Hello ! The curtain of my camera is curled on the sides, pointing inward, but in great shape. Is there a way to flatten it out, with heat maybe ? Thank you
Great video! I just recently bought a Fed 2 that needs some adjustments, specifically the shutter curtains. Do you have a video with a step by step, on how to adjust the shutter curtains properly?
This is the step that nobody shows. It must be a closely guarded secret. At 3.34 we see the drum, where all the magic happens, but then it jumps to showing the pre-cut curtains, then it all affixed to the drum. The drum is the secret. It indexes the first curtain ribbons (connected to the outer parts of the drum) and the second curtain, which is glued to the centre of the drum. The drum has a little notch cut into the top of it, this is second curtain release and the outer has a slot (which the inner notch can be seen through. These have to be in the exact correct aligned position, so first and second curtain are released correctly. The ribbons & curtain have to be glues in exactly the correct position on the drum so they extend the exact correct distance. Too long or two short, then the curtains will not be in the correct open or closed position and if just one is wrong, the curtains will overlap too much, or not enough. The curtains need to overlap when being wound on, else when they travel back over the film gate, light will get through the gap between the two curtains. Yeah, complicated. My solution was to make a jig. Using a curtain set that was original and was still glued onto the drum. The jig holds the two parts of the drum in alignment, using the notch & slot described above. The curtain is then laid out and the length marked on the jig bed. When attaching the new curtain, the edge is clamped at the mark. It can then be glued onto the roller using rubber cement (bike puncture repair glue). Do the same for the ribbons. The two smaller rollers do not require indexing, but must be glued absolutely parallel to the drum. Again a simple jig is used.
Отлично. Я предпочитаю общаться с вами по электронной почте. Я немного говорю по-русски, но не очень хорошо. Мой адрес: a_szuwar@vp.pl Свяжитесь со мной, пожалуйста.
не очень, кадр должен экспонироваться равномерно. Есть конечно допуск когда это будет не заметно, но зачем делать криво, можно сделать ровно и красиво.
Je vois pas l'intérêt de filmer l'avant et l'après la pose des rideaux ? Le seul intérêt c'est de voir la pose des rideaux ! C'est uniquement pour ça que des gens viennent voir des videos comme cela.
Золотые руки!
Здравствуйте, выдержка иногда медлит, как можно смазать?
а как клеить сами шторки
Hello ! The curtain of my camera is curled on the sides, pointing inward, but in great shape. Is there a way to flatten it out, with heat maybe ? Thank you
Great video! I just recently bought a Fed 2 that needs some adjustments, specifically the shutter curtains. Do you have a video with a step by step, on how to adjust the shutter curtains properly?
hey!now I have the same questions too,may I ask about what did you do in the end?cause I haven't find any shutter curtain changing video of Fed2 yet
This is the step that nobody shows. It must be a closely guarded secret. At 3.34 we see the drum, where all the magic happens, but then it jumps to showing the pre-cut curtains, then it all affixed to the drum.
The drum is the secret. It indexes the first curtain ribbons (connected to the outer parts of the drum) and the second curtain, which is glued to the centre of the drum.
The drum has a little notch cut into the top of it, this is second curtain release and the outer has a slot (which the inner notch can be seen through. These have to be in the exact correct aligned position, so first and second curtain are released correctly.
The ribbons & curtain have to be glues in exactly the correct position on the drum so they extend the exact correct distance. Too long or two short, then the curtains will not be in the correct open or closed position and if just one is wrong, the curtains will overlap too much, or not enough. The curtains need to overlap when being wound on, else when they travel back over the film gate, light will get through the gap between the two curtains.
Yeah, complicated. My solution was to make a jig. Using a curtain set that was original and was still glued onto the drum. The jig holds the two parts of the drum in alignment, using the notch & slot described above. The curtain is then laid out and the length marked on the jig bed. When attaching the new curtain, the edge is clamped at the mark. It can then be glued onto the roller using rubber cement (bike puncture repair glue). Do the same for the ribbons.
The two smaller rollers do not require indexing, but must be glued absolutely parallel to the drum. Again a simple jig is used.
@@wibbley1 Здравствуйте, сделайте отдельные видео по этой процедуре
приветствую! шторную ткань где берете?
А сколько стоит ремонт затвора на Киеве-4 ?
Сколько у вас стоит замена шторок на фэд 2?
Buen trabajo
Hello, can I buy the shutter.curtain from you? If yes how much is one set?
hello, write me on e-mail gentle_hand@mail.ru
Гениально!!!
Здравствуйте, а как с вами связаться?
День добрый,а в каком городе ремонтом занимаетесь??
Нижний Новгород
what do you use for shutter curtain material ?
special
@@gentlehand6523 Здравствуйте! С Вами можно как то связатся? Ватсап есть?
У меня фед5с, сколько стоит 💲 замена шторек?
+- цена рабочего на Авито
Привет. У меня вопрос. Вы исправите мою камеру FED 3? Я имею в виду новый снимок. Старик уже истреблен. Спасибо за ответ.
да
Отлично. Я предпочитаю общаться с вами по электронной почте. Я немного говорю по-русски, но не очень хорошо. Мой адрес: a_szuwar@vp.pl Свяжитесь со мной, пожалуйста.
Молодец
Молодец.
Автоспуск не в ту сторону крутится, кожаный чехол будет мешать
Крутится в ту, а вот положение рычага другое. Оно было согласовано с клиентом.
@@gentlehand6523 понял, спасибо. Это я просто по своей судил, не подумал что может быть и по другому:)
Всё хотел узнать, что будет если будет небольшой перекос шторки? Ведь даже с завода выпускали аппараты с перекосом шторки, это считалось нормально.
не очень, кадр должен экспонироваться равномерно. Есть конечно допуск когда это будет не заметно, но зачем делать криво, можно сделать ровно и красиво.
@@gentlehand6523 согласен с вами, если можно красиво, делай красиво)
i have dissassembly my Fed5v, and i am struggling with the reassembly of the curtains! damn this is not in your video :(
Je vois pas l'intérêt de filmer l'avant et l'après la pose des rideaux ? Le seul intérêt c'est de voir la pose des rideaux ! C'est uniquement pour ça que des gens viennent voir des videos comme cela.
Головка кривая с завода, предположение, это так нарезана резьба на самой головке.