium temp- low humidity= run PHX or high temp high humidity= run chillers I know I have to factor in wet bulb and those things. Thats why it gets confusing for me. That’s why I was hoping someone can help me understand
The answer to your question, I'm using water for the process and steam as the heating medium: The water entering the heat exchanger at the bottom has the largest temperature differential and will extract the most energy out of the outgoing steam condensate. As the water rises through the heat exchanger, the water within the heat exchangers upper region will have the smallest temperature differential, this gives small delta T provides the ability to 'control' the temperature of the outgoing water by modulating the heating medium. If it was reversed, you wouldn't be able to control at all, and you would have all sorts of issues with water hammer etc. in the steam and water side as both condensate and water flashed off and collapses.
Sir I am using glycol water chiller of 5 TR for milk pasteurization and during this process I want to cool my milk to 4 'C but the temperature of milk is not maintaining as I want to maintain. I am using around 300 l of glycol water solution but temperature of milk maintained around 18 'C so what are solutions so that I can maintain 4 'C temperature of milk
I have a big confusion plz solve it .. I see two types of plate heat exchanger , first type have all 4 nozzles is same side or same face , but second type have 2 nozzles on one side and 2 nozzles on opposite side of plate heat exchanger ....what's the cause???
Hello Paul, are you available for paid consulting work? Won't take much of your free time. Just want to pick your brain on a few complex projects and compensate you for your time. Let me know. Thanks!
@@EngineeringMindset hi I am also looking for consulting work on this subject for a commercial building, do u have recommendations who I can be in contact with, many thanks
The fluids flow in opposite directions because it's like a head-on car crash which has a lot more energy than if the cars collided whilst going in the same direction.
⚠️ *Found this video super useful?* Buy Paul a coffee to say thanks: ☕
PayPal: www.paypal.me/TheEngineerinMindset
Why do fluids in plate heat exchanger typically flow in opposite direction ?
This design of heat exchanger is to provide a thermal equilibrium between the 2 fluids( Inlet and outlet).
I asked myself that question 2 days ago as well.
Excellent video .
Thank you .
Best channel on the topic! Well done and very helpful. Would you talk about how to commission an air / water system?
We use 3 stages plate heat exchanger to preheat the milk/custard/chocolate milk from 4> around 75 degree celcius before pasteurization or sterilization. After the pasteurization it flows back through the heat exchanger to cool it down and heat the cold milk.
Where do you work at? Kinda curious to see what companies use these
Excellent video, very educative!! Congrats
Does it matter if you pipe your hot water in from a outdoor wood boiler to the top port flowing down or do you have to pipe hot water in on the bottom port flowing ip
Great videos! Thank you for putting the time into them. Do you have any plans on doing any videos specifically on glycol loops and ice banks?
Learn *HOW HEAT EXCHANGERS WORK* here ➡️ ua-cam.com/video/NCvYPclQNWM/v-deo.html
I am a maintenance tech for a major automotive manufacturer. We have 1200 Hydrolic presses that use plate type heat exchangers to cool the hydraulic fluid. Water in one direction and oil in the other. My question is should the water that is leaving the heat exchanger always be on top since heat rises or does that make a difference at all since there is so much volume that flows thru?
The port of water/oil come out or in depends the designer, have to many variables. The transfer of heat will happen because the flow, check pump or sometimes you heat exchangers needs to be cleaned.
Would like to know what frequency to clean heat exchangers ? How to know when to clean
Fluid flow in the same direction by both fluids will give Thermal Equilibrium
also, you promote Defoss, quite a lot. but i dont see any courses with certification option on the website as mentioned in this video couple of times 8:55
am i missing something here?
There is an exam at the end of each class :)
@@EngineeringMindset oh that's nice. So, that means all course offered have certification?
Also, what will the certificate say on it, and what's the validity of it?
How to prove it's authencity (other than knowledge, cuz I'm sure I'll be learning it all)
very nice explanation....
Can I use a stainless stel brazed heat exchanger for salt water 🤔
Will you make video on Various type of Evaporators?
I work for the University of Texas Arlington. Our Thermal Energy Plant started turning steam on yesterday 5-21-2020 and today I'm walking the buildings and some tunnels.
My question, what should the guys in the HVAC Department check for on the steam tree, guages, pipes, condensate pumps, etc. in each mechanical room once steam is fully back on?
Such as checking gauge PSI before and after. Meaning low/high, before Spence and after Spence PSI.
And what to look for on a spence/spirax and pilot valve?
What about pop offs?
I'm still new to this field and want to learn best and safe practices to shut down and especially start up and after startup.
Is there a checklist for the steam tree pipes, valves, and pumps, etc.
Thank You,
Carl Browning
Thanks for sharing 😀👍
Before finishing the video I'd say that the reason the flow is flipped every plate is because the heat will be as far as possible from the other heat source so that the water can cool down before it hits the warmer water(in the other plate) coming towards it and thus as you said the colder water will absorb the heat of the warmer plate. Otherwise, the plates will have no thermal difference thus no heat exchange.
nice video. One question: which HX type is appropriate for flue gas base water heating ?
Can this heat exchanger be used for domestic hot water in a commercial building ?
Good knowledge thanks,,,
is it possible if i were use just high heat rtv or gasket silicone on my custom heat exhanger?
tq
How to Gas charge in chiller please reply a video..... With Head pressure back pressure and Ampere..... Plzzzzz sir
Why do they flow on opposite directions?
My answer: to maximise cooling or heating of medium and maximise most time and size of the exchanger?
Thank you so much for your nice video.
Tell us regarding design of gasket type plate heat exchanger
I haven’t found any answer regarding irreversibility which is connected to the 2nd law of thermodynamics. Basically, another possible explanation to why is the counter flow more efficient is that it maintains more stable temperature difference during the heat transfer process. For parallel flow, the temperature difference varies a lot during the process. It is a well-known fact that the higher the temperature difference, the higher irreversibility. To prove a better efficiency of the counter flow arrangement, look for the LMTD method and compare both arrangements. You will get a representative value of deltaT higher for the counter flow, hence, considering the same size, the same fluids, heat transfer must be higher for this arrangement.
hi where did u get your engineering knowledge?
I never stop asking questions and reading
@@EngineeringMindset good
I will comment and participate.
The fluids run counterflow to be more efficient.
The fluids running Against the Grain causes hottest fluids to mate with the coldest in order to push the two fluids closer to an equilibrium
Or that's my hypothesis.
Can someone help me? I have 2 chillers and a PHX for “free cooling” im always confused on when to run the PHX instead of the chillers. I need a cheat sheet that says medium temp- low humidity= run PHX or high temp high humidity= run chillers I know I have to factor in wet bulb and those things. Thats why it gets confusing for me. That’s why I was hoping someone can help me understand
The answer to your question, I'm using water for the process and steam as the heating medium: The water entering the heat exchanger at the bottom has the largest temperature differential and will extract the most energy out of the outgoing steam condensate. As the water rises through the heat exchanger, the water within the heat exchangers upper region will have the smallest temperature differential, this gives small delta T provides the ability to 'control' the temperature of the outgoing water by modulating the heating medium. If it was reversed, you wouldn't be able to control at all, and you would have all sorts of issues with water hammer etc. in the steam and water side as both condensate and water flashed off and collapses.
Good job
Very hlpful vdo😊.can u explain abt the spray chamber???
Sir I am using glycol water chiller of 5 TR for milk pasteurization and during this process I want to cool my milk to 4 'C but the temperature of milk is not maintaining as I want to maintain. I am using around 300 l of glycol water solution but temperature of milk maintained around 18 'C so what are solutions so that I can maintain 4 'C temperature of milk
satendra patel kindly check cond and ev valve
I have a big confusion plz solve it ..
I see two types of plate heat exchanger , first type have all 4 nozzles is same side or same face , but second type have 2 nozzles on one side and 2 nozzles on opposite side of plate heat exchanger ....what's the cause???
Hello, please watch this video, we covered this here: ua-cam.com/video/br3gkrXTmdY/v-deo.html
The one with 2 nozzles on either side is probably a two pass plate heat exchanger. Search it!
only if someone uses this simple tech in PC water cooling. hmmm...... i wonder how good that'd be
More surface area for heat transfer
Hello Paul, are you available for paid consulting work? Won't take much of your free time. Just want to pick your brain on a few complex projects and compensate you for your time. Let me know. Thanks!
Hello Jedi, thank you kindly for the offer but unfortunately I'll have to decline.
@@EngineeringMindset hi I am also looking for consulting work on this subject for a commercial building, do u have recommendations who I can be in contact with, many thanks
They follow in opposite directions to increase their relative velocity to each other, thus increasing the heat transfer coefficient.
It is just ti have the highest delta at the Tout
excelente que buena pagina!
The fluids flow in opposite directions because it's like a head-on car crash which has a lot more energy than if the cars collided whilst going in the same direction.
Peltier?
Milk plant project is available
Because heat always travels towards cold? And high pressure ( hot) always flows towards low pressure ( cold)? I dunno
To achieve maximum LMTD
fluid 2 needs time to warm the plate before fluid 1 makes contact with it. Too simplistic ?
Please make video in indonesia langguage.
Achieves highest LMTD
.
3k9ykp
Brother you telling too fastly so reduce your speaking speed & give clear explanation in slow manner to understand for others
Have you tried using the UA-cam controls and simply slowing the video down to maybe 0.75?